ViewSonic Pjd6353s Projector User Manual

							16
PJD6553w
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
There is 3% tolerance among these numbers due to optical component variations. It is 
recommended that if you intend to permanently install the projector, you should physically 
test the projection size and distance using the actual projector in situ before you permanently 
install it, so as to make allowance for this projector's optical characteristics. This will help you 
determine the exact mounting position so that it best suits your installation location.
(a) Screen 
Size
[inch (m)]16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen
(b) Projection distance 
[m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)] (b) Projection distance 
[m (inch)](c) Image 
height
[cm (inch)(d) Vertical 
offset
[cm (inch)]
min. max. min. max.
30(0.8) 0.78 (31) 1.02 (40) 40 (16) 1 (0.4) 0.74 (36) 0.96 (38) 38 (15) 3.8 (1.5)
40(1.0) 1.05 (41) 1.36 (54) 54 (21) 1 (0.5) 0.99 (48) 1.28 (50) 51 (20) 5.1 (2.0)
50(1.3) 1.31 (51) 1.70 (67)  67 (26) 2 (0.7) 1.23 (61) 1.60 (63)  64 (25) 6.4 (2.5)
60(1.5) 1.57 (62) 2.04 (80)  81 (32) 2 (0.8) 1.48 (73) 1.92 (76)  76 (30) 7.6 (3.0)
70(1.8) 1.83 (72) 2.38 (94) 94 (37) 2 (0.9) 1.73 (85) 2.24 (88) 89 (35) 8.9 (3.5)
80(2.0) 2.09 (82) 2.72 (107) 108 (42) 3 (1.1) 1.97 (97) 2.57 (101) 102 (40) 10.2 (4.5)
90(2.3) 2.35 (93) 3.06 (120) 121 (48) 3 (1.2) 2.22 (109) 2.89 (114) 114 (45) 11.4 (4.5)
100(2.5) 2.61 (103) 3.40 (134) 135 (53) 3 (1.3) 2.47 (121) 3.21 (126) 127 (50) 12.7 (5.0)
120(3.0) 3.14 (124) 4.08 (161) 162 (64) 4 (1.6) 2.96 (145) 3.85 (151) 152 (60) 15.2 (6.0)
150(3.8) 3.92 (154) 5.10 (201) 202 (79) 5 (2.0) 3.70 (182) 4.81 (189) 191 (75) 19.1 (7.5)
200(5.1) 5.23 (206) 6.80 (268) 269 (106) 7 (2.6) 4.93 (242) 6.41 (252) 254 (100) 25.4 (10.0)
250(6.4) 6.54 (257) 8.50 (335) 337 (132) 8 (3.3) 6.17 (303) 8.02 (316) 318 (125) 31.8 (12.5)
300(7.6) 7.84 (309) 10.20 (401) 404 (159) 10 (4.0) 7.40 (363) 9.62 (379) 381 (150) 38.1 (15.0)
(a) Screen 
Size
[inch (m)]16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen
(b) Projection 
distance [m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)] (b) Projection 
distance [m (inch)](c) Image 
height
[cm (inch)(d) Vertical 
offset
[cm (inch)]
30(0.8) 0.32 (12) 40 (16) 2 (0.8) 0.30 (12) 38 (15) 3.8 (1.5)
40(1.0) 0.42 (17) 54 (21) 3 (1.1) 0.40 (16) 51 (20) 5.1 (2.0)
50(1.3) 0.53 (21) 67 (26) 3 (1.3) 0.50 (20) 64 (25) 6.4 (2.5)
60(1.5) 0.63 (25) 81 (32) 4 (1.6) 0.60 (23) 76 (30) 7.6 (3.0)
70(1.8) 0.74 (29) 94 (37) 5 (1.9) 0.70 (27) 89 (35) 8.9 (3.5)
80(2.0) 0.84 (33) 108 (42) 5 (2.1) 0.79 (31) 102 (40) 10.2 (4.0)
90(2.3) 0.95 (37) 121 (48) 6 (2.4) 0.89 (35) 114 (45) 11.4 (4.5)
100(2.5) 1.05 (41) 135 (53) 7 (2.6) 0.99 (39) 127 (50) 12.7 (5.0)
120(3.0) 1.26 (50) 162 (64) 8 (3.2) 1.19 (47) 152 (60) 15.2 (6.0)
150(3.8) 1.58 (62) 202 (79) 10 (4.0) 1.49 (59) 191 (75) 19.1 (7.5)
200(5.1) 2.11 (83) 269 (106) 13 (5.3) 1.99 (78) 254 (100) 25.4 (10.0)
250(6.4) 2.63 (104) 337 (132) 17 (6.6) 2.48 (98) 318 (125) 31.8 (12.5)
300(7.6) 3.16 (124) 404 (159) 20 (7.9) 2.98 (117) 381 (150) 38.1 (15.0) 
						

							17
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted. 
• In the connections shown below, some cables may not be included with the projector (see 
"Shipping contents" on page 5). They are commercially available from electronics stores.
• The connection illustrations below are for reference only. The rear connecting jacks 
available on the projector vary with each projector model.
• For detailed connection methods, see pages 18-21.
1. VGA cable
2. VGA to DVI-A cable
3. USB cable
4. Component Video to VGA (D-Sub) 
adapter cable5. S-Video cable
6. Video cable
7. Audio cable
8. HDMI cable
TYPE B
USBLAN
COMPUTER IN 2
RS-232HDMIMONITOR OUTCOMPUTER IN 1
2 S-ViseoVideo
Audio in
1
Audio 
out
TYPE B
USB
COMPUTER IN 2RS-232MONITOR OUT
COMPUTER IN 1
S-ViseoVideoAudio in
Audio 
out
5
7
7748
1
6312
Notebook or 
desktop computer
Speakers orA/V device
Monitor
(DVI) (VGA)
PJD6223/PJD6253/
PJD6353/PJD6353s/
PJD6553w/PJD6653w/
PJD6683ws
PJD5126/PJD5226/
PJD5226w PJD6383/PJD6383s/
PJD6653ws/PJD6683w/ 
						

							18
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both 
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are 
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the 
computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER 
IN 2 signal input socket on the projector.
3. If you wish to use the remote paging function, take a USB cable and connect the 
larger end to the USB port of the computer, and smaller end to the Type B USB socket 
on the projector. See "Using the remote mouse control" on page 10 for details.
Many notebooks do not turn on their external video ports when connected to a projector. 
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a 
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press 
FN and the labeled function key simultaneously. Refer to your notebook's documentation to 
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you 
can connect the MONITOR OUT signal output socket on the projector to an external 
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on page 
18.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the 
D-Sub input socket of the video monitor. 
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable 
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
• For the PJD5126/PJD5226/PJD5226w, the MONITOR OUT output only works when 
COMPUTER IN 1 is made to the projector.
• For the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383sPJD6553w/PJD6653w/
 COMPUTER IN 1 or COMPUTER IN 2 is made to the projector.
• To use this connection method when the projector is in standby mode, turn on the Active 
VGA Out function under the SYSTEM SETUP: Advanced > Standby Settings menu.
PJD6653ws/PJD6683w/PJD6683ws,
MONITOR OUT output only works when 
						

							19
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the 
following output sockets:
• HDMI
• Component Video
•S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above 
connecting methods, however each provides a different level of video quality. The method 
you choose will most likely depend upon the availability of matching terminals on both the 
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped 
with a HDMI socket, you can enjoy uncompressed digital video quality.
See"Connecting an HDMI device" on page 20for how to connect the projector to a HDMI 
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be 
confused with composite video). Digital TV tuner and DVD players output Component 
video natively, so if available on your devices, this should be your connection method of 
choice in preference to (composite) video.
See"Connecting a Component Video source device" on page 20 for how to connect the 
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video. 
If you have both composite Video and S-Video output terminals on your Video source 
device, you should elect to use the S-Video option.
See"Connecting an S-Video source device" on page 21 for how to connect the projector to 
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than 
optimal result from your projector, being the least video quality of the available methods 
described here.
See"Connecting a composite Video source device" on page 21for how to connect the 
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio 
functionality accompanying data presentations for business purposes only. They are not 
designed for, nor intended for stereo audio reproduction use as might be expected in home 
theater or home cinema applications. Any stereo audio input (if provided), is mixed into a 
common mono audio output through the projector speaker.
The table below describes where the sound is from when different source is connected.
Input source COMPUTER IN 1 COMPUTER IN 2,VIDEO,S-VIDEO
The projector can play 
the sound from...AUDIO IN 1 AUDIO IN 2 
						

							20
If you wish, you can make use of the projector (mixed mono) speaker in your presentations, 
and also connect separate amplified speakers to the Audio Out socket of the projector. The 
audio output is a mixed mono signal and controlled by the projector Volume and Mute 
settings.
If you have a separate sound system, you will most likely want to connect the audio output 
of your Video source device to that sound system, instead of to the mono audio projector.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI 
devices.
To connect the projector to an HDMI device:
1. Take an HDMI cable and connect one end to the HDMI-output port of the video 
device.
2. Connect the other end of the cable to the HDMI-input port on the projector. 
• In the unlikely event that you connect the projector to a DVD player via the projector’s 
HDMI input and the projected picture displays wrong colors, please change the color 
space to YUV. See "Changing Color Space" on page 27 for details.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See"Connecting audio" on page 19 for details.
• The HDMI input port is only available on the PJD6223/PJD6253/PJD6553w series.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video 
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 
RCA type connectors to the Component Video output sockets of the Video source 
device. Match the color of the plugs to the color of the sockets; green to green, blue to 
blue, and red to red.
2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a 
D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the 
projector.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See"Connecting audio" on page 19 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
•
VGA-Component adapter
(ViewSonic P/N: CB-00008906) 
						

							21
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket 
available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video 
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See"Connecting audio" on page 19 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• If you have already made a Component Video connection between the projector and this 
S-Video source device using Component Video connections, you need not connect to this 
device using an S-Video connection as this makes an unnecessary second connection of 
poorer picture quality. See"Connecting Video source devices" on page 19 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video 
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of the 
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
connected. See"Connecting audio" on page 19 for details.
• If the selected video image is not displayed after the projector is turned on and the correct 
video source has been selected, check that the Video source device is turned on and 
operating correctly. Also check that the signal cables have been connected correctly.
• You need only connect to this device using a composite Video connection if Component 
Video and S-Video inputs are unavailable for use. See"Connecting Video source devices" 
on page 19for details. 
						

							22
Operation
Starting up the projector
1. Plug the power cord into the projector and into a 
wall socket. Turn on the wall socket switch 
(where fitted). Check that the POWER 
indicator light on the projector flashes blue 
after power has been applied.
2. Press POWER on the projector or remote 
control to start the projector. The POWER 
indicator light stays blue when the projector is 
on.
(If necessary) Rotate the focus ring to adjust the image clearness.
• If the projector is still hot from previous activity, it will run the cooling fan for 
approximately 90 seconds before energizing the lamp. 
• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before 
turning it off.
3. If the projector is activated for the first time, select your OSD language following the 
on-screen instructions.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being 
scanned appears in the upper left corner of the screen. If the projector doesn't detect a 
valid signal, the message 'No Signal' will continue to be displayed until an input 
signal is found.
You can also press SOURCE on the projector or remote control to select your desired 
input signal. See "Switching input signal" on page 27 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will 
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal 
which is compatible with the projector's resolution or set the input signal to a lower setting. 
See "Timing chart" on page 67 for details.
II 
						

							23
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various 
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please set them to your familiar language first.
1. Press MENU/EXIT on the projector or 
Menu on the remote control to turn the 
OSD menu on.3. Press  to highlight 
Language and press  /  to 
select a preferred language.
2. Use  /  to highlight the SYSTEM
SETUP: Basic menu.4. Press MENU/EXIT twice* on 
the projector or Exit on the 
remote control to leave and 
save the settings.
*The first press leads you back 
to the main menu and the 
second press closes the OSD 
menu.
:DISPLAY
:PICTURE
:SOURCE:SYSTEM SETUP: Basic
:SYSTEM SETUP: Advanced
:INFORMATION
Current input 
signal
Main menu icon
Sub-menu
Highlight
Go to the 
previous page 
or to exit.Sta t us
Screen Color
Aspect Ratio
Phase
H. Size
ZoomOff
Auto
16
0
MENU ExitAnalog RGB
ENTERKeystonePosition
3D Sync On
Disable 3D Sync Invert
Color Management
Screen Color
Aspect Ratio
Position
Phase
H. Size
ZoomOff
Auto
MENUExit
Keystone
16
0
Analog RGB3D Sync On
3D Sync Invert
Color ManagementDisableProjector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table
Disable
Disable
Off
Disable
ViewSonicEnglishLanguage
Screen Capture
Message On
LAN Control Settings
Projector Position
Auto Power Off
Blank Timer
Timer Controller Panel Key Lock
Splash Screen
Analog RGB
MENU Exit
Front Table
Disable
Disable
Off
Disable
ViewSonicEnglish Language
Screen Capture
Message On
LAN Control Settings 
						

							24
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option 
for setting up password security. The password can be set through the On-Screen Display 
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on 
page 23.
You will be inconvenienced if you activate the password functionality and subsequently forget 
the password. Print this user manual (if necessary) and write the password you used in this 
manual, and keep it in a safe place for later use.
Setting a password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security 
Settings menu. Press MODE/ENTER on the projector or Enter on the remote 
control. The Security Settings page is displayed.
2. Highlight Power On Lock and select On by pressing  / .
3. As pictured to the right, the four arrow keys 
( , , , ) respectively represent 4 digits 
(1, 2, 3, 4). According to the password you desire 
to set, press the arrow keys to enter six digits for 
the password.
4. Confirm the new password by re-entering the 
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
5. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote 
control.
• Once a password has been set, the projector cannot be used unless the correct password 
is entered every time the projector is started.
• The digits being input will be displayed as asterisks on-screen. Write your selected 
password down here in this user manual in advance or right after the password is entered 
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password
If the password function is activated, you will be asked 
to enter the six-digit password every time you turn on 
the projector. If you enter the wrong password, the 
password error message as pictured to the right is 
displayed lasting for three seconds, and the message 
'INPUT PASSWORD' follows. You can retry by 
entering another six-digit password, or if you did not 
record the password in this user manual, and you absolutely do not remember it, you can use 
the password recall procedure. See "Entering the password recall procedure" on page 25 for 
details.
If you enter an incorrect password 5 times in succession, the projector will automatically 
shut down in a short time.
INPUT NEW PASSWORD
Back MENU
Password Error
Please try again. 
						

							25
Entering the password recall procedure
1. Press and hold AUTO on the projector or Auto
Sync on the remote control for 3 seconds. The 
projector will display a coded number on the 
screen.
2. Write down the number and turn off your 
projector.
3. Seek help from the local service center to decode 
the number. You may be required to provide 
proof of purchase documentation to verify that you are an authorized user of the 
projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security 
Settings > Change Password menu.
2. Press MODE/ENTER on the projector or Enter on the remote control. The message 
'INPUT CURRENT PASSWORD' is displayed.
3. Enter the old password.
• If the password is correct, another message 'INPUT NEW PASSWORD' is 
displayed.
• If the password is incorrect, the password error message is displayed lasting for 
three seconds, and the message 'INPUT CURRENT PASSWORD' is 
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter 
the new password next time the projector is started.
7. To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote 
control.
The digits being input will be displayed as asterisks on-screen. Write your selected password 
down here in this user manual in advance or right after the password is entered so that it is 
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
Please write down the recall code, 
and contact ViewSonic 
Customer Center.
Recall code:
0 2 1 2
RECALL PASSWORD
Exit
MENU