ViewSonic Pjd6235 Projector User Manual

46
Shutting down the projector
1. Press POWER and a confirmation message 
is displayed prompting you. 
If you don't respond in a few seconds, the 
message will disappear.
2. Press POWER a second time.
3. Disconnect the power cord from the wall 
socket if the projector will not be used in an 
extended period of time.
CAUTION
• To protect the lamp, the projector will not respond to any commands during the cooling 
process.
• To shorten the cooling time, you can also activate the Quick Power Off...

47
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
The menu items are available when the projector detects at least one valid signal. If there is 
no equipment connected to the projector or no signal detected, limited menu items are 
accessible.
Main menu Sub-menu Options
1. 
DISPLAY
Screen ColorOff/Blackboard/Greenboard/
Whiteboard
Aspect RatioAuto/4:3/16:9/
16:10 (PJD6543w only)/Wide  
(PJD6543w only)/Anamorphic...

48
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search Off/On
HDMI Format RGB/YUV/Auto
HDMI Range Enhanced/Normal
DynamicEco TimerDisable/5 min/10 min/15 min/30 
min
Smart Restart Off/On
Pattern Off/01/02/03/04/05
My ButtonProjection (Projector Position)/3D Sync/Lamp Mode/
DCR/Closed Caption/Auto Off (Auto Power Off)/
Message/Screen Color/CEC/Auto Search (Quick Auto 
Search)/Information
4.
SYSTEM
SETTING:
BASIC
Language Multi-language OSD selection
Projector PositionFront Table/Rear Table/Rear...

49
5. 
SYSTEM
SETTING:
ADVANCED
High Altitude Mode On/Off
DCR On/Off
Audio SettingsMute On/Off
Volume
Menu SettingsMenu Display Time5 sec/10 sec/15 sec/20 
sec/25 sec/30 sec
Menu PositionCenter/Top-Left/Top-
Right/Bottom-Left/
Bottom-Right
Closed CaptionClosed Caption Enable On/Off
Caption Version CC1/CC2/CC3/CC4
Lamp SettingsLamp Mode Normal/Economic
Reset Lamp Timer
Equivalent Lamp Hour
Presentation TimerTimer Period 1~240 minutes
Timer DisplayAlways/1 min/2 min/3 min/
Never
Timer...

50
Main menu Sub-menu Options
6. 
INFORMATIONCurrent System Status•Source
•Color Mode
•Resolution
•Color System
•Equivalent Lamp Hour
• MAC Address 

51
Description of each menu
Function Description
Screen ColorCorrects the projected picture’s color when the projection surface is 
not white. See "Using Screen Color" on page 32 for details.
Aspect RatioThere are several options to set the image's aspect ratio depending on 
your input signal source. See "Selecting the aspect ratio" on page 28
for details.
KeystoneCorrects any keystoning of the image. See "Correcting keystone" on 
page 27 for details.
Position
Displays the...

52
Function Description
Color ModePre-defined picture modes are provided so you can optimize your 
projector image set-up to suit your program type. See "Selecting a 
picture mode" on page 31 for details.
Reference 
ModeSelects a picture mode that most suits your need for the image quality 
and further fine-tune the image based on the selections listed on the 
same page below. See "Setting the User 1/User 2 mode" on page 32
for details.
BrightnessAdjusts the brightness of the image. See...

53
Function Description
Quick Auto 
SearchSee"Switching input signal" on page 25 for details.
HDMI FormatSee"Changing HDMI input settings" on page 25 for details.HDMI Range
DynamicEco
Timer
Allows the projector to decrease the power consumption automatically 
if no input signal is detected after a set period of time.
It takes some time to initiate this function. Make sure the 
projector has been turned on for more than 4 minutes.
Smart
Restart
Selecting On enables you to restart the...

54
Function Description
LanguageSets the language for the On-Screen Display (OSD) menus. See 
"Using the menus" on page 21 for details.
Projector
PositionThe projector can be installed on a ceiling or behind a screen, or 
with one or more mirrors. See "Choosing a location" on page 12 for 
details.
Auto Power 
OffAllows the projector to turn off automatically if no input signal is 
detected after a set period of time. See "Setting Auto Power Off" on 
page 58 for details.
Timer...

55
Function Description
High Altitude 
ModeA mode for operation in high altitude areas. See "Operating in a high 
altitude environment" on page 36 for details.
DCR
Enables or disables the DCR (Dynamic Contrast Ratio) function. 
Selecting On enables the function and the projector will 
automatically switch the lamp mode between normal and economic 
modes according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode...