Toshiba W-528 Manual

							Video Cassette Recorder
W-528
W-522
W-422
OWNER’S MANUAL
SQPB
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 1 
						

							2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN
OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE
ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALI-
FIED PERSONNEL ONLY.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical.
Copyright
It is permissible to record television programs, film, video tapes and other material only
in the event that third party copyrights and other rights are not violated.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s en-
closure that may be of sufficient magnitude
to constitute a risk of electric shock to per-
sons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the literature
accompanying the appliance.
SAFETY PRECAUTIONS
Product Name: Video Cassette Recorder
Model Number: W-528/ W-522/ W-422
FCC Notice: “Declaration of Corformity”.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful Interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Contact: Toshiba America Consumer Products, Inc.
Address: 1420 Toshiba Drive, Lebanon, TN 37087
Telephone: 615-449-2360
User Installer Caution: Changes or modification made to this equipment not expressly approved by
Toshiba Corporation or parties authorized by Toshiba Corporation could void the user’s authority
to operate the equipment.
In the spaces provided below, record the Model and Serial No. located at the rear of your video
cassette recorder.
Model No. Serial No.
Retain this information for future reference.
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 2 
						

							3
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to ship
your VCR. For maximum protection, repack the set as it was originally packed at the factory.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit.
Do not leave rubber or plastic products touching the unit for a long time. They will mar the
finish.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the VCR is exposed to such a change in temperature, moisture may condense on the
cylinder inside, one of its most crucial internal parts. To prevent the VCR from possible
damage, do not use the unit for at least 2 hours when there is an extreme or sudden change
in temperature.
Compatibility
This video cassette recorder (VCR) is compatible with any other VCR bearing the 
mark. HQ VHS equipment is also compatible with existing, non-HQ VHS equipment.
As an ENERGY STAR  Partner, TOSHIBA has determined that this product or
product model meets the E
NERGY STAR   guidelines for energy efficiency.
®
®
INTRODUCTION
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 3 
						

							4
1.Read owner’s manual
After unpacking this product, read the owner’s manual carefully, and follow all
the operating and other instructions.
2.Power Sources
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating
instructions.
3.Grounding or Polarization
This product may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
4.Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure
reliable operation of the product and to protect it from overheating, and these
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface. This
product should not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s instructions have
been adhered to.
5.Heat
The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS
GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT.
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fire hazard. The safeguards incorporated in this unit will protect
you if you observe the following procedures for installation, use and servicing. This unit is
fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY.
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 4 
						

							5
6.Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and
the like.
7.Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
8.Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit from
the product.
9.Overloading
Do not overload wall outlets; extension cords, or integral convenience recep-
tacles as this can result in a risk of fire or electric shock.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
GROUND
CLAMPANTENNA
LEAD IN
WIRE
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
10.Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system
is grounded so as to provide some protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
11.Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
INTRODUCTION
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 5 
						

							6
16.Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen into the product.
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance - this indicates a need for service. 12.Lightning
For added protection for this product during storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
13.Object and Liquid Entry
Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
15.Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table.
The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product. Any mounting of
the product should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the product and cart
combination to overturn. 14.Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
17.Servicing
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
18.Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
19.Safety Check
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
S3125A
IMPORTANT SAFETY
INSTRUCTIONS
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 6 
						

							7
INTRODUCTION
Provides important notes and general
explanation of the VCR, including names of the
buttons, jacks, etc.
SAFETY PRECAUTIONS .................... 2
IMPORTANT PRECAUTIONS ............. 3
IMPORTANT SAFETY
INSTRUCTIONS ................................... 4
Contents .............................................. 7
Identification of Controls ................... 8
• Front Panel
• Remote Control
• VCR Display
• Rear Panel
PREPARATION
Explains what you need to do before operating
the VCR.
How to Use the Remote Control ...... 11
Connections ...................................... 12
Auto Set Up ....................................... 14
Initial Settings Using On-screen
Display ............................................... 15
• Setting the Language
• Optional settings on the SET UP
  screen
• Setting the Clock
Storing Channels on the VCR .......... 17
Video Cassette Use .......................... 19
PLAYBACK
Explains variable functions concerning
playback.
Playback ............................................ 20
• Basic Playback
• Double Speed Playback
• S-VHS Quasi Playback (SQPB)Variable Speed Playback ................. 21
• Picture Search
• Commercial Movie Skip
• Still Picture
• Frame Advance
• Slow-motion Picture
Useful Functions in Tape
Operation ........................................... 23
• Counter Function
• Tape Remaining Time
• Memory Stop Feature
RECORDING
Explains recording functions.
Recording a TV Program .................. 25
• Basic Recording
• Watching a TV program while
recording another
• Skipping unnecessary scenes while
recording
• Recording off time setting
Timer Program Recording ............... 26
MTS Broadcast Compatibility .......... 29
ADDITIONAL INFORMATION
Remote Control
for TOSHIBA TVs .............................. 30
Before Calling Service Personnel ... 31
Specifications ................................... 33
Accessories ...................................... 33
Memo.................................................. 34
LIMITED WARRANTY .............
Back cover
Contents
INTRODUCTION
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 7 
						

							8
Front Panel model  W-522
INTRODUCTION
Front Panel model  W-422
Front Panel model  W-528
Identification of Controls
See the page in  for details.
This manual shows the names of buttons in italics.
POWER
EJECT15
2520202020
2519Cassette compartmentREC
VCR Display
Remote  SensorCHANNEL
STOP PLAYFF
REW
15
25
2519
20202020
REC EJECT
CHANNEL
VCR Display
Cassette compartment
LINE IN 2 VIDEO jackLINE IN 2 AUDIO
(L/MONO, R) jacks
POWER
STOP PLAYFF
REW
Remote  Sensor
15
25
2519
20202020
POWERCassette compartmentREC EJECT
LINE IN 2 AUDIO
(L/MONO, R) jacks
LINE IN 2 VIDEO jack
CHANNELSTOP PLAYFF
REW
Remote
Sensor
VCR Display
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 8 
						

							9
VCR
TIMER
Hi-Fi
Remote Control
* These buttons are used to control the
   cursor on the screen.
To operate  your TV.
To operate this VCR.
SLOWPAUSE /STILL
REC TIMER
TVVCRPOWER
I.SELECT
SP/ SLPDISPLAY
TV VOL
COUNTER
PROG.
CANCEL
REMAIN/RESETCOUNT
EJECT
CM SKIP
30
20
20
22
18
19
15
123
654
10 0
9
8 7
0
STOP
FFREW
PLAY
ENTER
25
23
25
23
30
A.SELECT29
POWER
CH/TRK
CM SKIP 
100
ENTER
PLAY
 *
FF *
STOP *
PROG. CANCEL TIMER COUNT RESET SP/SLP PAUSE/STILL
TV VOLREC I.SELECT REMAIN/COUNTERDISPLAYSLOW REW 
*
EJECT PLAY
 *
A.SELECT(only for model W-528/W-522 ) 
Number buttonsVCRTV
20
15
18
20
20
15
15
20
21
25
23
27
28
25TV/VCR
21
Multifunctional
indicator VCR indicatorCassette indicator
Timer recording indicator
VCR Display
Hi-Fi  indicator
(only for model W-528/W-522)
INTRODUCTION
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 9 
						

							10
Rear Panel model W-528/W-522
L R
CH selector (3/4) LINE OUT AUDIO jacks (L, R)
LINE OUT VIDEO jack
RF IN (FROM ANT.) terminal
LINE IN 1 AUDIO jacks (L, R)
RF OUT (TO TV) terminal LINE IN 1 VIDEO jack
CHOUT(TO TV)
IN(FROM ANT.)LINE
OUTLINE
IN 1
VIDEO
AUDIO
34
RF
To wall outlet
Rear Panel model W-422
CH selector (3/4) LINE OUT AUDIO jack
LINE OUT VIDEO jack
RF IN (FROM ANT.) terminal
LINE IN AUDIO jack
RF OUT (TO TV) terminal LINE IN VIDEO jack
CHOUT(TO TV)
IN(FROM ANT.)OUT IN
VIDEO AUDIO
34RF
To wall outlet
LINE IN 1 AUDIO (Rear), 2 (Front) jacks
If the connected equipment is monaural (has one audio output jack), connect the L (MONO) side, the same
sound is recorded on both L and R on the Hi-Fi track.
W-528 522 422 eng (01-10)2/28/02, 2:27 PM 10