ViewSonic Pjd6353s Projector User Manual

							26
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Power On Lock menu after opening the OSD menu system. Select Off by 
pressing /.The message 'INPUT PASSWORD' is displayed. Enter the current 
password.
• If the password is correct, the OSD menu returns to the Security Settings page 
with'Off' shown in the row of Power On Lock. You will not have to enter the 
password next time you turn on the projector.
• If the password is incorrect, the password error message is displayed lasting for 
three seconds, and the message 'INPUT PASSWORD' is displayed for your 
retry. You can press MENU/EXIT on the projector or Exit on the remote 
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should 
you ever need to re-activate the password function by entering the old password. 
						

							27
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only 
display one full screen at a time. 
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the 
projector to automatically search for the signals.
You can also manually select the desired signal by 
pressing one of the source selection keys on the 
remote control, or cycle through the available input 
signals.
1. Press SOURCE on the projector or remote 
control. A source selection bar is displayed. 
2. Press  /  until your desired signal is 
selected and press MODE/ENTER on the 
projector or Enter on the remote control.
Once detected, the selected source information 
will be displayed on the screen for seconds. If 
there are multiple devices connected to the 
projector, repeat steps 1-2 to search for another 
signal.
• The brightness level of the projected image will 
change accordingly when you switch between 
different input signals. Data (graphic) "PC" 
presentations using mostly static images are 
generally brighter than "Video" using mostly 
moving images (movies).
• The input signal type effects the options available 
for the Color Mode. See"Selecting a picture 
mode" on page 32 for details.
• Please see "Projector specifications" on page 64
for the native display resolution of this projector. 
For best display picture results, you should select 
and use an input signal which outputs at this 
resolution. Any other resolutions will be scaled by 
the projector depending upon the 'aspect ratio' 
setting, which may cause some image distortion 
or loss of picture clarity. See "Selecting the aspect 
ratio" on page 30 for details.
Changing Color Space
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6553w/
PJD6383s/PJD6 53w/PJD6653ws/PJD6683w/PJD6683ws series.
In the unlikely event that you connect the projector to a DVD player via the projector’s 
HDMI input and the projected picture displays wrong colors, please change the color space 
to YUV.
To do this:
1. Open the OSD menu and go to the SOURCE menu.
2. Press  to highlight Color Space Conversion and press  /  to select a suitable 
color space.
This function is only available when the HDMI-input port is in use.
D-Sub / Comp. 1 
Video
S-Video D-Sub / Comp. 2 
PJD5126/PJD5226/PJD5226w
PJD6223/PJD6253/PJD6353/
PJD6553w/PJD6653w/PJD6653ws
PJD6683w/PJD6683ws
D-Sub / Comp. 1 
Video
S-Video D-Sub / Comp. 2 
HDMI
PJD6353s/PJD6383/PJD6383s/
6 
						

							28
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These 
adjusters change the image height and projection angle. To adjust the projector:
1. Press the quick-release button and lift the 
front of the projector. Once the image is 
positioned where you want it, release the 
quick-release button to lock the foot in 
position.
2. Screw the rear adjuster feet to fine tune the 
horizontal angle.
To retract the foot, hold up the projector while 
pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster 
feet in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not 
perpendicular to each other, the projected image becomes trapezoidal. To correct this 
situation, see "Correcting keystone" on page 29 for details.
• Do not look into the lens while the lamp is on. The strong light from the lamp may cause 
damage to your eyes.
• Be careful when you press the adjuster button as it is close to the exhaust vent where hot 
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on the 
projector or Auto Sync on the remote control. Within 3 seconds, the built-in Intelligent 
Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the 
best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3 
seconds.
• The screen will be blank while AUTO is functioning.
• This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
1
2
1.Adjust the projected image to the size 
that you need using the zoom ring.2.  If necessary, Sharpen the image by 
rotating the focus ring.
PJD5126/PJD5226/
PJD5226w/PJD6223/
PJD6253/PJD6553w
PJD6353/PJD6353s/
PJD6653w/PJD6653ws/PJD6383/PJD6383s/
PJD66 3w/PJ
D66 3ws/ 8
8 
						

							29
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following one of these steps.
• Using the remote control
Press  /  on the projector or remote control to 
display the Keystone correction page. Press   to 
correct keystoning at the top of the image. Press   
to correct keystoning at the bottom of the image.
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the 
DISPLAY menu is highlighted.
2. Press  to highlight Keystone and press MODE/ENTER on the projector or Enter
on the remote control. The Keystone correction page is displayed.
3. Press   to correct keystoning at the top of the image or press   to correct 
keystoning at the bottom of the image.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys for navigating the picture.
• Using the remote control
1. Press Magnify on the remote control to display the Zoom bar.
2. Press   repeatedly to magnify the picture to a desired size.
3. To navigate the picture, press MODE/ENTER on the projector or Enter on the 
remote control to switch to the paning mode and press the directional arrows 
( , , , ) to navigate the picture.
4. To reduce size of the picture, press MODE/ENTER on the projector or Enter on the 
remote control to switch back to the zoom in/out functionality, and press AUTO/Auto
Sync to restore the picture to its original size. You can also press   repeatedly until 
it is restored to the original size.
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the DISPLAY menu is highlighted.
2. Press
 to highlight Zoom and press MODE/ENTER on the projector or Enter on 
the remote control. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
The picture can only be navigated after the picture is magnified. You can further magnify the 
picture while searching for details.
Press/.Press /. 
						

							30
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and 
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can 
dynamically stretch and scale the image output to a different aspect than that of the image 
input signal. 
To change the projected image ratio (no matter what aspect the source is):
• Using the remote control
1. Press Aspect to show the current setting.
2. Press Aspect repeatedly to select an aspect ratio to suit the!format of the video signal 
and your display requirements.
• Using the OSD menu
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the DISPLAY menu is highlighted.
2. Press
 to highlight Aspect Ratio.
3. Press  /  to select an aspect ratio to suit the format of the video signal and your 
display requirements. 
						

							31
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1.Auto: Scales an image proportionally to fit the 
projector's native resolution in its horizontal 
width. This is suitable for the incoming image 
which is neither in 4:3 nor 16:9 and you want to 
make most use of the screen without altering the 
image's aspect ratio.
2.4:3: Scales an image so that it is displayed in the 
center of the screen with a 4:3 aspect ratio. This 
is most suitable for 4:3 images like computer 
monitors, standard definition TV and 4:3 aspect 
DVD movies, as it displays them without aspect 
alteration.
3.16:9: Scales an image so that it is displayed in 
the center of the screen with a 16:9 aspect ratio. 
This is most suitable for images which are 
already in a 16:9 aspect, like high definition TV, 
as it displays them without aspect alteration.
4.16:10 (PJD5226w/PJD6553w/PJD6653w/
Scales an image so that it is 
  center  of  the  screen  with  a 16:10  
  This  is  most  suitable  for  images  which  
already in a 16:10 aspect, as it displays them 
without aspect alteration
16:10 picture
15:9 picture
4:3 picture
16:9 picture
16:10 picture
PJD6653ws/PJD6683w/PJD6683ws only):
displayed in the
aspect ratio.
are  
						

							32
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to 
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
• Press MODE/ENTER on the projector or Color Mode on the remote control 
repeatedly until your desired mode is selected.
•Go to the PICTURE > Color Mode menu and press  /  to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1.Brightest mode: Maximizes the brightness of the projected image. This mode is 
suitable for environments where extra-high brightness is required, such as using the 
projector in well lit rooms.
2.PC mode: Is designed for presentations under daylight environment to match PC and 
notebook coloring.
3.ViewMatch mode: Switches between high brightness performance and accurate color 
performance.
4.Movie mode:!Is appropriate for playing colorful movies, video clips from digital 
cameras or DVs through the PC input for best viewing in a blackened (little light) 
environment.
5.Dynamic PC mode: Is designed for presentations under daylight environment to 
match PC and notebook coloring. In addition, the projector will optimize the image 
quality using the dynamic PC function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for 
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed 
immediately. 
6.Dynamic Movie mode:!Is appropriate for playing colorful movies, video clips from 
digital cameras or DVs through the PC input for best viewing in a blackened (little 
light) environment. In addition, the projector will optimize the image quality using the 
dynamic Movie function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for 
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed 
immediately. 
7.User 1/User 2 mode: Recalls the settings customized based on the current available 
picture modes. See "Setting the User 1/User 2 mode" on page 33 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr) / HDMI
1.Brightest mode: Optimized for daylight viewing, with living room level ambient 
brightness.
2.Gaming mode: Suitable for all types of entertainment media, including gaming and 
movies. 
						

							33
3.ViewMatch mode: Switches between high brightness performance and accurate color 
performance.
4.Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a 
blackened (little light) home cinema or lounge room environment.
5.Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best 
viewed in a blackened (little light) home cinema or lounge room environment. In 
addition, the projector will optimize the image quality using the dynamic Movie 
function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for 
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed 
immediately.  
6.User 1/User 2 mode: Recalls the settings customized based on the current available 
picture modes. See "Setting the User 1/User 2 mode" on page 33 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable 
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting 
point and customize the settings.
1. Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the PICTURE > Color Mode menu.
3. Press  /  to select User 1 or User 2.
4. Press to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode 
sub-menu item.
5. Press  /  to select a picture mode that is closest to your need.
6. Press  to select a sub-menu item to be changed and adjust the value with  / . 
See Fine-tuning the image quality in user modesbelow for details.
7. When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
8. The confirmation message 'Setting Saved' is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which 
may not be white, the Screen Color feature can help correct the projected picture’s colors to 
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press  /  to select a 
color which is closest to the color of the projection surface. There are several precalibrated 
colors to choose from: Whiteboard,Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available 
whenUser 1 or User 2 mode is selected. You can make adjustments to these functions 
based on your needs. 
						

							34 Adjusting Brightness
Highlight the PICTURE > Brightness menu and press  /.
The higher the value, the brighter the image. And the 
lower the setting, the darker the image. Adjust this 
control so the black areas of the image appear just as 
black and that detail in the dark areas is visible.
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press  / .
The higher the value, the greater the contrast. Use this 
to set the peak white level after you have previously 
adjusted the Brightness setting to suit your selected 
input and viewing environment.
Adjusting Color
Highlight the PICTURE > Color menu and press  / .
Lower setting produces less saturated colors. If the setting is too high, colors on the image 
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press  / .
The higher the value, the more reddish the picture becomes. The lower the value, the more 
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press  / .
The higher the value, the sharper the picture becomes. The lower the value, the softer the 
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press  / .
This feature utilizes a new color-processing algorithm and system level enhancements to 
enable higher brightness while providing truer, more vibrant colors in the projected picture. 
It enables a greater than 50% brightness increase in mid-tone images, which are common in 
video and natural scenes, so the projector reproduces images in realistic and true colors. If 
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press  / .
The options available for color temperature* settings vary according to the signal type 
selected.
1.T1: With the highest color temperature, T1 makes the image appear the most bluish 
white than other settings.
2.T2: Makes images appear bluish white.
3.T3: Maintains normal colorings for white.
4.T4: Makes images appear reddish white.
+50+30+70
0-30+30 
						

							35
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One 
of the common methods of representing white color is known as the “color temperature”. A 
white color with a low color temperature appears to be reddish white. A white color with a 
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture 
theaters, or home theaters, should color management be considered. Color management 
provides fine color control adjustment to allow for more accurate color reproduction, should 
you require it.
If you have purchased a test disc which contains various color test patterns and can be used 
to test the color presentation on monitors, TVs, projectors, etc., you can project any image 
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Go to the DISPLAY menu and highlight Color Management.
2. Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3. Highlight Primary Color and press  /  to select a color from among Red, Yellow, 
Green, Cyan, Blue, or Magenta.
4. Press  to highlight Hue and press  /  to select its range. Increase in the range 
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for 
how the colors relate to each other.
For example, if you select Red and set its 
range at 0, only pure red in the projected 
picture will be selected. Increasing its range 
will include red close to yellow and red close 
to magenta.
5. Press  to highlight Saturation and adjust 
its values to your preference by pressing  /
. Every adjustment made will reflect to the 
image immediately.
For example, if you select Red and set its 
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
6. Press  to highlight Gain and adjust its values to your preference by pressing  /
. The contrast level of the primary color you select will be affected. Every 
adjustment made will reflect to the image immediately. 
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press MENU/EXIT on the projector or Exit on the remote control to exit and save the 
settings.
RED
BLUEGREEN Yellow
Cyan
Magenta