ViewSonic Projector PJ359W User Manual

							
PJ359WViewSonic26

IMAGE Menu
IMAGE Menu
ItemDescription
ASPECT
Using the ▲/▼ buttons switches the mode for aspect ratio. For a PC signalNORMAL ó 4:3 ó 16:9 ó 16:10 ó REAL     For an HDMI signalNORMAL ó 4:3 ó 16:9 ó 16:10 ó 14:9 ó REAL     For a Video signal, s-video signal or component video signal4:3 ó 16:9 ó 16:10 ó 14:9 ó REAL     For no signal16:10 (fixed)• This item can be selected only for a proper signal.• The NORMAL mode keeps the original aspect ratio setting.• Performing the automatic adjustment initializes the aspect ratio setting.
OVER SCAN
Using the ▲/▼ buttons adjusts the over-scan ratio.Large (It reduces picture) ó Small (It magnifies picture)• This item can be selected only for a video, s-video and component video signal.• When this adjustment is too large, certain degradation may appear at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the ▲/▼ buttons adjusts the vertical position.Up ó Down• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs please reset the vertical position to the default setting. Pressing the RESET button when the V POSITION is selected will reset the V POSITION to the default setting.• When this function is performed on a video signal, s-video signal, or component video signal, the range of this adjustment depends on the OVER SCAN (above) setting. It is not possible to adjust when the OVER SCAN is set to 10.
H POSITION
Using the ▲/▼ buttons adjusts the horizontal position.Left ó Right• Over-adjusting the horizontal position may cause noise to appear on the screen. If this occurs please reset the horizontal position to the default setting. Pressing the RESET button when the H POSITION is selected will reset the H POSITION to the default setting.• When this function is performed on a video signal, s-video signal, or component video signal, the range of this adjustment depends on the OVER SCAN (above) setting. It is not possible to adjust when the OVER SCAN is set to 10.
From the IMAGE menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the item. 
Then perform it according to the following table.
(continued on next page) 
						

							
ViewSonic27PJ359W

IMAGE Menu
ItemDescription
H PHASE
Using the ▲/▼ buttons adjusts the horizontal phase to eliminate flicker.
Right ó Left
• This item can be selected only for a computer signal or component video signal.
H SIZE
Using the ▲/▼ buttons adjusts the horizontal size.
Large ó Small
• This item can be selected only for a computer signal.• When this adjustment is excessive, the picture may not be displayed correctly.  In such a case, please reset the adjustment by pressing the RESET button during this operation.
AUTO ADJUST EXECUTE
Selecting this item performs the automatic adjustment feature.
For a PC signal The vertical position, the horizontal position, the horizontal phase and the horizontal size (41) will be automatically adjusted. And the aspect ratio will be automatically set to the default. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.
For a video signal, s-video signal or component video signalThe video format best suited for the respective input signal will be selected automatically.This function is available only when the AUTO mode is selected to 
the VIDEO FORMAT item in INPUT menu (29). The vertical position, horizontal position and aspect ratio will be automatically set to the default.
For a component video signal, also the horizontal phase will be automatically set to the default.• The automatic adjustment operation requires about 10 seconds. Also please note that it may not function correctly with some input.
IMAGE Menu (continued) 
						

							
PJ359WViewSonic28

INPUT Menu
INPUT Menu
ItemDescription
PROGRESSIVE
Using the ▲/▼ buttons switches the progress mode.
TV ó FILM ó TURN OFF
• This function is performed only for an interlaced signal of a video, s-video or component video of 525i (480i) or 625i (576i) signal.
• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select TURN OFF, even though the screen image may lose the sharpness.
VIDEO NR
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH ó MID ó LOW
• This function performs only for a video, s-video or component video of 525i(480i) or 625i(576i) signal. 
• When this function is excessive, it may cause a certain degradation of the picture. 
COLOR SPACE
Using the ▲/▼ buttons switches the mode for color space. 
AUTO ó RGB ó SMPTE240 ó REC709 ó REC601      
• This item can be selected only for a computer signal or component video signal.
• The AUTO mode automatically selects the optimum mode. 
• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.
From the INPUT menu, items shown in the table below can 
be performed.
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the item. 
Then perform it according to the following table.
(continued on next page) 
						

							
ViewSonic29PJ359W

ItemDescription
VIDEO FORMAT
Set the video format for the s-video port and video port.(1) Use the ◄/► buttons to select the input port.(2) Using the ▲/▼ buttons switches the mode for video format.
AUTO  ó  NTSC  ó  PAL  ó  SECAM       N-PAL ó M-PAL ó NTSC4.43 
• This item is performed only for a video signal from the VIDEO port or the S-VIDEO port. • The AUTO mode automatically selects the optimum mode.• The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.
HDMI
Using the ▲/▼ cursor buttons changes the HDMI signal mode.
AUTO ó NORMAL ó ENHANCED     
Feature
AUTOSelecting the optimum mode automatically.
NORMALSuitable for DVD signals (16-235)
ENHANCEDSuitable for VGA signals (0-255)
• If the contrast of the screen image is too strong or too weak, try finding a more suitable mode.
FRAME LOCK
Set the frame lock function on/off for each port.(1) Use the ▲/▼ buttons to select one of following ports.
COMPUTER (IN)1 ó COMPUTER (IN)2 ó HDMI                QUIT
(2) Use the ◄/► buttons to turns the frame lock function on/off .
TURN ON ó TURN OFF
• This item can be performed only on a signal  with a vertical frequency of 49 to 51 Hz, 59 to 61 Hz.• When the TURN ON is selected, a moving pictures are displayed more smoothly.• This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF.
COMPUTER IN
Set the computer input signal type for the ports of COMPUTER IN1 and COMPUTER IN2.(1) Use the ◄/► buttons to select a COMPUTER port to be set.
COMPUTER (IN)1 ó COMPUTER (IN)2
(2) Use the ▲/▼ buttons to select the computer input signal type.
AUTO ó SYNC ON G OFF
Sync on Green signal can be supported, if AUTO is selected.• When the AUTO is selected, the picture may be distorted with certain input signals. In such a case, remove the signal connector first and 
select SYNC ON G OFF on the menu, and then reconnect the signal.• Component signal can be supported through COMPUTER IN1 port, if AUTO is selected for the COMPUTER IN1 port.
INPUT Menu
INPUT Menu (continued)
(continued on next page) 
						

							
PJ359WViewSonic30

INPUT Menu
ItemDescription
RESOLUTION
The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button.The RESOLUTION menu will be displayed.
(2)  In the RESOLUTION menu, select the resolution you wish to display using the ▲/▼ buttons. Selecting AUTO will set a resolution appropriate to the input signal.
(3) Pressing the ► or ENTER button when selecting a STANDARD resolution will automatically adjust the horizontal and vertical positions, clock phase and horizontal size and automatically select an aspect ratio. The INFORMATION dialog (42) will be displayed.
(4) To set a custom resolution use the  ▲/▼ buttons to select the CUSTOM and the CUSTOM RESOLUTION box will be displayed. Set the horizontal (HORZ) and vertical (VERT) resolutions using the  ▲/▼/◄/► buttons.Although not all resolutions are guaranteed.
(5) To save the setting place the cursor on the right-most digit and press the ► button.The horizontal and vertical positions, clock phase and horizontal size will be automatically adjusted and an aspect ratio will be automatically selected. After the INFORMATION (42) dialog has displayed for about 10 seconds the screen will return to the RESOLUTION menu displaying the changed resolution.
(6) To revert back to the previous resolution without saving changes place the cursor on the left-most digit and press the ◄ button.The screen will then return to the RESOLUTION menu displaying the previous resolution.
• For some pictures, this function may not work well.
INPUT Menu (continued) 
						

							
ViewSonic31PJ359W

SETUP Menu
SETUP Menu
ItemDescription
AUTO 
KEYSTONE EXECUTE
Selecting this item performs the automatic keystone distortion correction. Projector automatically corrects vertical keystone distortion due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu. When the slant of the projector is changed, execute this function again.
• The adjustable range for correction will vary among inputs. For some input, this function may not work well.• When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, if the projector screen is inclined or angled downward, this function may not work correctly.• When the zoom adjustment is set to the TELE (telephoto focus), this function may be excessive. This function should be used when the zoom adjustment is set to the full WIDE (wide-angle focus) whenever possible.• When the projector is placed on the level (about ±0°), this function may not work.• When the projector is inclined to near ±30 degree or over, this function may not work well.• This function will be unavailable when the Transition Detector is on (47).
KEYSTONE 
Using the ▲/▼ buttons corrects the vertical keystone distortion.
Shrink the top of the image ó Shrink the bottom of the image
• The adjustable range of this function will vary with the type of input signal. For some input, this function may not work well.• This function will be unavailable when the Transition Detector is on (47).
From the SETUP menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button on the ENTER button to execute the 
item. Then perform it according to the following table.
(continued on next page) 
						

							
PJ359WViewSonic32

SETUP Menu
SETUP Menu (continued)
ItemDescription
WHISPER
Using the ▲/▼ buttons turns off/on the whisper mode.
NORMAL ó WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the ▲/▼ buttons switches the mode for mirror status.
NORMAL ó H:INVERT ó V:INVERT ó H&V:INVERT 
If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm (47) will be displayed when projector is restarted after the power switch is turned off.
STANDBY MODE
Using ▲/▼ buttons switches the standby mode setting between NORMAL and SAVING. 
NORMAL ó SAVING
When SAVING is selected, the power consumption in the standby mode is lowered with some functional restriction as below:• When SAVING is selected, any setting of the AUDIO (33) in the standby mode is invalid, and no signal is output in the standby mode. 
						

							
ViewSonic33PJ359W

AUDIO Menu
AUDIO Menu
From the AUDIO menu, items shown in the table below 
can be performed. Select an item using the ▲/▼ cursor 
buttons, and press the ► cursor button or the ENTER 
button to execute the item. Then perform it according to 
the following table.
ItemDescription
VOLUMEUsing the ▲/▼ buttons adjusts the volume.
High ó Low
AUDIO
The combination of a picture and audio input port can be arranged in the menu.The audio coming into the port selected in the (2) is output while an image from the port chosen in the (1) is on screen.(1) Choose a picture input port using ▲/▼ buttons.
• While QUIT is selected, pressing the ◄ button returns to the previous menu.(2) Select one of the audio input ports using ◄/► buttons.
IN (AUDIO IN) ó  ó H (HDMI)
•  disables the audio output.• “H” is abbreviations of HDMI. ”H” can be selected for HDMI port only. When “H” is selected, the audio signal to HDMI port will be output if H is chosen as a display source.• When  is selected to VIDEO, S-VIDEO or COMPONENT port, the C.C. (Closed Caption) is automatically activated, if the C.C. is set to AUTO in the DISPLAY menu of the C.C. menu and the signal from the input port supports the C.C. feature (51). 
HDMI AUDIOThe HDMI AUDIO is set to 1 as default. In case the HDMI audio does not work well, try 2.1 ó 2
QUIT ó COMPUTER 1   ó COMPUTER 2    (COMPUTER IN1) (COMPUTER IN2)AUDIO OUT STANDBY   VIDEO ó S-VIDEO  ó  HDMI 
						

							
PJ359WViewSonic34

SCREEN Menu
SCREEN Menu
ItemDescription
LANGUAGE
Using the ▲/▼ buttons switches the OSD (On Screen Display) language.
SUOMI ó POLSKI ó TÜRKÇE
ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL ó ITALIANO
NORSK ó NEDERLANDS ó PORTUGUÊS ó 日本語
    ó    ó        ó SVENSKA ó
MENU POSITIONUsing the ▲/▼/◄/► buttons adjusts the menu position.To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds.
BLANK
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature  
(19).  It is displayed by pressing the BLANK button.
MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK  
Feature
MyScreenScreen can be registered by the MyScreen item (35).
ORIGINALScreen preset as the standard screen.
BLUE, WHITE, BLACKPlain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes.
From the SCREEN menu, items shown in the table below 
can be performed.
Select an item using the ▲/▼ cursor buttons, and press 
the ► cursor button or ENTER button to execute the item. 
Then perform it according to the following table.
(continued on next page) 
						

							
ViewSonic35PJ359W

SCREEN Menu
ItemDescription
START UP
Using the ▲/▼ buttons switches the mode for the start-up screen.The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.
MyScreen ó ORIGINAL ó TURN OFF    
Feature
MyScreenScreen can be registered by the MyScreen item (35).
ORIGINALScreen preset as the standard screen.
TURN OFFPlain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen (34) after several minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.• When the TURN ON is selected to the MyScreen PASSWORD of SECURITY item in OPTION menu (44), the START UP is fixed to MyScreen.
MyScreen
This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.
1.  Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if you start capturing an image from the current screen.Please wait for the target image to be displayed, and press the ENTER button when the image is displayed. The image will freeze and the frame for capturing will appear. To stop performing, press the RESET or ESC button.
2.   Using the ▲/▼/◄/► buttons adjusts 
the frame position. Please move the frame to the position of the image which you want to use. The frame may not be able to be moved for some input signals. To start registration, press the ENTER 
button. To restore the screen and return to the previous dialog, press the RESET or ESC button. Registration takes several minutes.(continued)
SCREEN Menu (continued)
(continued on next page)