ViewSonic Projector Pj358 User Manual
Have a look at the manual ViewSonic Projector Pj358 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 617 ViewSonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
16ViewSonic PJ358 Adjusting the zoom and focus 1. Use the zoom rng to adjust the screen sze. 2. Use the focus rng to focus the pcture. Operating Focus rngZoom rng Adjusting the projector's elevator When the place to put the projector s slghtly uneven to the left or rght, use the elevator feet to place the projector horzontally. Usng the feet can also tlt the projector n order to project at a sutable angle to the screen, elevatng the front sde of the projector wthn 12 degrees. Ths projector has 2 elevator feet and 2 elevator knobs. An elevator foot s adjustable whle pullng up the elevator knob on the same sde as t. 1. Holdng the projector, pull the elevator knobs up to loose the elevator feet. 2. Poston the front sde of the projector to the desred heght. 3. Release the elevator knobs n order to lock the elevator feet. 4. After makng sure that the elevator feet are locked, put the projector gently. 5. If necessary, the elevator feet can be manually twsted to make more precse adjustments. Hold the projector when twstng the feet. CAUTION ►Do not handle the elevator knobs without holding the projector, snce the projector may drop down. ►Do not tilt the projector other than it elevating its front within 12 degrees using the adjuster feet. A tlt of the projector exceedng the restrcton could cause malfuncton or shortenng the lfetme of consumables, or the projector tself. q To loose an elevator foot, pull up the elevator knob on the same sde as t.To finely adjust, twist the foot.
17ViewSonic PJ358 Adjusting the position 1. Press the POSITION button on the remote control. The “POSITION” ndcaton wll appear on the screen. 2. Use the ▲/▼/◄/► cursor buttons to adjust the picture poston. When you want to reset the operaton, press the RESET button on the remote control durng the operaton. To complete ths operaton, press the POSITION button agan. Even f you do not do anythng, the dalog wll automatcally dsappear after a few seconds. ● The POSITION button does not work for a signal from the USB STORAGE port. ● When this function is performed on a video signal, s-video signal or component vdeo sgnal, some mage such as an extra-lne may appear at outsde of the pcture. ● When this function is performed on a video signal, s-video signal, or component vdeo sgnal, the range of ths adjustment depends on the OVER SCAN n the IMAGE menu settng. It s not possble to adjust when the OVER SCAN s set to 10. Operating Using the automatic adjustment feature 1. Press the AUTO button on the remote control. Pressng ths button performs the followng. For a PC signal The vertcal poston, the horzontal poston, the horzontal phase and the horzontal sze wll be automatcally adjusted. And the aspect rato wll be automatcally set to default. Make sure that the applcaton wndow s set to ts maxmum sze pror to attemptng to use ths feature. A dark pcture may stll be ncorrectly adjusted. Use a brght pcture when adjustng. For a signal from the USB STORAGE The aspect rato wll be automatcally set to the default. For a video signal, s-video signal or component video signal The vdeo format best suted for the respectve nput sgnal wll be selected automatcally. Ths functon s avalable only when the AUTO s selected for the VIDEO FORMAT tem n the INPUT menu. The vert cal pos t on, hor zontal pos t on and aspect rat o w ll be automat cally set to the default. For a component vdeo sgnal, also the horzontal phase wll be automatcally set to the default. ● The automatic adjustment operation requires about 10 seconds. Also please note that t may not functon correctly wth some nput. When ths functon s performed for a vdeo sgnal, a certan extra such as a lne may appear outsde a pcture. HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE AUTO HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE POSITION
18ViewSonic PJ358 Operating Using the magnify feature 1. Press the ON button of MAGNIFY on the remote control. The “MAGNIFY” ndcaton wll appear on the screen (although the ndcaton wll dsappear n several seconds wth no operaton), and the projector wll go nto the MAGNIFY mode. 2. Use the ▲/▼ cursor buttons to adjust the zoom level. To move the zoom area, press the POSITION button n the MAGNIFY mode, then use the ▲/▼/◄/► cursor buttons to move the area. And to finalize the zoom area, press the POSITION button again. To ex t from the MAGNIFY mode and restore the screen to normal, press the OFF button of MAGNIFY on the remote control. ● The projector automatically exits from the MAGNIFY mode when the input sgnal s changed, or when the dsplay condton s changed. ● Although in the MAGNIFY mode, the keystone distortion condition may vary, it wll be restored when the projector exts from the MAGNIFY mode. NOTE • The zoom level can be finely adjusted. Closely watch the screen to find the level you want. Correcting the keystone distortions 1. Press the KEYSTONE button on the remote control. A dalog wll appear on the screen to ad you n correctng the dstorton. 2. Use the ▲/▼ cursor buttons to select the AUTO or MANUAL operation, and press the ► button to perform the following. (1) The AUTO executes automat c vert cal keystone correct on. (2) The MANUAL dsplays a dalog for keystone correcton. Use the ▲/▼ buttons for adjustment. To close the dalog and complete ths operaton, press the KEYSTONE button agan. Even f you do not do anythng, the dalog wll automatcally dsappear after a few seconds. ● The adjustable range of this correction will vary among inputs. For some input, ths functon may not work well. ● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP menu, f the projector screen s nclned or angled downward, ths functon may not work correctly. ● When the zoom adjustment is set to the TELE (telephoto focus), the automatic keystone dstorton correcton may be excessve. Ths functon should be used when the zoom adjustment s set to the full WIDE (wde-angle focus) whenever possble. ● When the projector s placed on the level (about ±0°), the automatc keystone dstorton correcton may not work. ● When the projector s nclned to near ±30 degree or over, ths functon may not work well. ● Ths functon wll be unavalable when Transton Detector s on. HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE KEYSTONE HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE MAGNIFYON/OFF
19ViewSonic PJ358 Operating Temporarily blanking the screen 1. Press the BLANK button on the remote control. The blank screen wll be dsplayed nstead of the screen of nput sgnal. Please refer to the BLANK tem n the SCREEN menu. To ext from the blank screen and return to the nput sgnal screen, press the BLANK button agan. ● The projector automatically returns to the input signal screen when one of the projector’s buttons or the remote control buttons (except ASPECT, POSITION or FREEZE button, also except MY BUTTON1/2 f AUTO KEYSTONE or MyMemory or PICTURE MODE s assgned on these buttons) s pressed. NOTE • The sound s not connected wth the blank screen functon. If necessary, set the volume or mute first. Freezing the screen 1. Press the FREEZE button on the remote control. The “FREEZE” ndcaton wll appear on the screen, and the projector wll go nto the FREEZE mode. To ext the FREEZE mode and restore the screen to normal, press the FREEZE button agan. ● The projector automatically exits from the FREEZE mode when one of the projector’s buttons or remote control buttons of STANDBY/ON, SEARCH, COMPUTER/STORAGE, VIDEO, BLANK, AUTO, VOLUME, MUTE, KEYSTONE, MENU, MAGNIFY and MY BUTTON1/2(except MyMemory or PICTURE MODE s assgned to) s pressed. ● If the projector continues projecting a still image for a long time, the LCD panel mght possbly be burned n. Do not leave the projector n the FREEZE mode for too long. HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE FREEZE HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE BLANK
20ViewSonic PJ358 Operating Using the menu function Ths projector has the followng menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN, OPTION and EASY MENU. EASY MENU conssts of functons often used, and the other menus are classified into each purpose. Each of these menus is operated using the same methods. The basc operatons of these menus are as follows. 1. Press the MENU button on the remote control or the projector. The Advanced MENU, or EASY MENU that has prorty just after powered on, wll appear. Whle the projector s d splay ng any menu, the INPUT/ENTER button on the projector works as the ENTER button and the MENU button on the projector works as the cursor buttons. In the EASY MENU 2. If you want to change t to the Advanced Menu, select the “Go to Advanced Menu...” 3. Use the ▲/▼ cursor buttons to select an tem to operate. 4. Use the ◄/► cursor buttons to operate the tem. In the Advanced MENU 2. Use the ▲/▼ cursor buttons to select a menu. If you want to change t to the EASY MENU, select the EASY MENU. Then press the ► cursor button, or the ENTER button to select an item. The lower layer menu of the selected tem wll appear. 3. Use the ▲/▼ cursor buttons to select an item to operate. Then press the ► cursor button, or the ENTER button to progress. The operaton menu of the selected tem wll appear. 4. Use the ▲/▼ cursor buttons to operate the item. Some functons cannot be performed when a certan nput port s selected, or when a certan nput sgnal s dsplayed. When you want to reset the operaton, press the RESET button on the remote control durng the operaton. Note that some tems (ex. LANGUAGE, H PHASE, VOLUME) cannot be reset. In the Advanced Menu, when you want to return to the previous display, press the ◄ cursor button, or the ESC button on the remote control. 5. Press the MENU button on the remote control agan to close the menu and complete ths operaton. Even f you do not do anythng, the dalog wll automatcally dsappear after about 10 seconds. /07=%1/2764? +/#)5672 2+%674+0276126+105%405*#42055 $4+)*60559×%1064#569× %1.149×6+069×%1.146/2*+)*)#//#&(#7.6 5.%6 #5;/07/;//14;5#8 #5;/07=%1/2764?#52%6 :%76 )QVQ#FXCPEGF/GPW %7561/ 014/#.014/#. J0).+5* #761-;5610-;56102+%674/1&$4+)*6055%1064#56%1.146+065*#420559*+524/+4414456(+.646+/.#0)7#) MENULAMPTEMPPOWER STANDBY/ONINPUT/ENTER INPUT/ENTER button MENU button HOMEPAGE UPPAGE DOWNENDVIDEOSEARCH FREEZEOFFONMAGNIFYASPECT AUTOBLANKMUTEVOLUMEKEYSTONE MY BUTTON POSITION 1 2 ESCENTER MENURESETCOMPUTER/STORAGERESET button ENTER button MENU button Cursor buttons HOMEPAGE UP PAGE DOWNEND VIDEOSEARCH FREEZEOFF ONMAGNIFYASPECTAUTOBLANK MUTE VOLUME KEYSTONEMY BUTTON POSITION 1 2 ESC ENTER MENU RESET COMPUTER/STORAGE ESC button Advanced MENU EASY MENU
21ViewSonic PJ358
EASY MENU
EASY MENU
ItemDescription
ASPECTUsing the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu.
AUTO
KEYSTONE EXECUTE
Using the ► button executes the auto keystone function. See the AUTO KEYSTONE EXECUTE item in SETUP menu.
KEYSTONE Using the ◄/► buttons corrects the vertical keystone distortion.
See
the KEYSTONE item in SETUP menu.
PICTURE MODE
Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to the projected source.
NORMAL ó CINEMA ó DYNAMIC
WHITEBOARD ó DAYLIGHT MODE ó BOARD(BLACK)
COLOR TEMPGAMMA
NORMALMID DEFAULT#1 DEFAULT
CINEMALOW DEFAULT#2 DEFAULT
DYNAMICHIGH DEFAULT#3 DEFAULT
BOARD(BLACK)Hi-BRIGHT-1 DEFAULT#4 DEFAULT
DAYLIGHT MODEHi-BRIGHT-2 DEFAULT#3 DEFAULT
WHITEBOARDMID DEFAULT#5 DEFAULT
• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and COLOR TEMP items in PICTURE menu.• When this function is performed, a certain extra such as a line may appear.
From the EASY MENU, items shown in the table below can
be performed.
Select an item using the ▲/▼ cursor buttons. Then perform
it according to the following table.
#5;/07=%1/2764?#52%6
:%76
)QVQ#FXCPEGF/GPW
%7561/
014/#.014/#.
J0).+5*
#761-;5610-;56102+%674/1&$4+)*6055%1064#56%1.146+065*#420559*+524/+4414456(+.646+/.#0)7#)
(continued on next page)
22ViewSonic PJ358 EASY MENU ItemDescription BRIGHTNESSUsing the ◄/► buttons adjusts the brightness. See the BRIGHTNESS tem n PICTURE menu. CONTRASTUsing the ◄/► buttons adjusts the contrast. See the CONTRAST tem n PICTURE menu. COLORUsing the ◄/► buttons adjusts the strength of whole color. See the COLOR tem n PICTURE menu. TINTUsing the ◄/► buttons adjusts the tint. See the TINT tem n PICTURE menu. SHARPNESSUsing the ◄/► buttons adjusts the sharpness. See the SHARPNESS tem n PICTURE menu. WHISPERUsing the ◄/► buttons turns off/on the whisper mode. See the WHISPER tem n SETUP menu. MIRRORUsing the ◄/► buttons switches the mode for mirror status. See the MIRROR tem n SETUP menu. RESETPerformng ths tem resets all of the EASY MENU tems except the FILTER TIME and LANGUAGE.A dialog is displayed for confirmation. Selecting the RESET using the ▲ button performs resetting. FILTER TIME Performing this item resets the filter time which counts usage time of the air filter.A dialog is displayed for confirmation. Selecting the RESET using the ▲ button performs resetting. See the FILTER TIME tem n OPTION menu. LANGUAGEUsing the ◄/► buttons changes the display language. See the LANGUAGE tem n SCREEN menu. Go toAdvanced Menu... Select “Go to Advanced Menu…” on the menu, and press the ► or ENTER button to use the menu of PICTURE, IMAGE, INPUT, SETUP, SCREEN or OPTION. EASY MENU (continued)
23ViewSonic PJ358 PICTURE Menu PICTURE Menu ItemDescription BRIGHTNESSUsing the ▲/▼ buttons adjusts the brightness.Lght ó Dark CONTRASTUsing the ▲/▼ buttons adjusts the contrast. Strong ó Weak GAMMA Using the ▲/▼ buttons switches the gamma mode. #1 DEFAULT ó #1 CUSTOM ó #2 DEFAULT ó #2 CUSTOM ó #3 DEFAULT #5 CUSTOM ó #5 DEFAULT ó #4 CUSTOM ó #4 DEFAULT ó #3 CUSTOM To adjust CUSTOM Selectng a mode whose name ncludes CUSTOM and then pressing the ► button or the ENTER button d splays a d alog to a d you n adjustng the mode. Ths functon s useful when you want to change the brghtness of partcular tones. Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons. You can dsplay a test pattern for checkng the effect of your adjustment by pressng the ENTER button. Each tme you press the ENTER button, the pattern changes as below. No pattern ð Gray scale of 9 steps Ramp Gray scale of 15 steps The eght equalzng bars correspond to eght tone levels of the test pattern except the darkest n the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalzng adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled wth any of equalzng adjustment bar. • When ths functon s performed, lnes or other dstorton may appear. From the PICTURE menu, tems shown n the table below can be performed. Select an tem usng the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the tem. Then perform t accordng to the followng table. 1 +0 2 +0 3 +0 4 +0 5 +0 6 +0 7 +0 8 +0GAMMA [CUSTOM-1] ENTER, : /07=%1/2764? +/#)5672 2+%674+0276 126+105%40 5*#42055 $4+)*60559×%1064#569× %1.149×6+069× %1.146/2*+)*)#//#&(#7.6 5.%6 #5;/07/;//14;5#8 (contnued on next page)
24ViewSonic PJ358 ItemDescription COLOR TEMP Using the ▲/▼ buttons switches the color temperature mode. To adjust CUSTOM Selectng a mode whose name ncludes CUSTOM and then pressing the ► button or the ENTER button dsplays a dalog to ad you n adjustng the OFFSET and GAIN of the selected mode. OFFSET adjustments change the color ntensty on the whole tones of the test pattern. GAIN adjustments manly affect color ntensty on the brghter tones of the test pattern. Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons. You can dsplay a test pattern for checkng the effect of your adjustment by pressng the ENTER button. Each tme you press the ENTER button, the pattern changes as below. No pattern ð Gray scale of 9 steps Ramp Gray scale of 15 steps • When ths functon s performed, lnes or other dstorton may appear. COLOR Using the ▲/▼ buttons adjusts the strength of whole color. Strong ó Weak • Ths tem can be selected only for a vdeo sgnal, s-vdeo or component vdeo sgnal. TINT Using the ▲/▼ buttons adjusts the tint. Greensh ó Reddsh • Ths tem can be selected only for a vdeo sgnal, s-vdeo or component vdeo sgnal. SHARPNESS Using the ▲/▼ buttons adjusts the sharpness. Strong ó Weak• There may be some noise and/or the screen may flicker for a moment when an adjustment s made. Ths s not a malfuncton. PICTURE Menu PICTURE Menu (continued) +0 +0 RGB +0 COLOR TEMP [CUSTOM-1] OFFSET +0+0 RGB +0 GAINENTER, : HIGH DEFAULT � HIGH CUSTOM � MID DEFAULT � MID CUSTOM LOW DEFAULT � LOW CUSTOM � Hi-BRIGHT-1 DEFAULT � Hi-BRIGHT-1 CUSTOM Hi-BRIGHT-2 DEFAULT � Hi-BRIGHT-2 CUSTOM (contnued on next page)
25ViewSonic PJ358 PICTURE Menu ItemDescription MY MEMORY Ths projector has 4 memores for adjustment data (for all the tems of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each functon.LOAD1 ó LOAD2 ó LOAD3 ó LOAD4 SAVE4 óSAVE3 ó SAVE2 ó SAVE1 LOAD1, LOAD2, LOAD3, LOAD4 Performng a LOAD functon loads the data from the memory lnked n the number ncluded n the functon’s name, and adjusts the pcture automatcally dependng on the data. • The LOAD functons whose lnked memory has no data are skpped. • Remember that the current adjusted condton wll be lost by loadng data. If you want to keep the current adjustment, please save t before performng a LOAD functon. • There may be some noise and the screen may flicker for a moment when loadng data. Ths s not malfuncton. • The LOAD functons can be also performed by the MY MEMORY button whch can be set by the MY BUTTON tem n OPTION menu. SAVE1, SAVE2, SAVE3, SAVE4 Performng a SAVE functon saves the current adjustment data nto the memory lnked n the number ncluded n the functon’s name. • Remember that the current data beng stored of a memory wll be lost by savng a new data nto the memory. PICTURE Menu (continued)