Toshiba Strata Vi Electronic Key Telephone System Installation And Maintenance Manual

No Restriction 
a 
. 
Restrict: “0” in 1st o 2nd digit 
11 1 11 in 2nd digit 
#Iore than 7 digits total 
Al low: 911 and 800 
Exception Codes-Program 2X* 
rrl” + 7 digits 
411 
* 
e 
Restrict: “0” in 1st 2nd digit 
“1” in 2nd digit 
LVlore than 7 digits total 
Al low: 911 and 800 
Exception Codes-Program 2X* 
“1” + 7 digits 
. 
. 
Restrict: “0” in 1st 2nd digit 
If 1 (1 
in 1st 2nd digit 
More than 7 digits total 
Allow: 911 and 800 
Exception Codes-Program 2X* 
Restrict: “0” in 1st 
2nd digit 
rrllf in...

To initialize the STRATA VI 
system: 
Make sure the MTOU power switch 
is in the position, 
Verify that the battery is eon- 
neeted on the MCCU (and C 
equipped) to ensure that data en- 
tered after system initialization 
will not be lost due to power 
failure. The SET LED on the 
MCCU XI not function if the 
the not 
connected. 
Hold in the 
epress and release the 
again. 
Release the switch. 
he MTOU power switch 
The system is initialized. 
The Aiatomatic Dialing memory 
will contain random numbers...

be made and select the required 
program number. Refer to the proper 
table for detailed instructions for using 
each different program. Each program 
should be accomplished sequentially until all necessary changes are made. 
The table numbers for the 
various programs are: 
e 
Initialized Data 
- 
System Assignments (Basic) 
01 
System Assignments (Options) 
02 
Automatic Recall from Hold Timing 
05 
AROH Disable 
06 
ARQH Timing 
07 
PBX Backup 
10 
PBX Access Codes 
1X 
Toll Restriction Disable 
20...

Toll Restriction Exception Codes- 
-2X Program 
No Codes Assigned 
Station CO Line Access-3XX Pro- 
gram 
4ccess Allowed-all 
lines, all 
stations 
Station Class of 
Service--5XX 
Program 
All Call-include all stations 
.4utomatic Line Preference-en- 
able all stations 
Automatie Dialing-allowed 
all 
stations Speakerphones-allowed all stations 
DND Override-not allowed all 
stations 
Privacy Override-not allowed all 
stat ions 
Toll Restriction Class-6XX Program 
No 
Restrictions-all lines, all...

keys, turn the 
1s already on, pushing the 
The detailed meaning of each key/LED is associated key will turn it off and 
shown below. 
LEDs may be turned off and on until the 
desired pattern is set 
All Ext. 17 LEDs (except MN/FL) go off 
-or... 
and on  

Ext. 17 MWIFL LED on 
System is in program mode 
to present data 
An X on the record sheet means the LED 
should be on 
associated LEDs on or off as required. 
If the LED is already on, pushing the 
The detailed meaning of each key/LED is 
associated key will turn it off and 
shown below. 
LEDs may be turned off and on until the 
desired pattern is set 
0 
m 
* e 
All Ext. 17 LEDs (except MW/FL) go off - 
and on 
New data is stored, previous data is erased  

4. Refer to the System Record Sheet. 
Using the 
and 
keys, turn the 
associated LEDs on or off as required. 
The detailed meaning of each key/LED is 
shown below. 
6A. Go to another program table 
- 
. ..or 
6B. Operate switch on the MCCU an 
eycle the power switch on the MTOU off 
and on to present data 
An X on the record sheet means the LED 
should be on 
Hf the LED is already on, pushing the 
associated key will turn it off and 
vice-versa 
Only one LED is allowed to be on 
All Ext. 11 LEDs (except...

Ext. 17 MW/FL LED on 
System is in program mode 
Normal functions halt on Ext. 17 
e on accordin 
e associated 
that line. 
-or... 
New data is stor  

s, turn the associated 
already on, pushing the 
ill turn it off and 
timing for AROH. If CO 1 LED is off, LEDs may be turned off and on until the 
ESS timing will be used on that line. desired pattern is set 
(except XIW/EL) go off 
and on 
stored, previous data is erased  

Normal functions halt on Ext. 17 
CO LEDs will be on accordin 
e associated 
should be on 
LEDs on or off as required. Each CO 
If the LED is already on, pushing the 
associated key will turn it off and 
1 line is connected to a PBX line and 
LEDs may be turned off and on until the 
will cause features such as Toll 
desired pattern is set 
Restriction and Automatic Dialing to 
function accordingly. 
switch on the MCCU 
LED on MCCU goes off 
New data is stored, previous data is erased