ViewSonic Pjd6235 Projector User Manual

							36
Hiding the image
In order to draw the audience's full attention to the presenter, you can use   on the 
projector or Blank on the remote control to hide the screen image. Press any key on the 
projector or remote control to restore the image. The word 'BLANK' appears at the lower 
right corner of the screen while the image is hidden.
You can set the blank time in the 
SYSTEM SETTING: BASIC > Blank Timermenu to
let the projector return the image automatically after a period of time when there is no action 
taken on the blank screen. 
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to 
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from 
being changed accidentally (by children, for example). When the Panel Key Lock is on, no 
control keys on the projector will operate except POWER.
1. Press   on the projector or Lock on the remote control, or go to the 
SYSTEM 
SETTING: BASIC > Panel Key Lock menu
, and select On by pressing  /  on 
the projector or remote control. 
2. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, press and hold   on the projector or Lock  on the remote 
control for 3 seconds.
You can also use the remote control to enter the SYSTEM SETTING: BASIC > Panel 
Key Lock menu and press  /  to select Off.
• Keys on the remote control are still functional when panel key lock is enabled.
• If you press  POWER to turn off the projector without disabling panel key lock, the 
projector will still be in locked status the next time it is turned on.
Freezing the image
PressFreeze on the remote control to freeze the image. The word 'FREEZE' will be 
displayed in the upper left corner of the screen. To release the function, press any key on the 
projector or remote control.
Even if an image is frozen on the screen, the pictures are running on the video or other 
device. If the connected devices have active audio output, you will still hear the audio even 
though the image is frozen on screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500 
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature 
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under 
such a condition.
II
II 
						

							37
To activate the High Altitude Mode:
1. Press MENU/EXIT on the projector or Menu on 
the remote control and then press  /  until the 
SYSTEM SETTING: ADVANCED menu is 
highlighted.
2. Press  to highlight High Altitude Mode and 
press /  to select On. A confirmation 
message is displayed.
3. Highlight Yes and press MODE/ENTER on the projector or Enter on the remote 
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level 
because of increased fan speed necessary to improve overall system cooling and 
performance.
If you use this projector under other extreme conditions excluding the above, it may display 
auto shut-down symptoms, which is designed to protect your projector from over-heating. 
In cases like this, you should switch to High Altitude Mode to solve these symptoms. 
However, this is not to state that this projector can operate under any and all harsh or 
extreme conditions.
Using the CEC function
This projector supports CEC (Consumer Electronics Control) function for synchronized 
power on/off operation via HDMI connection. That is, if a device that also supports CEC 
function is connected to the HDMI input of the projector, when the projector’s power is 
turned off, the power of the connected device will also be turned off automatically. When 
the power of the connected device is turned on, the projector’s power will be turned on 
automatically.
To turn on the CEC function:
1. Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
2. Go to the SYSTEM SETTING: BASIC > CEC menu.
3. Press  /  to select On.
• In order for the CEC function to work properly, make sure that the device is correctly 
connected to the HDMI input of the projector via a HDMI cable, and its CEC function is 
turned on.
• Depending on the connected device, the CEC function may not work.
Using the 3D functions
This projector features 3D function which enables you to enjoy 3D movies, videos, and 
sporting events in a more realistic way by presenting the depth of the images. You need to 
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the 
signal for 3D Sync information and once detected, it projects images in 3D format 
automatically. In other cases, you may need to manually select a 3D Sync format for the 
projector to project 3D images correctly.
To select a 3D Sync format:
We recommend you use the High Altitude 
mode by selecting it whenever your 
environment is higher than 1500 m.
YesNoNotice
Do you want to turn High Altitude 
Mode ON? 
						

							38
1. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the DISPLAY menu is highlighted.
2. Press  to highlight 3D Settings and press MODE/ENTER on the projector or 
Enter on the remote control.
3. Press  to highlight 3D Sync and press MODE/ENTER on the projector or Enter
on the remote control.
4. Press  to select a 3D Sync setting according to the table below and then press 
MODE/ENTER on the projector or Enter on the remote control to confirm.
When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
• The Zoom can only magnify the pictures to limited sizes.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert” 
to correct the problem. 
						

							39
Controlling the projector through a LAN 
environment
The projector supports Crestron® software. With correct settings for the LAN Control 
Settings menu, you can manage the projector from a computer using a web browser when 
the computer and the projector are properly connected to the same local area network. 
Configuring the LAN Control Settings
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector 
and the other end to the RJ45 port.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the SYSTEM SETTING: BASIC menu is highlighted.
3. Press  to highlight LAN Control Settings and press MODE/ENTER on the 
projector or Enter on the remote control. The LAN Control Settings page is 
displayed.
4. Press  to highlight DHCP and press  /  to select On.
5. Press  to highlight Apply and press MODE/ENTER on the projector or Enter on 
the remote control.
6. Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings
page. The Projector IP Address,Subnet Mask,Default Gateway, and DNS Server
settings will be displayed. Note down the IP address displayed in the Projector IP 
Address row.
• If the Projector IP Address still does not appear, contact your network administrator.
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, 
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are 
properly connected and perform the procedures above again.
• If you need to connect to the projector in its standby mode, set Power Saving to Off.
If you are in a non-DHCP environment:
1. Repeat steps 1-3 above.
2. Press  to highlight DHCP and press  /  to select Off.
3. Contact your ITS administrator for information on the Projector IP Address,Subnet 
Mask,Default Gateway, and DNS Server settings.
(An example of connection) 
						

							40
4. Press   to select the item you want to modify and press MODE/ENTER on the 
projector or Enter on the remote control.
5. Press  /  to move the cursor and the press / to enter the value.
6. To save the settings, press MODE/ENTER on the projector or Enter on the remote 
control. If you do not want to save the settings, press MENU/EXIT on the projector 
orMenu on the remote control.
7. Press  to highlight Apply and press MODE/ENTER on the projector or Enter on 
the remote control.
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, 
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are 
properly connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected 
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS 
Server information when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby 
mode, you can use any computer that is on the same local area network to control the 
projector.
• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
• The screen shots in this manual are for reference only, and may differ from the actual 
design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
2. The main page of the Network Control appears.
Accessing to Network Settings or Email Alert page requires Administrator password. The 
default password is "0000".
3. This page allows you to make adjustments to the AMX and SNMP settings.  In the 
AMX device discover row, when ON is selected, the projector can be detected by 
5
4
3 
						

							41
controllers of AMX connected to the same network. For the Details of AMX Device 
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a network which supports Simple Mail Transfer 
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See 
"About Crestron e-Control®" on page 42 for details. 
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
Category ItemInput LengthMaximum Number 
of Characters
Network SettingsNetworkDHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
PasswordAdministrator (N/A)
New Password 4
Confirm Password 4
SNMPSysLocation 22
SysName 22
SysContact 22 
						

							42
 / > < $ % +   '  " are prohibited.
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projected pictures. 
i. These buttons function the same as the ones on the OSD menus or remote control. 
See"2. PICTURE menu" on page 52 and "Projector" on page 7 for details.
ii. To switch between input signals, click on your desired signal.
• The Menu button can also be used to go back to previous OSD menus, exit and save menu 
settings.
• The source list varies according to the connectors available on the projector.
• When you use the projector control panel or remote control to change the OSD menu 
settings, it may take a while for the web browser to synchronize these changes with the 
projector.
Email AlertEmail SettingTo 4 0
Cc 40
Subject 40
From 40
SMTP SettingServer 30
User Name 21
Password 14
Alert ConditionFan Error (N/A)
Lamp Error (N/A)
Over Temperature (N/A)
Lamp Time Alert (N/A)
Submit (N/A)
Issue Test Mail (N/A)
i
i
i
ii
You can press 
/ to reveal 
more buttons. 
						

							43
2. The tools page allows you to manage the projector, configure the LAN control 
settings and secure access of remote network operation on this projector.
i. This section is only used with the Crestron Control System. Please contact 
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of 
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been 
password-protected.
v. Once set, access to the tools page has been password-protected.
• To prevent errors, only input the English alphabet and digits on the tools page.
• After making the adjustments, press the Send button and the data will be saved for the 
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation 
keys) in the list blow:
Category ItemInput LengthMaximum Number of 
Characters
Crestron ControlIP Address 16
IP ID 4
Port 5
ProjectorProjector Name 32
Location 32
Assigned To 32
Network ConfigurationDHCP (Enabled) (N/A)
IP Address 16
Subnet Mask 16
Default Gateway 16
DNS Server 16
iiv
iii
ii
v
vi 
						

							44
3. The info page displays the information and status of this projector.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in 
the upper right corner of the screen. You will be able to deliver messages to 
RoomView™ software administrators/users who connect to the same local area 
network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s 
on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron 
control port.
About Crestron RoomView™ setting and command method, please access below website to 
get RoomView™ User Guide and more information: 
http://www.crestron.com/products/roomview_connected_embedded_projectors_devices/
resources.asp
User PasswordEnabled (N/A)
New Password 26
Confirm 26
Admin PasswordEnabled (N/A)
New Password 26
Confirm 26
Press Exit to 
go back to the 
remote network 
operation page. 
						

							45
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, 
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned 
on). To use these functions, be sure you have turned on the corresponding menus under 
SYSTEM SETTING: BASIC > Standby Settings, and the cable connections are correctly 
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 0.5W power consumption when Power Saving mode is turned on.
When Power Saving is On,  the network function is not available when the projector is in 
standby mode. 
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only 
from COMPUTER IN 1.
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN and AUDIO OUT sockets are 
correctly connected to devices.
Quick Power Off
Selecting On enables the function and the projector will not enter the cooling process after 
being shut down. Selecting Off disables the function and the projector will enter normal 
cooling process after being shut down.
• If you attempt to restart the projector right after it’s been turned off, it may not be turned 
on successfully and will rerun its cooling procedure.
• When Off is selected, the Smart Restart function will be automatically turned off.