Home > Uniden > Communications receiver > Uniden Receiver Bearcat BC235XLT Operating Instructions

Uniden Receiver Bearcat BC235XLT Operating Instructions

Here you can view all the pages of manual Uniden Receiver Bearcat BC235XLT Operating Instructions. The Uniden manuals for Communications receiver are available online for free. You can easily download all the documents as PDF.

Page 41

ID Hold Mode
During Search mode, you can hold on an ID without
entering it into memory.
1. Press
Hwhile in
Search mode.
2. Use the keypad to
enter the ID you want.
3. Press
Hagain.
HOLDflashes in the
display.
4. PressRto return to
Search mode.
Note:The ID Hold mode works in Scan List mode, and
the steps are the same; however,
SRCHdoesn’t
appear in the display.
12345678 910
12345678 910
41 

Page 42

ID Lockout
Like conventional scanning, it’s possible to lockout
unwanted traffic. This is particularly important in trunked
systems because in many areas water meters, door
alarms, traffic signals, and other mechanical devices are
assigned IDs just like other users. Also some departments
scramble or encrypt their communications, and you may
want to lock out these unintelligible broadcasts.
To lockout an ID,
press
Owhen the ID
displays.
The ID is locked out,
and the next active ID
displays. You can...

Page 43

Restore all IDs
To unlock all locked out IDs at once, follow these steps:
1. Press and hold
O
until you hear two
short beeps.
2. Press
Eto unlock all
the IDs at once.
Note:If you unlock all the IDs, then the Scan List
Memory mode displays. Press
Sto scan the IDs
stored in your Scan Lists or press
Rto return to
the Search mode. For information about Scan Lists
see page 46.
3. PressRto return to
the Search mode.
Searching Tips
ID Delay Mode
Use theYkey to select the Delay mode if it’s not
active. This mode...

Page 44

Hold Mode
PressHto hold on a particular ID in the display.
This is where the trunk tracking effect is really
noticeable. You can hold a specific talk group,
such as fire department on-scene operations, no
matter which frequency the group uses.
ID Monitor Mode
If you press and holdRuntil you hear two short
beeps, you will select the ID Monitor mode.
SRCH
begins flashing in the display, and all active talk
group IDs begin to display in succession. You
won’t hear conversations in this mode, but this is
an...

Page 45

nThe indicator which
remains on, even if
when there is no
traffic, represents the
frequency being used
as the data channel.
nIf an indicator turns
on and you don’t hear
a conversation, then
the channel is
probably being used
for a telephone
interconnect call or a
private call. These
calls are not
monitored by your
scanner.
nThe indicator which
flashes when an ID
displays represents
the frequency being
used by the talk
group.
nIf you’re holding on
an ID which isn’t
active, the activity
indicators will...

Page 46

Scan Lists
Each bank of yourBC 235XLTcan be a trunk tracking
bank or it can be a conventional scanning bank. When you
designate a bank as a trunking bank, your scanner sets up
5 Scan Lists, which are simply lists used to store your
favorite IDs. Each list can contain up to 10 IDs, so you can
store a total of 50 IDs for each trunk tracking bank (500 if
you use all banks as trunking banks!).
Scan Lists help you organize the trunking system users
into categories. For example, you might use List 1 for
police...

Page 47

4. Enter the Type II ID
you want to store,
and press
E.
—or—
To enter a Type I ID:
a. Enter the fleet
number.
b. Press
..
c. Enter the subfleet
number, and press
E.
Note:To clear a mistake while entering an ID,
press
.twice, and start over.
5. PressMor)to
select the next Scan
List location.
6. Press
Sto begin
scanning the lists you
have programmed.
If you haven’t
programmed any IDs,
SCANdisplays but
your scanner cannot
stop on an active
conversation.
7. To remove a Scan
List from active
scanning, press...

Page 48

8. To restore a Scan List
to active scanning,
press its number
again.
9. Press
Rto return to
Trunk Tracking
Search mode.
To alternate your
display between the
trunking repeater
indicators and the
Scan List indicators,
press
P.
Programming Scan Lists During Search
To select a Scan List location and store an ID during
Search mode, follow these steps:
1. When your scanner
stops on an ID you
want to store, press
P.
2. Use
)or(to select
the Scan List memory
location you want,
then press
E.
3. Press
Rto return...

Page 49

To let your scanner automatically store an ID in an
available Scan List location, follow these steps:
1. Press
Ewhen your
scanner stops on an
ID you want to store.
2. Press
Rto return to
Trunk Tracking
Search mode.
Deleting a Stored ID
To delete a stored ID:
a. Press
0.
b. Then press
E.
12345678 910
12345678 910
49 

Page 50

Fleet Map Programming
If you have programmed a trunk tracking bank and select
R, you will see user IDs display on your screen. Since
the
BC 235XLTdefaults to Type II systems, all the IDs
will appear as numbers. However, if you notice a mix of
odd and even user IDs, for example 6477, 2560, 6481,
6144, 1167, etc., then you are probably monitoring either a
Type I or Hybrid system. See
Types of Trunking Systems
on page 35.
You may also notice that you’re missing responses when
you hold on an active ID....
Start reading Uniden Receiver Bearcat BC235XLT Operating Instructions

Related Manuals for Uniden Receiver Bearcat BC235XLT Operating Instructions

All Uniden manuals