Trane Touchscreen Programmable Thermostat User Manual
Here you can view all the pages of manual Trane Touchscreen Programmable Thermostat User Manual. The Trane manuals for Thermostat are available online for free. You can easily download all the documents as PDF.
Page 11
BAS-SVX44A-EN11 Installation and Wiring Figure 1.Security screw removal and cover release 2. Push the cover thumb tab to release the cover from the backplate as shown above. 3. Route the wires through the opening in the backplate as shown below. Wires should be marked to ensure proper connection to terminals. Figure 2. Wire routing, mounting, and mounting dimensions 4. If mounting the backplate directly to a wall surface, hold the backplate against the surface andthen level and mark the fastener...
Page 12
12BAS-SVX44A-EN Installation and Wiring Wiring and Wiring Diagrams Wiring WARNING Hazardous voltage! Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power cannot be inadvertently energized. Failure to disconnect power before servicing could result in death or serious injury. NOTICE Equipment damage! Applying excessive voltage to the thermostat can permanently damage it. Note: Terminal blocks are included with the...
Page 13
BAS-SVX44A-EN13 Installation and Wiring Terminal Identification Table 3identifies the programmable thermostat terminals. Wiring Diagrams The following diagrams show typical wiring scenarios for the touch-screen programmable thermostat. UseTable 4and the corresponding figure to correctly wire the thermostat. Table 3. Terminal identification Connector TypeTerminal Label(a) (a) Label order above is how they appear on the thermostat terminal block. Terminal Description 8-pin Connectors Dh Dehumidify relay...
Page 14
14BAS-SVX44A-EN Installation and Wiring Figure 4. Programmable Thermostat, 1H/1C, Conventional (Option 1) Figure 5. Programmable Thermostat, 1H/1C, Heat Pump Without Auxiliary Heat (Option 2) Fa n24 VacC G Y W Rc R W2Y2 A S1 S2 Hp Hs Dh Heat Economizer/TOD Dehumidification Remote Humidity Sensor Remote Temperature Sensor Compressor L2 L1 (hot) Single Transformer: (jumper installed) Fa n L2 L1 (hot) 24 Vac Heat Compressor L2 L1 (hot) 24 Vac Cooling Transformer Heating Transformer Two Transformers:...
Page 15
BAS-SVX44A-EN15 Installation and Wiring Figure 6. Programmable Thermostat, 1H Only, Conventional Without Fan (Option 3) Figure 7. Programmable Thermostat, 1H, Conventional With Fan (Option 4) Figure 8. Programmable Thermostat, 1C, Conventional (Option 5) 24 Vac C G Y W Rc R W2Y2 A S1 S2 Hp Hs Dh Heat Economizer/TOD Dehumidification Remote Temperature Sensor Remote Humidity Sensor L2 L1 (hot) (jumper installed) Fa n 24 Vac C G Y W Rc R W2Y2 A S1 S2 Hp Hs Dh Heat Economizer/TOD Dehumidification Remote...
Page 16
16BAS-SVX44A-EN Installation and Wiring Figure 9. Programmable Thermostat, 2H/1C, Heat Pump With Auxiliary Heat (Option6) Figure 10. Programmable Thermostat, 2H/2C, Conventional (Option7) Fa n24 Vac Changeover Valve Compressor Auxiliary Heat L2 L1 (hot) (jumper installed) Economizer/TOD Dehumidification Remote Temperature Sensor Remote Humidity Sensor W1 Y2 A S1 S2 Hp Hs Dh C G Y O/B Rc R Fa n Heat 1 Heat 2 24 Vac C G Y W Rc R W2Y2 A S1 S2 Hp Hs Dh Economizer/TOD Dehumidification Remote Temperature...
Page 17
BAS-SVX44A-EN17 Installation and Wiring Figure 11. Programmable Thermostat, 2H/1C, Conventional (Option8) Figure 12. Programmable Thermostat, 1H/2C, Conventional (Option9) Fa n Heat 1 Heat 2 24 Vac C G Y W Rc R W2Y2 A S1 S2 Hp Hs Dh Economizer/TOD Dehumidification Remote Temperature Sensor Remote Humidity Sensor Compressor L2 L1 (hot) Single Transformer: (jumper installed) Fa n L2 L1 (hot) 24 Vac Heat 1 Compressor L2 L1 (hot) 24 Vac Cooling Transformer Heating Transformer Two Transformers: (jumper...
Page 18
18BAS-SVX44A-EN Installation and Wiring Figure 13. Programmable Thermostat, 2H/2C, Heat Pump Without Auxiliary Heat (Option10) Figure 14. Programmable Thermostat, 3H/2C, Heat Pump With Auxiliary Heat (Option 11) Thermostat Cover Replacement After completing all wiring, replace the thermostat cover. To replace the cover: 1. Hook the cover over the top of the backplate. Apply light pressure to the bottom of the cover until it snaps into place. 2. To help deter tampering, install the security screw into...
Page 19
BAS-SVX44A-EN19 Power, System Tests, and Software Reset This section provides information about: Applying power Power-up test System tests Applying Power Restore power to the HVAC equipment. The thermostat initiates a power-up test and will display an error, if one is detected (refer to the sections, “Power-up Test,” p. 19and“Error Codes,” p. 48 ). If no errors are detected, the home screen appears as shown in Figure 16. Figure 16. Home screens Power-up Test The power-up test is performed any time...
Page 20
20BAS-SVX44A-EN Power, System Tests, and Software Reset System Tests The system test mode is used to run diagnostics on the thermostat to verify that the unit is functioning properly. Referring to Table 6, p. 22, to run a system test: 1. Remove the thermostat cover as shown in the section, “Mounting the Backplate,” p.10. 2. Press and hold the Configurationbutton (refer toFigure17, p.21) for 3 seconds. The configuration/test icon ( ) displays and the thermostat is now in Configuration Setup Mode . 3....