Trane Comfort Link 2 Instruction Manual

       21 
6) Enter the Network Key using the on-screen keypad.5) Press “Enter Network Key” button.
2) Press the “Enter SSID Name” button.1) The “Network Security” button in this Ad-vanced Network Settings menu will be highlighted by default.
4) Select a network security type.*
     *NOTE:   WEP-Shared is not supported.
3) Enter the SSID Name using the on-screen keypad.
When the network’s SSID is not broadcast (hidden), manual configuration in this screen is required.
Network Security7.5 

22  
Host Settings7.6
This screen is used to manage how the control obtains network addresses and is needed when DHCP (Dynamic Host Configuration Protocol) has been turned off or is not available on the router.  Otherwise, you may use DHCP to automatically obtain this information.  This manual configuration is required if a static IP address is desired.
NOTE:  No additional configuration may be required in a non-broadcast network where IP addresses are assigned by DHCP.  You may connect to the network...

       23 
Once a network has been joined, the control will reconnect to it after signal or power interruptions.  When connected, a green dot will be shown.
To disconnect from this network, enter the “Connect to a Network” menu and select “Disconnect”.
NOTE:  When joining a different network, the current router must be discon-nected in this menu before a new one may be selected.  In addition if settings are changed on the owner’s router, the network may need to be disconnected and reconnected in this...

24  
Zoned and Multi-System Environments7.9
1) In a multi-system environ-ment each control can see and manage the others.  
 NOTE:  The controls must have wireless enabled and be connected to the same personal wireless network.
2) Each control belongs to an Access Control Group—set to “Group A” by default.  Therefore, if two controls are connected to the same wireless network and have matching Group IDs (shown as Group A to the right), they will be able to communicate with each other.
 Set the controls...

       25 
6) The Zone Overview menu shows a quick view of each zone’s current condition.
7) System wide settings for all zones can be seen at a glance in the System Status screen.
10) System and Zone Names may be set in the Zone Names screen.  The “Rename System” and “Rename Zone” buttons al-low entering custom names from a keypad.  
 Pre-configured names are also available.
8) A schedule for one zone can be copied to another.
5) In zoned and multi-sys-tem environments, the main screen display will...

26  
Wireless Registration8
1A) In the Network Setup Screen, select the “Register Now” button to begin registration.  Proceed to Step 2.
1B) If instead you try to connect to Weather before you have reg-istered, you will be prompted to register.
2) After reading and ac-cepting the License Agreement, enter your email address.
3) An email containing a verification code will automatically be sent to the email address you entered.
Registration is required for Weather, Software Updates and Schlage LiNK...

       27 
Schlage LiNK Enrollment9
10) After entering your verification code, your additional fea-tures will now be enabled.
11) In the event your email address changes, you can update the email ad-dress with your new one.  The process is similar to first-time registration.
9) Enter the 5-digit veri-fication code.
 NOTE:  This will only need to be done one time.
The control can be managed remotely via an internet connected computer and most smart cell phones via Schlage LiNK. Schlage is a leader in home...

28  
Software Upgrades10
Your control is built with the future in mind and has the ability to upgrade its operating system.  Software upgrades ensure your control has the most up-to-date software optimizing its opera-tion and providing exciting new features as they become available.
The Software Upgrades menu is accessed by navigating to Menu --> Settings --> Network.  After pressing the “Software Upgrades” button, follow the guided instructions on the series of screens.  
Upgrade the software by one of...

       29 
Troubleshooting11
Slow response or  
unexpected operation:
Reboot your control at the 
following location.
“No System Found” displays on the screen:
If this message stays on your screen, press the 
“Reboot” button shown at right.
No response to any button presses:
Remove and re-install the control as shown below.  The boot up process may take several minutes.
Re-Install Control Re-install control flat onto sub-base being careful to align unit correctly with the sub-base before applying force....

30  
Index of Functionality
1-Touch Presets ..................................14
Air Cleaner Mode ..................................7
Alerts ..................................................30
Customize Home Screen ....................15
Dealer Information ..............................13
Events .................................................13
Fan Mode..............................................6
Humidity ..............................................15
Multi-System...