Toshiba Strata Vi Electronic Key Telephone System Installation And Maintenance Manual

maximum of 4 a~eess codes. 
X=1) to program first access 
as the second digit, 
If all combinations following a 
particular 1st digit are to be 
All LEDs off=No data 
All Ext. 17 LEDs (except MW/FE) go off 
key to advance to 
switch on the MCCU  

s on or 0 the LED is already on, pushing the 
key/LED represents itself-that is, if CO 
associated key will turn it off and 
1 LED is off, Toll Restriction will 
function on CO 1. If CO 1 LED is on, LEDs may be turned off and on until the 
Toll Restriction will not function on CO desired pattern is set 
line #l. 
. 
..OI”... 
LED on MCCU goes off 
New data is stored, previous data is erased  

Normal functions halt on Ext. I.7 
4 access codes. 
X=1) to program first access 
CO 4 dc 5 LEDs will light steadily to 
indicate which digit is being displayed 
RCD NO’S: 
* 
All LEDs off=No data 
key to advance to 
switch on the MCCU LED on IMCCU goes off 
Ext. 17 MIW  

numbered (18-25) stations are to be 
programmed simultaneously 
An X on the record sheet means the LED 
should be on 
eess allowed 
Each CO key/LED represents 
itself-that is, if CO 1 LED is on, 
station being programmed (XX) is 
allowed access to CO 1 If the LED is already on, pushing the 
associated key will turn it off and 
)ff and on switch on the MCCU  

system is in program mode 
Normal functions halt on Ext. 17 
SPMR LED steady on 
SPKR LED fla.shes continuously 
TNT & CO LEDs will be on according to 
if all stations are to be 
-17) stations are to be 
if the eight higher 
-25) stations are to be 
programmed simultaneously 
associated LEDs on or off as required. If the LED is already on, pushing the 
The detailed meaning of each key is associated key will turn 
it off and 
shown below, 
off and on until the 
Not Used 
. 
..0r... 
switch on the MCCU LED...

Ext. 17 MW/FL LED on 
System is in program mode 
Normal functions halt on Ext. 17 
CO 4, 5 & 6 LEDs will be on according 
to present data 
if all stations are to be 
if the eight lower 
-17) stations are to be 
if the eight higher 
-25) stations are to be 
An X on the record sheet means the LED 
should be on 
If the LED is already on, pushing the 
The detailed meaning of each key is associated key will turn it off and 
shown below. 
LEDs may be turned off and on until the 
More than 7 digits 
switch. on...

if all stations are to be 
if the eight higher 
numbered (18-25) stations are to be 
programmed simultaneously 
should be on 
eady on, pushing the 
meaning of each key is shown below. 
ill turn it off and 
LED on=Restricted outgoing calls 
Each CO key/LED represents 
LEDs may be turned off and on until the 
itself-tha.t is, if CO 1 LED is on, 
desired pattern is set 
the station being programmed (XX) is 
restricted from outgoing calls on 
co 1 
- 
in memory 
6A. Go to another program table 
. ..or......

number of the station 
CO LEDs will be on a 
if all stations are to be 
the eight lower 
7) stations are to be 
programmed simultaneously 
LEDs on or o 
If the LED is already on, pushing the 
associated key will turn it off and 
Each CO key/LED represents 
itself-that is, if CO 1 LED is on, 
LEDs may be turned off and on until the 
station being programmed (XX) will 
desired pattern is set 
ring when a call comes in on CO 1 
in the DAY mode 
switch on the MCCU 
LED on MCCU goes off 
OU power switch off...

if all stations are to be 
17) stations are to be 
numbered (U-25) stations are to be 
programmed simultaneously 
2. Refer to the System Record Sheet, he record sheet means the LED 
should be on 
If the LED is already on, pushing the 
Ing in DAY mode associated key will turn it off and 
Each CO key/LED represents 
itself-that is, if CO 1 LED is on, 
LEDs may be turned off and on until the 
station being programmed (XX) will 
desired pattern is set 
ring when a call comes in on CO 1 
in the NITE mode....

s