ViewSonic Pjd6235 Projector User Manual

36
Hiding the image
In order to draw the audience's full attention to the presenter, you can use   on the 
projector or Blank on the remote control to hide the screen image. Press any key on the 
projector or remote control to restore the image. The word 'BLANK' appears at the lower 
right corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETTING: BASIC > Blank Timermenu to
let the projector return the image automatically after a period of time when...

37
To activate the High Altitude Mode:
1. Press MENU/EXIT on the projector or Menu on 
the remote control and then press  /  until the 
SYSTEM SETTING: ADVANCED menu is 
highlighted.
2. Press  to highlight High Altitude Mode and 
press /  to select On. A confirmation 
message is displayed.
3. Highlight Yes and press MODE/ENTER on the projector or Enter on the remote 
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level 
because of increased fan speed...

38
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the DISPLAY menu is highlighted.
2. Press  to highlight 3D Settings and press MODE/ENTER on the projector or 
Enter on the remote control.
3. Press  to highlight 3D Sync and press MODE/ENTER on the projector or Enter
on the remote control.
4. Press  to select a 3D Sync setting according to the table below and then press 
MODE/ENTER on the projector or Enter on the remote control to confirm.
When the 3D Sync...

39
Controlling the projector through a LAN 
environment
The projector supports Crestron® software. With correct settings for the LAN Control 
Settings menu, you can manage the projector from a computer using a web browser when 
the computer and the projector are properly connected to the same local area network. 
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port....

40
4. Press   to select the item you want to modify and press MODE/ENTER on the 
projector or Enter on the remote control.
5. Press  /  to move the cursor and the press / to enter the value.
6. To save the settings, press MODE/ENTER on the projector or Enter on the remote 
control. If you do not want to save the settings, press MENU/EXIT on the projector 
orMenu on the remote control.
7. Press  to highlight Apply and press MODE/ENTER on the projector or Enter on 
the remote control.
• If the RJ45 cables...

41
controllers of AMX connected to the same network. For the Details of AMX Device 
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a network which supports Simple Mail Transfer 
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See 
"About Crestron e-Control®" on page 42 for details. 
Please pay attention to the limitation of input...

42
 / > < $ % +   '  " are prohibited.
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control. 
See"2. PICTURE menu" on page 52 and "Projector" on page 7 for details.
ii. To switch between input signals, click on your desired signal.
• The Menu button can also be used to go back to previous OSD menus,...

43
2. The tools page allows you to manage the projector, configure the LAN control 
settings and secure access of remote network operation on this projector.
i. This section is only used with the Crestron Control System. Please contact 
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of 
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has...

44
3. The info page displays the information and status of this projector.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in 
the upper right corner of the screen. You will be able to deliver messages to 
RoomView™ software administrators/users who connect to the same local area 
network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the...

45
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, 
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned 
on). To use these functions, be sure you have turned on the corresponding menus under 
SYSTEM SETTING: BASIC > Standby Settings, and the cable connections are...