ViewSonic Projector Pj1173 User Manual

PJ1173ViewSonic96

Management with Web browser software
e-SHOT (Still Image Transfer) Display
The projector can display still images that are transferred via the network.
• It is possible to allocate the image file up to 4 in the maximum.
• The image file also can be displayed by using schedule function from the web 
browser. Refer to the item 3.4 Event Scheduling in detail.
NOTE
Transfer image data
Display image data (1 - 4)
e-SHOT transmission requires an exclusive application for your PC. You can...

PJ1173ViewSonic97

e-SHOT (Still Image Transfer) Display (continued)
Configure the following items from a web browser when e-SHOT is used.
Example: If the IP address of the projector is set to 192.168.1.10:
) Enter "http://192.168.1.10/" into the address bar of the web browser.
2)  Enter the Administrator ID and password and 
click [Logon]. 
3) Click [Port Settings] on the main menu.
4)  Click the [Enable] check box to open the Image 
Transfer Port (Port: 9716). Click the [Enable] 
check...

PJ1173ViewSonic98

Management with Web browser software
Command Control via the Network
You can configure and control the projector via the network using RS-232C 
commands.
Communication Port
The following two ports are assigned for the command control.
Command Control Settings
Configure the following items from a web browser when command control is used.
Example: If the IP address of the projector is set to 192.168.1.10:
) Enter “http://192.168.1.10/” into the address bar of the web browser.
2)...

PJ1173ViewSonic99

Management with Web browser software
Command Control via the Network (continued)
When the authentication setting is enabled, the following settings are r\
equired.
7) Click [Security Settings] on the main menu. 
8) Click [Network Control] and enter the desired authentication password.
* See NOTE.
9) Click [Apply] button to save the settings.
• The Authentication Password will be the same for Network Control 
Port1 (Port: 23), Network Control Port2 (Port: 9715), and Image Transfer...

PJ1173ViewSonic00

Management with Web browser software
Command Control via the Network (continued)
Command Format
Command formats differ among the different communication ports.
●  
TCP #23 
You can use the RS-232C commands without any changes. The reply data 
format is the same as the RS-232C commands. However, the following reply 
will be sent back in the event of authentication failure when authentication is 
enabled.
HeaderData lengthRS-232C commandCheck sumConnection ID
0x00x0D3...

PJ1173ViewSonic0

Reply Data format
The connection ID (the data is same as the connection ID data on the sending 
data format) is attached to the RS-232C commands reply data.

ReplyConnection ID
0x06 byte

ReplyConnection ID
0x5 byte

ReplyError codeConnection ID
0xC bytes byte



ReplyDataConnection ID
0xD bytes byte
ReplyStatus codeConnection ID
0xF bytes byte
Management with Web browser software
Command Control via the Network...

PJ1173ViewSonic0

Management with Web browser software
Command Control via the Network (Continued)
Automatic Connection Break
The TCP connection will be automatically disconnected after there is no 
communication for 30 seconds after being established.
The projector does not accept commands without authentication success 
when authentication is enabled. The projector uses a challenge response type 
authentication with an MD5 (Message Digest 5) algorithm.
When the projector is using a LAN, a...

PJ1173ViewSonic03

Maintenance 
Maintenance
A lamp has finite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them\
. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, contact ViewSonic and tell the lamp type number.
Lamp
Type number = RLC-038     (DT0087)
.Turn the projector off, and...

PJ1173ViewSonic04

Maintenance
Lamp warning
Lamp (continued)
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, when 
the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and 
for gas...

PJ1173ViewSonic05

Maintenance
Please check and clean the air filter periodically. If the air filter becomes clogged 
by dust or the like, internal temperatures rise, which could cause a fire, a burn or 
malfunction to the projector. When the indicators or a message prompts you to 
clean the air filter, comply with it as soon as possible. Note that the projector may 
shut down, when the projector heats too much.
Please replace the air filter when it is damaged or too soiled. Preparation of a new...