Toshiba Tec Bev4g Manual

1. OUTLINE EO18-33025 
  1.5 Supply Specifications
 
1-9 
1.5 Supply Specifications 
1.5.1 Media Type 
The table below shows the size and shape of the media that can be used on this printer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  Unit: mm (inch) 
Issue mode 
Item  Batch mode  Strip mode  Cut mode 
c
 Width including backing paper  25.4 to 112 (1.0 to 4.41) 
d Media width  22.4 to 109 (0.88 to 4.29) 
203 dpi  10 to 999 
(0.39 to 39.3)  25.4 to 152.4 
(1.0 to 6)  25.4 to 999 
(1.0 to 39.3) 
Label 
300 dpi  10 to...

1. OUTLINE EO18-33025 
  1.5 Supply Specifications
 
1-10 
NOTES: 
1.  To ensure print quality and print head life use only TOSHIBA TEC approved media. 
2.  When using a media roll of 76.2-mm (3”) inner core  diameter, the 3”-Diameter Media Shaft included in 
the optional External Medi a Roll Hanger is required. 
3.  Precaution for use of labels 
  When labels are used for printing,  please only use outside wound labels. 
  Use of an inside wound l abel causes a paper jam. 
  Outside wound  Inside wound...

1. OUTLINE EO18-33025 
  1.5 Supply Specifications
 
1-11 
The figure below shows the effective print area on the media. 
 
 
 
 
 
 
 
 
 
 
 
NOTES: 
1.  Be sure not to print on the 1.5-mm wide area  from the media edges (shaded area in the above figure). 
2.  The centre of media  should be positioned at the c entre of the print head. 
3.  Print quality is not guaranteed within 3 mm from  the print head stop position (including 1-mm slow-up.) 
4.  Average print (black) rate should be 15% or less....

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.1 Block Diagram
 
2-1 
2. ELECTRONIC SPECIFICATIONS 
2.1 Block Diagram 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.2 Main PC Board Layout
 
2-2 
2.2 Main PC Board Layout 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
JP9: USB 
JP3: Ethernet 
(10BASET/100BASETX)
JP2: SD Card Slot
JP4: Parallel (Centronics) 
JP7: Serial (RS-232C)
DC Jack
SW1: Power Switch
Ground Terminal
U2: 32bit RISC CPU
AT91SAM9260 
JP12: Print Head
GS model: 203dpi
U5: Flash ROMU6: SDRAM
JP14: Stepping Motor
U8: Ethernet Transceiver 
U12: Serial Interface Controller 
U18:...

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.3 Description of the Main PC Board
 
2-3 
2.3 Description of the MAIN PC Board 
This PC board, the brain of the printer, is comprised of the following components. 
 
32bit RISC CPU (U2):  Type: AT91SAM9260 
  The 32bit RISC CPU operates  the following processing: 
  Controlling the interfaces 
    • Serial Interface (RS-232C) 
    • Parallel Interface (Centronics) 
    • Eternet (10BASET/100BASETX) 
  Controlling the Status LED 
  Detect the [Feed] key...

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.3 Description of the Main PC Board
 
2-4 
DC/DC Converter (U22, 23):  Type: TS34063 
  It generates the voltages (+5V, +3.3V) from the power supply voltage 
(AC adapter). 
  +5V and +3.3V are used as the  operating voltage for each circuit. 
 
 
 
 
Eternet Transceiver (U8):  Type: DM9161 
  This IC is used for controlli ng the Ethernet (10BASET/10BASETX). 
 
 
 
Regulator (U24, U33):  Type: TS68N28CX5, TS9007DCX 
  It generates the voltages (+1.8)  from the...

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.3 Description of the Main PC Board
 
2-5 
JP2 (SD Card Slot):  Type: MS3B11-KAA-0 
  This connector is connected to the SD Card. 
  Note: Recommended SD card specification. 
 • Supported DOS FAT file system. 
 
•  Folders stored in the SD card should be in the 8.3 filename format. 
 
•  Approved SD card manufacturers: SanDisk, Transcend. 
 
SD V 1.0, V 1.1: 128MByte, 256MByte, 512MByte, 1GByte 
  SD V 2.0 (SDHC): 4GByte Class 6
 
 
 
 
 
 
 
 
JP3...

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.3 Description of the Main PC Board
 
2-6 
JP4 (Parallel Interfcae):  This connector is used for the Parallel (Centronics) interface. 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
JP7 (Serial Interface):  Type: D-Sub 9pin 
  This connector is used for t he Serial (RS-232C) interface. 
  +5V is output from the pin 1. 
  The TXD signal is a serial si gnal and output from the pin 2. 
  The RXD signal is a serial si gnal and input into the pin...

2. ELECTRONICS SPECIFICATIONS EO18-33025 
  2.3 Description of the Main PC Board
 
2-7 
JP9 (USB):  Type: Type B Connector 
  This connector is used for the USB interface. 
 
 
 
 
 
 
JP12 (Print Head):  This connec tor is connected to the print head (for GS model, 203dpi). 
  The voltages and signals for contro lling the print head are input/output 
into/from the connector. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Signal  Pin 
No. 
+5 V  1 
D- 2 
D+ 3 
N/C 4 
GND 5 
Signal  Pin 
No....