Toshiba W-528 Manual

11
PREPARATION
Setting up the Remote Control
1Open the battery compartment lid on the
rear panel.
2Install 2 batteries (“AA” size) following
the polarity diagrams.
3Close the battery compartment lid.
4Point the remote control at the VCR and press the buttons within the operating range.
Distance: within about 7 m from the front of the remote sensor
Angles: within about 30˚ in every direction
Notes on batteries
•The life of the batteries is about 1 year
depending on the conditions of use.
•If the remote...

12
Antenna/VCR/TV Connection
1Disconnect the antenna cable from your TV and connect it to the RF IN terminal on the
VCR.
2Connect the RF OUT terminal to the TV.
AUDIO/VIDEO Connections
The AUDIO/VIDEO jacks are also available to connect your TV.
When connected your TV using the
AUDIO/VIDEO OUT jacks
To watch video pictures, set the video input mode
on your TV.  For the video input mode, refer to the
manual of your TV.
Setting the VCR Output Channel
When the VCR is connected in this way, the VCR sends the...

13
PREPARATION
This set-up will enable you to:
–watch an unscrambled or scrambled channel
while recording it.
–record any channels through the cable box.
You will need to:
•set TV channel 3 or 4 to receive video signals.
(See page 12).
•set VCR channel to the output channel of the
cable box, and select a desired cable channel
on the cable box.
•while the VCR is turned off or the “VCR”
indicator is not lit in the VCR display, set TV
channel to the output channel of the cable box.
This set-up will enable...

14
PREPARATION
Auto Set up
1Plug the VCR into the AC outlet
2“Auto” blink while the VCR automatically sets the clock using
the data broadcast by the local TV stations.
While “Auto” is blinking, channel memory is also set
automatically.
3When Auto set up has been completed, the VCR is on
standby mode.
Notes
•It may takes several minutes during the Auto set-up
•Press 
CANCEL on the remote control to cancel the auto set-up.
SLOWPAUSE /STILL
REC TIMER
TVVCRPOWER
I.SELECTSP/ SLPDISPLAY
TV VOL
COUNTER
PROG....

15
PREPARATION
Optional settings on the SET UP screen
Other optional settings can be made.  Press ENTER while “SET UP” is selected on the MENU screen.
The screen turns to the SET UP screen.
To exit, press 
PROG. once.
E n D  :    PROG
TAPE LEnGTH     120    160    180SAP  SET           on                 offCOUnTER MEM   on                 offLAnGUAGE      EnG    FRA     ESP
Setting the Language
1Press POWER to turn on the VCR.
2Press PROG..
The following screen appears on the TV.
4Press PROG. to return...

16
8Press ENTER to start the “AUTO” clock
set feature.
After the VCR is turned off, it automatically
updates the clock using the data broadcast
by the local TV stations.
*The clock is
  revised by
  broadcasting
  signal at 8:00 A.M
  every morning.
9Select the options using FF or REW.
Change the data using 
PLAY or STOP.
1) Set “SUMMER TIME
(Daylight-Saving Time)”.
DST start: Daylight-saving time begins on
the first Sunday in April. Because the
clock automatically changes from 2:00 AM
to 3:00 AM...

17
PREPARATION
Incoming Antenna/Cable(CATV) Signals
The VCR scans through all receivable TV and CATV channels and stores only the active
ones in your area into the memory.  Once the storing is finished, you can select a desired
channel using 
CH/TRK.
Preparation
•Turn on the TV, and select the video channel (3 or 4), or the video input mode if you made the Audio/Video
connection (page 12).
•Press 
I.SELECT so that the channel number will appear if “L1 / L2”( For W-528/W-522 only )  or
”L”( For W-422...

18
To add channels
To erase channels
3)Enter a channel number of 1 to 125 usingnumber buttons.
For more than 100 number, first press 
100.
For CATV channels, refer to the chart below.
(For other orders, check with your cable
company.)
4)Repeat steps 2) and 3) to add or erase
channels as necessary.
5)Press
 PROG. two times to exit.
Selecting stored channels
Once the active channels have been stored, you
can select the channels in two ways below.
Number buttons
To enter digits of the channel number.
•For...

19
PREPARATION
Video Cassette Use
Loading a cassette
Push the cassette into the cassette compartment with the window side facing up and the
label side towards the front.  The VCR is automatically turned on.  The            indicator will
appear in the VCR display.
Ejecting a cassette
Press EJECT.  The cassette is ejected from the cassette compartment.
Warning
Do not insert your hands or any foreign objects into the compartment.  This may result
in injury or damage.  Take special care with children to...

20
Adjusting the tracking
When playback starts, the VCR automatically adjusts the tracking for clear pictures and sound
(Digital Auto Tracking).
If the VCR cannot locate the best possible tracking point, hold down one of 
CH/TRK to adjust the
tracking manually.
Notes
• During the adjusting, the playback picture and sound may be distorted.
• The digital auto tracking is activated only in the playback mode.
• The noise on the screen may not be completely eliminated depending on the tape used, especially...