ViewSonic Projector PJ1165 User Manual

ViewSonic  PJ116530
AUTO Menu (continued)
Item Description
SEARCH Select the TURN ON or the TURN OFF using the S/T buttons.:
    TURN ON 

ViewSonic  PJ116531
SCREEN Menu
With the SCREEN menu, the items shown in the table below can 
be performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
BLANK Select a type of the BLANK screen using the S/T buttons.:
     MyScreen 

ViewSonic  PJ116532
AUTO Menu (continued)
How to register your picture as the MyScreen
  Item Description
MESSAGE Select the TURN ON or the TURN OFF using the S/T buttons.:
    TURN ON 

ViewSonic  PJ116533
OPTION Menu
With the OPTION menu, the items shown in the table below can 
be performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
VOLUME Adjust the volume using the S/T buttons.: 
    High 

ViewSonic  PJ116534
OPTION Menu (continued)
Item Description
SERVICE Pres sing the  X (or the ENTER) button calls the 
SERVICE menu.
SERVICE Menu
Select an item using the  S/T  buttons, and press the 
X  (or the ENTER) button  to perform each function.: 
   FANSPEED  

ViewSonic  PJ116535
NETWORK Menu
This projector provides the NETW ORK function. If you use this 
function, please set up the proj ector according to the Network 
environment in which you use it.
memo When you use a Network suitable  to the DHCP function, the 
following operation is  not required commonly,  because the TURN 
ON is selected to the item  “DHCP” at the shipment time. Please see t he section “Network 
Setting Up”.
Item Description
SETUP Pressing the  X (or the ENTER) button calls 
the IP...

ViewSonic  PJ116536
Network Setting Up
This projector provides the NETWORK function. If you use this function, please consult 
your dealer for information.
To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-1) cable, 
then set up the projector according to the Network environment in which you use it.
When you use a Network unsuitable to the DHCP function
Please set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using the 
NETWORK menu, referring to the section...

ViewSonic  PJ116537
Lamp
 WA R N I N GHIGH 
VOLTAGEHIGH 
TEMPERATUREHIGH 
PRESSURE
The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud 
bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that 
each lamp has a different lifetime, and some may burst or burn out soon after you start 
using them. In addition, when the bulb bursts, it is possible for shards of glass
 to fly into 
the lamp housing, and for gas containing mercury
 to escape...

ViewSonic  PJ116538
Replacing The Lamp
If the indicators or a message prompts you to replace the lamp, replace the lamp as soon 
as possible.
1Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 
45 minutes.
2Contact your dealer to prepare a new lamp. Tell the dealer your lamp type number. If the 
projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to 
replace the lamp.
In the case of replacement by yourself, 
3After making sure that...

ViewSonic  PJ116539
Air Filter
Caring For The Air Filter
The air filter should be cleaned about every 100 hours. If the indicators or a message 
prompts you to clean the air filter, clean the air filter as soon as possible. If the soiling will 
not come off the air filter, or it becomes damaged, then it needs to be replaced. Pleas e 
replace the air filter as soon as possible.
memo When you replace the lamp, please replace also the air filter.
1Turn off the projector, and unplug the power cord. Allow the...