ViewSonic Pjd6353s Projector User Manual

							PJD5126_PJD5226_PJD5226w_
PJD6223_PJD6253_PJD6353_
PJD6353s_PJD6383_PJD6383s_
PJD6553w_PJD6653w_
PJD6653ws_PJD6683w_
PJD6683ws
DLP Projector
User Guide
IMPORTANT:  Please read this User Guide to obtain important information on installing 
and using your product in a safe manner, as well as registering your product for future 
service.  Warranty information contained in this User Guide will describe your limited 
coverage from ViewSonic Corporation, which is also found on our web site at http://www.
YLHZVRQLFFRP LQ (QJOLVK RU LQ VSHFL
						

							i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 
(1) this device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:

						

							ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
 +HHGDOOZDUQLQJV
 )ROORZDOOLQVWUXFWLRQV
 RQRWXVHWKLVXQLWQHDUZDWHU
 &OHDQZLWKDVRIWGU\FORWK
 DFFRUGDQFHZLWKWKH
manufacturer’s instructions.
 DWUHJLVWHUVVWRYHVRURWKHU
GHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
 GLQJW\SHSOXJ$SRODUL]HG
SOXJKDVWZREODGHVZLWKRQHZLGHUWKDQWKHRWKHU$JURXQGLQJW\SHSOXJKDVWZR
blades and a third grounding prong. The wide blade and the third prong are provided 
IRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW
						

							iii
Declaration of RoHS Compliance
LWKLUHFWLYH(&RIWKH
IFHUWDLQKD]DUGRXVVXEVWDQFHVLQ
PHGWRFRPSO\ZLWKWKHPD[LPXP
FRQFHQWUDWLRQYDOXHVLVVXHGE\WKH(XURSHDQ7HFKQLFDO$GDSWDWLRQ&RPPLWWHH7$&DVVKRZQEHORZ
SubstanceProposed Maximum 
ConcentrationActual Concentration
/HDG3E  
0HUFXU\+J  
Cadmium (Cd) 
+H[DYDOHQW&KURPLXP&U
) 
Polybrominated biphenyls (PBB) 
3RO\EURPLQDWHGGLSKHQ\OHWKHUV3%(  
HUWKH$QQH[RIWKH5R+6LUHFWLYHV
as noted below:
([DPSOHVRIH[HPSWHGFRPSRQHQWVDUH
ODPSDQGLQRWKHUODPSVQRW
VSHFL
						

							iv
Copyright Information
Copyright© ViewSonic® Corporation, 2012. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft 
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of 
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are 
trademarks of VESA.
PS/2,  VGA and XGA are registered trademarks of International Business Machines Corporatio\
n.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial erro\
rs or omissions 
contained herein; nor for incidental or consequential damages resulting \
from furnishing this material, or 
the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change 
product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by an\
y means, for any purpose 
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product informat\
ion as it becomes available, 
please register your product on the Internet at: www.viewsonic.com. The ViewSonic ®
 Wizard DVD-
ROM also provides an opportunity for you to print the registration form,\
 which you may mail or fax to 
ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date: PJD5126_PJD5226_PJD5226w_PJD6223_PJD6253_PJD6353_PJD6353s_
PJD6383_PJD6383s_PJD6553w_PJD6653w_PJD6653ws_PJD6683w_PJD6683ws
ViewSonic DLP Projector
VS14295/VS14551/VS14552/VS14191/VS14193/ VS14555/VS14553/VS14195/
VS14554/VS14550
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws_UG_ENG 
Rev. 1C 04-25-12
__________________________________________________________________
__________________________________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you \
and the environment. Please 
use care and dispose of in accordance with local, state or federal laws.\
 
ViewSonic respects the environment and is committed to working and living\
 green. Thank you for being 
part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. 
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/kbase/article.php?id=639
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx  
						

							1
Table of contents
Important safety 
instructions .......................2
Introduction ......................4
Projector features ................................. 4
Shipping contents ................................. 5
Projector exterior view ......................... 6
Controls and functions ......................... 7
Positioning your 
projector..........................12
Choosing a location............................ 12
Projection dimensions ........................ 13
Connection ......................17
Connecting a computer or monitor .... 18
Connecting Video source devices ...... 19
Operation ........................22
Starting up the projector..................... 22
Using the menus................................. 23
Utilizing the password function ......... 24
Switching input signal........................ 27
Adjusting the projected image ........... 28
Magnifying and searching for details. 29
Selecting the aspect ratio ................... 30
Optimizing the image......................... 32
Setting the presentation timer ............ 36
Hiding the image ................................ 37
Locking control keys.......................... 37
Freezing the image ............................. 37
Operating in a high altitude 
environment ....................................... 37
Creating your own startup screen....... 38Controlling the projector through 
a LAN environment ........................... 39
Using the projector in standby mode . 45
Shutting down the projector .............. 45
Menu operation .................................. 46
Maintenance ...................56
Care of the projector .......................... 56
Lamp information .............................. 57
Troubleshooting .............63
Specifications ..................64
Projector specifications...................... 64
Dimensions ........................................ 66
Ceiling mount installation ................. 66
Timing chart ...................................... 67
Copyright information...69
Appendix .........................70
IR control table .................................. 70
RJ45 response table ........................... 72
RS232 command table ....................... 72 
						

							2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information 
technology equipment. However, to ensure safe use of this product, it is important that you 
follow the instructions mentioned in this manual and marked on the product. 
Safety Instructions
1.Please read this manual before you operate your projector. Save it for future 
reference.
2.Do not look straight at the projector lens during operation. The intense light beam 
may damage your eyes.
3.Refer servicing to qualified service personnel.
4.Always open the lens shutter or remove the lens cap when the projector lamp is 
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate 
safely within a mains voltage between 100 to 240 volts AC, but could fail if power 
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate 
or cut out, it is recommended that you connect your projector through a power 
stabilizer, surge protector or uninterruptible power supply (UPS). 
6. Do not block the projection lens with any objects when the projector is under 
operation as this could cause the objects to become heated and deformed or even 
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or 
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for 
approximately 45 minutes prior to removing the lamp assembly for replacement. 
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps 
beyond the rated life could cause them to break on rare occasions. 
9. Never replace the lamp assembly or any electronic components unless the projector is 
unplugged. 
10. Do not place this product on an unstable cart, stand, or table. The product may fall, 
sustaining serious damage. 
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside 
which may cause death if you should come into contact with live parts. The only user 
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer 
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments. 
-  Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls 
and free flow of air around the projector.
-  Locations where temperatures may become excessively high, such as the inside of a 
car with all windows rolled up.
-  Locations where excessive humidity, dust, or cigarette smoke may contaminate optical 
components, shortening the projector's life span and darkening the picture.
-  Locations near fire alarms
-  Locations with an ambient temperature above 40°C / 104°F
-  Locations where the altitudes are higher than 3000 m (10000 feet). 
						

							3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, 
overheating inside the projector may result in a fire.
-  Do not place this projector on a blanket, bedding or any other soft surface. 
-  Do not cover this projector with a cloth or any other item. 
-  Do not place inflammables near the projector.   
14. Always place the projector on a level, horizontal surface during operation.
-  Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of 
more than 15 degrees front to back. Using the projector when it is not fully horizontal 
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall 
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical 
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may 
cause it to fail. If the projector does become wet, disconnect it from the power 
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation. 
Use only qualified ceiling mount kit for mounting the projector and ensure it is 
securely installed. 
19. When the projector is under operation, you may sense some heated air and odor from 
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a 
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the 
projector
We want you to have a pleasant experience using your projector, so we need to bring this 
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a 
proper fitting projector ceiling mount kit and that you ensure it is securely and safely 
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the 
projector may fall from the ceiling due to an improper attachment through the use of the 
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector. 
We recommends that you also purchase a separate Kensington lock compatible security 
cable and attach it securely to both the Kensington lock slot on the projector and the base of 
the ceiling mount bracket. This will perform the secondary role of restraining the projector 
should its attachment to the mounting bracket become loose.  
						

							4
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly 
design to deliver high reliability and ease of use.
The projector offers the following features.
• Dynamic PC and Dynamic Movie function adjusting the power consumption of the 
lamp according to the brightness of the image being projected
• DynamicEco Timer function decreasing the power consumption of the lamp by up to 
70% when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
• Support 3D DLP Link
• Color management allowing color adjustments to your liking
• Less than 1W power consumption when power saving mode is turned on
• Screen Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• Up to 10 sets of picture modes providing multiple choices for different projection 
purposes
• Selectable quick power off function
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction to correct distorted images
• Adjustable color balance control for data/video display
• High brightness projection lamp
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Component HDTV compatibility (YP
bPr)
• The apparent brightness of the projected image will vary depending on the ambient 
lighting conditions, selected input signal contrast/brightness settings, and is directly 
proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers 
specifications. This is normal and expected behavior. 
						

							5
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these 
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those 
illustrated.
Optional accessories
1. Replacement lamp
2. Soft carry case
3. VGA-Component adapterProjector Power Cord VGA Cable
Multi-language user manual DVD Quick Start GuideRemote Control & 
Batteries
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
PJD6553w/PJD6253/
PJD6383/PJD6383s
PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6653w/PJD6653ws/
PJD6683w/PJD6683ws
PJD5126/PJD6223/
PJD5226/PJD5226w
PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6683w/PJD6683ws