ViewSonic Cde4200-l Manual
Here you can view all the pages of manual ViewSonic Cde4200-l Manual. The ViewSonic manuals for Display are available online for free. You can easily download all the documents as PDF.
Page 31
20 Sound Menu SOUNDSOUND Sound Settings A nalog Sound Stereo D igital Sound D igital A udio Output Off E qualizer Settings Off :Retur n:MoveMENUMENU:Go to Ne xt MenuENTERENTER SOUND SET TINGSSOUND SET TINGS Sound Mode Standar d B ass Tr eble B alanc e :Retur n:MoveMENUMENU:Change Setting Menu item Description Sound Settings Apply a preset audio option optimized for different sounding conditions (Standard / Soft / User / Dynamic). * If Sound Settings is set to User, you can adjust the following...
Page 32
21 Setup Menu SETUPSETUP Closed Caption M enu Language English Cloc k OSD Transparenc y Off OSD Timer 20 S :Retur n:MoveMENUMENU:Go to Ne xt MenuENTERENTER CL OSED CAPTIONCLOSED CAPTION Caption Displa y Off A nalog Caption Type CC1 :Retur n:MoveMENUMENU:On/O ff CLOCKCLOCK Setup Time 2012-08-18 11:41:17 Day of Week Sat Daylight Sa ving Time T ime Format 24H :Return:MoveMENUMENU:Change Setting Menu item Description Closed Caption Set Closed Caption (CC) settings. • Caption Display:...
Page 33
22 Hospitality Menu 1. Press MENU and 9, 9, 3 button on the remote controller to display the Hospitality menu. 2. Press or to select the menu item, then press or to adjust or select the setting. When selecting a menu item with a submenu ( > > ), press or ENTER to enter its submenu. 3. Press MENU to return to the previous menu or press EXIT to exit the menu. Hospitality Menu EEPROM Init Save Config To USB Load Config From USB Hospitality Hospitality Function DO OffMenu item Description...
Page 34
![Page 34
23
Other Information
Troubleshooting
Please contact ViewSonic service team directly if you have questions, se\
rvice needs,
or require technical assistance related on the use of your display.
Contact ViewSonic Service Team at:
http://www.ViewSonic.com
Or call our service team:
United States 1-800-688-6688
Canada 1-866-463-4775
Europe +44 (0) 207 382 8250
ProblemPossible Solution
No power •
Make sure the AC power cord is properly connected to the wall
outlet.
• Plug another electrical device (like a...](http://img.usermanuals.tech/thumb/80/97111/w300_d_1506429782-viewsonic-cde4200-l-manual_d-33.png "Page 34
23
Other Information
Troubleshooting
Please contact ViewSonic service team directly if you have questions, se\
rvice needs,
or require technical assistance related on the use of your display.
Contact ViewSonic Service Team at:
http://www.ViewSonic.com
Or call our service team:
United States 1-800-688-6688
Canada 1-866-463-4775
Europe +44 (0) 207 382 8250
ProblemPossible Solution
No power •
Make sure the AC power cord is properly connected to the wall
outlet.
• Plug another electrical device (like a...")
23 Other Information Troubleshooting Please contact ViewSonic service team directly if you have questions, se\ rvice needs, or require technical assistance related on the use of your display. Contact ViewSonic Service Team at: http://www.ViewSonic.com Or call our service team: United States 1-800-688-6688 Canada 1-866-463-4775 Europe +44 (0) 207 382 8250 ProblemPossible Solution No power • Make sure the AC power cord is properly connected to the wall outlet. • Plug another electrical device (like a...
Page 35
24 ProblemPossible Solution Unit cannot be operated • External influences such as lightning or static electricity may cause improper operation. In this case, operate the unit after first turning on the power of the display and the AV System, or unplug the AC cord for 1 to 2 minutes, then replug again. Power is cut off suddenly • Make sure the sleep timer is turned off. • Make sure the PC or video signal cable is connected properly. • The internal temperature of the unit has increased. Remove...
Page 36
25 Specifications ModelCDE4200-LCDE3200-L (LED Backlight) Screen Size 42-inch FHD 60Hz 32-inch FHD 60Hz Aspect Ratio 16:9 Input signal RGB 1 RGB analog (0.7/1.0 Vp-p, 75 ohms) Separate Sync, fh: 31.47-63.98 kHz, fv:59.8-70.09 Hz Video 1 composite RCA, 1 YPbPr component, 3 HDMI Audio 1 mini-stereo (for PC/VGA audio in), 1 pair of RCA (L/R) stereo USB JPEG / MP3 Format Compatibility PCUp to 1920 x 1080 (CEA mode) Speaker Output 10W x 2 @ THD=10% (max) Audio Output 1 Earphone jack, 1 SPDIF (optical) RS232...
Page 37
![Page 37
26
RS232 Protocol
1. Introduction
This document describes the hardware interface spec and software protoco\
ls of
RS232 interface communication between Viewsonic Commercial Display and P\
C or
other control unit with RS232 protocol.
The protocol divide into three sections:
• Set-Function
• Get-Function
• Remote control pass-through mode
※In below document, “PC” will represents all the control units that\
can sent or
receive the RS232 protocol command.
2. Description
2.1 Hardware specification...](http://img.usermanuals.tech/thumb/80/97111/w300_d_1506429782-viewsonic-cde4200-l-manual_d-36.png "Page 37
26
RS232 Protocol
1. Introduction
This document describes the hardware interface spec and software protoco\
ls of
RS232 interface communication between Viewsonic Commercial Display and P\
C or
other control unit with RS232 protocol.
The protocol divide into three sections:
• Set-Function
• Get-Function
• Remote control pass-through mode
※In below document, “PC” will represents all the control units that\
can sent or
receive the RS232 protocol command.
2. Description
2.1 Hardware specification...")
26 RS232 Protocol 1. Introduction This document describes the hardware interface spec and software protoco\ ls of RS232 interface communication between Viewsonic Commercial Display and P\ C or other control unit with RS232 protocol. The protocol divide into three sections: • Set-Function • Get-Function • Remote control pass-through mode ※In below document, “PC” will represents all the control units that\ can sent or receive the RS232 protocol command. 2. Description 2.1 Hardware specification...
Page 38
![Page 38
27
3. Protocol
3.1 Set-Function Listing
The PC can control the display for specific actions. The Set-Function co\
mmand
allows you to control the display behavior in a remote sit through the R\
S232 port.
The Set-Function packet format consists of 9 bytes.
Set-Function description:
Length:Total Byte of Message excluding “CR”
ID: Identification for each of display
If we want to set all settings, ID can use “99” to achieve, and it\
will not
have Reply command on this function.
The ID can be set via the...](http://img.usermanuals.tech/thumb/80/97111/w300_d_1506429782-viewsonic-cde4200-l-manual_d-37.png "Page 38
27
3. Protocol
3.1 Set-Function Listing
The PC can control the display for specific actions. The Set-Function co\
mmand
allows you to control the display behavior in a remote sit through the R\
S232 port.
The Set-Function packet format consists of 9 bytes.
Set-Function description:
Length:Total Byte of Message excluding “CR”
ID: Identification for each of display
If we want to set all settings, ID can use “99” to achieve, and it\
will not
have Reply command on this function.
The ID can be set via the...")
27 3. Protocol 3.1 Set-Function Listing The PC can control the display for specific actions. The Set-Function co\ mmand allows you to control the display behavior in a remote sit through the R\ S232 port. The Set-Function packet format consists of 9 bytes. Set-Function description: Length:Total Byte of Message excluding “CR” ID: Identification for each of display If we want to set all settings, ID can use “99” to achieve, and it\ will not have Reply command on this function. The ID can be set via the...
Page 39
![Page 39
28
Example2: Set Brightness as 176 for TV-02 and this command is NOT valid.\
Send (Hex Format)
Name
Length IDCommand Type CommandValue1Value2 Value3 CR
Hex
0x380x30
0x320x730x240x310x370x360x0D
Reply (Hex Format)
Name Length IDCommand Type CR
Hex
0x340x30
0x320x2D0x0D
Set-function table
Set Function LengthIDCommand
Type (ASCII) Command
Value Range
(Three ASCII bytes) Comments
Code (ASCII) Code (Hex)
Power on/off
(standby) 8
s!21000: STBY
001: ON
Input Select 8s“22000 : TV
001 : AV
002 : S-Video...](http://img.usermanuals.tech/thumb/80/97111/w300_d_1506429782-viewsonic-cde4200-l-manual_d-38.png "Page 39
28
Example2: Set Brightness as 176 for TV-02 and this command is NOT valid.\
Send (Hex Format)
Name
Length IDCommand Type CommandValue1Value2 Value3 CR
Hex
0x380x30
0x320x730x240x310x370x360x0D
Reply (Hex Format)
Name Length IDCommand Type CR
Hex
0x340x30
0x320x2D0x0D
Set-function table
Set Function LengthIDCommand
Type (ASCII) Command
Value Range
(Three ASCII bytes) Comments
Code (ASCII) Code (Hex)
Power on/off
(standby) 8
s!21000: STBY
001: ON
Input Select 8s“22000 : TV
001 : AV
002 : S-Video...")
28 Example2: Set Brightness as 176 for TV-02 and this command is NOT valid.\ Send (Hex Format) Name Length IDCommand Type CommandValue1Value2 Value3 CR Hex 0x380x30 0x320x730x240x310x370x360x0D Reply (Hex Format) Name Length IDCommand Type CR Hex 0x340x30 0x320x2D0x0D Set-function table Set Function LengthIDCommand Type (ASCII) Command Value Range (Three ASCII bytes) Comments Code (ASCII) Code (Hex) Power on/off (standby) 8 s!21000: STBY 001: ON Input Select 8s“22000 : TV 001 : AV 002 : S-Video...
Page 40
29 Number8s@40000~009 Key Pad 8sA41000: UP 001: DOWN 002: LEFT 003: RIGHT 004: ENTER 005: INPUT 006: MENU/EXIT Remote Control 8 sB42000: Disable 001: Enable 002: Pass through Disable: RCU has no effect on HDTV. Enabled: RCU controls the HDTV. This is the power up default on the HDTV. Pass through: RCU has no effect on HDTV and all RCU command codes are transmitted to FC via the RS232 port. Restore default 8 s~7E000 Resets HDTV to factory setting Note: 1. Behavior at lock modes Lock Mode...