ViewSonic Projector PJ1165 User Manual

							ViewSonic  PJ116530
AUTO Menu (continued)
Item Description
SEARCH Select the TURN ON or the TURN OFF using the S/T buttons.:
    TURN ON 
						

							ViewSonic  PJ116531
SCREEN Menu
With the SCREEN menu, the items shown in the table below can 
be performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
BLANK Select a type of the BLANK screen using the S/T buttons.:
     MyScreen 
						

							ViewSonic  PJ116532
AUTO Menu (continued)
How to register your picture as the MyScreen
  Item Description
MESSAGE Select the TURN ON or the TURN OFF using the S/T buttons.:
    TURN ON 
						

							ViewSonic  PJ116533
OPTION Menu
With the OPTION menu, the items shown in the table below can 
be performed. Perform each operation in accordance with the 
instructions in the table below.
(This table is continued to the following page.) Item Description
VOLUME Adjust the volume using the S/T buttons.: 
    High 
						

							ViewSonic  PJ116534
OPTION Menu (continued)
Item Description
SERVICE Pres sing the  X (or the ENTER) button calls the 
SERVICE menu.
SERVICE Menu
Select an item using the  S/T  buttons, and press the 
X  (or the ENTER) button  to perform each function.: 
   FANSPEED  
						

							ViewSonic  PJ116535
NETWORK Menu
This projector provides the NETW ORK function. If you use this 
function, please set up the proj ector according to the Network 
environment in which you use it.
memo When you use a Network suitable  to the DHCP function, the 
following operation is  not required commonly,  because the TURN 
ON is selected to the item  “DHCP” at the shipment time. Please see t he section “Network 
Setting Up”.
Item Description
SETUP Pressing the  X (or the ENTER) button calls 
the IP ADDRESS menu.
memo This item performs  only when the TURN 
OFF is set to the it em “DHCP” of this 
NETWORK menu.
The IP Address is identificati on number of the projector on the 
Network.
1. Set the IP A ddress using the  S/T  buttons.
memo The same number as t he IP Address of other units cannot be 
used.
Pressing the  X (or the ENTER) button at the 
IP ADDRESS menu ca lls the SUBNET 
MASK menu. The SUBNET MASK is an 
address of the Network.
2. Set the same numbe r as the address of 
the Network to be used.
Pressing the  X (or the ENTER) button at the 
SUBNET MASK menu  calls the DEFAULT 
GATEWAY menu. The DEFAULT GATEWAY 
is the address of  the main device.
3. Set the same numbe r as the address of 
the device as gatewa y to an outer Network.
DHCP Select the TURN ON or  the TURN OFF using the S/T  
buttons. :
    TURN ON  Ù TURN OFF
When you use a Network un suitable to the DHCP 
function, select the TURN OFF.
INFORMATION Pressing the  X (or the ENTER) button 
displays the INFORMATION menu.
The INFORMATION menu shows the 
information about the current Network setting 
as illustrated below.
RESET Select the E XECUTE using the S button to reset the NETWORK 
menu items. :
    EXECUTE  Õ CANCEL
The items of the NETWORK menu ar e collectively returned to the 
initial setting. 
						

							ViewSonic  PJ116536
Network Setting Up
This projector provides the NETWORK function. If you use this function, please consult 
your dealer for information.
To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-1) cable, 
then set up the projector according to the Network environment in which you use it.
When you use a Network unsuitable to the DHCP function
Please set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using the 
NETWORK menu, referring to the section “NETWORK Menu”.
When you use a Network suitable to the DHCP function or has been set up
You can set the IP Address, the Subnet Mask, the Gateway and the DHCP (on/off) using a 
Web Browser of the computer connected to the Network. Although it needs a Web Browser 
of Internet Explorer 4.0 or higher.
Input the same IP address as set to the projector, to the Web Browser of the computer 
connected to LAN.
ex. Case of IP Address = 192.168.1.11
1) Input “http://192.168.1.11”.
2) Click “ENTER”.
3) Input the required data according to the screen.
4) Make sure of the input data, then click Write.
memo These setting will be active after reboot. 
These setting will be stored, and used when 
DHCP is OFF.
5) Click “Return to top page”.
6) Click “REBOOT” to complete this operation. 
						

							ViewSonic  PJ116537
Lamp
 WA R N I N GHIGH 
VOLTAGEHIGH 
TEMPERATUREHIGH 
PRESSURE
The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud 
bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that 
each lamp has a different lifetime, and some may burst or burn out soon after you start 
using them. In addition, when the bulb bursts, it is possible for shards of glass
 to fly into 
the lamp housing, and for gas containing mercury
 to escape from the projector’s vent 
holes
About disposal of a lamp
• This product contains a mercury lamp; do not put in trash. Dispose of in accord with 
environmental laws.
• For lamp recycling, go to www.lamprecycle.org. (in USA)
• For product disposal, contact your local government agency or www.eiae.org (in the 
US) or www.epsc.ca (in Canada).
• For more information, call your dealer.
Disconnect 
the plug from 
the power 
outlet
• If the lamp should break (it will make a loud bang when it does), unplug the 
power cord from the outlet, and make sure to request a replacement lamp 
from your local dealer. Note that shards of glass could damage the 
projector’s internals, or cause injury during handling, so please do not try to 
clean the projector or replace the lamp yourself.
• If the lamp should break (it will make a loud bang when it does), ventilate the 
room well, and make sure not to breathe the gas that comes out of the 
projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, make sure the power switch is off and the power 
cable is not plugged in, then wait at least 45 minutes for the lamp to cool 
sufficiently. Handling the lamp while hot can cause burns, as well as 
damaging the lamp.
• Do not open the lamp cover while the projector is suspended from above. 
This is dangerous, since if the lamp’s bulb has broken, the shards will fall out 
when the cover is opened. In addition, working in high places is dangerous, 
so ask your local dealer to have the lamp replaced even if the bulb is not 
broken.
• Do not use the projector with the lamp cover removed. At the lamp replacing, 
make sure that the screws are screwed in firmly. Loose screws could result 
in damage or injury.
• Use only the lamp of the specified type PRJ-RLC-011.
• If the lamp breaks soon after the first time it is used, it is possible that there 
are electrical problems else where besides the lamp. If this happens, contact 
your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to burst 
during use.
• If the indicators or a message prompts you to replace the lamp (see the 
section “Related Messages” and “Regarding the indicator Lamps”), replace 
the lamp as soon as possible. Using the lamp for long periods of time, or 
past the replacement date, could cause it to burst. Do not use old (used) 
lamps; this is a cause of breakage. 
						

							ViewSonic  PJ116538
Replacing The Lamp
If the indicators or a message prompts you to replace the lamp, replace the lamp as soon 
as possible.
1Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 
45 minutes.
2Contact your dealer to prepare a new lamp. Tell the dealer your lamp type number. If the 
projector is mounted on the ceiling, or if the lamp has broken, also ask the dealer to 
replace the lamp.
In the case of replacement by yourself, 
3After making sure that the projector has 
cooled adequately, slide the knob of a lamp 
cover lock as shown in the Figure.
Then, one side of the lamp cover is raised. 
Pull up the lamp cover and remove it, as 
shown in the Figure.
4Unscrew the 3 screws, and slowly pull out 
the lamp by the handle. Becareful not to 
touch the inside of the lamp case.
5Insert the new lamp, and tighten the 3 
screws firmly to lock it in place.
6Interlocking the 2 tabs of the lamp cover to 
the projector, put the lamp cover on the 
projector.
Then push the point of the lamp cover to fix 
it, as shown in the figure. Make sure that 
the lamp cover doesn’t come up.
7Turn on the projector power, and reset the 
lamp timer.
(1) While the projector running, press the 
MENU button to open the menu.
(2) Choose the “OPTION” on the menu using the S/T button, then press the X button 
or ENTER button.
(3) Choose the “LAMP TIME” using the S/T button, then press and hold the RESET 
button for 3 seconds.
(4) Choose the “RESET” using the S button.
memo Incorrectly resetting of the lamp timer (resetting without replacement, or neglect of 
resetting after replacement) will result in incorrect message functions.
Lamp cover knob Lamp cover
Screws
Ta b s 
						

							ViewSonic  PJ116539
Air Filter
Caring For The Air Filter
The air filter should be cleaned about every 100 hours. If the indicators or a message 
prompts you to clean the air filter, clean the air filter as soon as possible. If the soiling will 
not come off the air filter, or it becomes damaged, then it needs to be replaced. Pleas e 
replace the air filter as soon as possible.
memo When you replace the lamp, please replace also the air filter.
1Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 
45 minutes.
2After making sure that the projector has 
cooled adequately, remove the filter cover 
and the air filter.
3Apply a vacuum cleaner to the filter cover and 
the air filter to clean.
If the soiling will not come off the air filter, or it 
becomes damaged, it needs to be replaced.
If the air filter needs to be replaced, contact 
your dealer to prepare A new air filter. Tell the 
dealer you’re air filter type.
4Insert the cleaned air filter or a new air filter, 
and replace the filter cover.
5Turn on the projector power, and reset the 
filter timer.
(1) While the projector running, press the 
MENU button to open the menu.
(2) Choose the “OPTION” on the menu using 
the S/T button, then press the X button 
or ENTER button.
(3) Choose the “FILTER TIME” using the S/
T button, then press and hold the RESET button for 3 seconds.
(4) Choose the “RESET” using the S button.
memo Incorrectly resetting of the filter timer (resetting without replacement, or neglect of 
resetting after replacement) will result in incorrect message functions.
 WA R N I N G
• Please carefully read the “Quick Start Guide”.
• Before caring the air filter, make sure the power switch is off and the power cable is not 
plugged in, then to replacing wait at least 45 minutes for the lamp to cool sufficiently.
• Use only the air filter of the specified type. Please call ViewSonic Tech Support for P/N.
• Do not use the projector with the air filter and filter cover removed. The use without the 
air filter could result in damage.
 CAUTION
• If the air filter becomes clogged by dust or the like, internal temperature rises and could 
cause malfunction. The power is automatically turned off in order to prevent the 
projector from overheating internally.
Hold the release but-
tons of the filter cover
while pulling down it.
Hold the release button
of the air filter while pull-
ing out it.