Toshiba Strata Vi Electronic Key Telephone System Installation And Maintenance Manual

The STRATA VI operating sys- 
tem governing overall system operation 
and feature execution is stored in read- 
only-memory (ROM) and cannot be al- 
tered in the field. The data con- 
trolling the operation of the various 
options, both system and station, is 
stored in random-access-memory (RAM) 
and can easily be changed according to 
individual installation requirements. 
All STRATA VI options are 
oiled by selections made in the 
system data tables. An initialization, 
process is provided for...

Type 2 program-data is entered 
via the dial pad. The LEDs on 
Ext. 17 will display the data and 
digit number in BCD format. 
Once the desired data is 
entered and displayed it 
en into 
memory by operating the key on 
Ext. 17. When the key is 
depressed, the data is either written 
into a temporary storage location or 
the main data memory. 
System and CO line options are 
written in to temporary storage 
key is depressed. 
s in these cate- 
een made, release the 
switch on the MCCU. All 
data is then...

. 
Six options a lected this pro- 
gram, using and keys to 
change the status of their respective 
LEN, For the options selected, mark 
an “X1’ as indicated I) 
Extension lo-mark an X next to 
CO 6 if Ext., 10 is to be used as 
the message waiting center. 
Extension ll-mark an X next to 
CO 5 if Ext. 11 is to be used as 
the message waiting center. 
3-second Pause Time-mark an X 
next to CO 2 if a S-second pause 
(for dial tone delay) is required 
after a PBX CO access code is 
dialed by the Automatic...

Selects whether or not the ilutomatic 
Release on Hold (AROH) feature is to 
fttnction on a given CO line; the CO 
line keys represent themselves. 
Mark an X next to each CO line 
Selects Cross Bar (XB) cbr ESS timing 
for the AROH feature using each CO 
line key to represent itself. 
Mark an X next to each CO line 
that requires XB timing; leave 
blank if ESS timing is required. 
Informs the system if the CO line key 
is actually connected to a PBX exten- 
sion line. The system will recognize 
PBX...

CO line that 
by 
the station in 
Seven options are selected with this 
program by using the and 
keys to change the of 
respective LED% The selections listed 
below must be repeated for each 
station. In all cases, mark an X where 
indicated. 
Privacy Override--mark an X next 
to CO 6 if the station 
the Privacy Override feat 
DND Override-mark an X next to 
CO 5 if the station 
the 
DND averride feature. 
20-key EKT-mark an X next to 
CO 3 if the station 
with a 20-key EKT, 
Speakerphone-mark an X next...

Selects which CO line will ring at a 
given station when the system is in the 
‘~NI’l’E*~ mode. 
Selections must be made for each 
station--mark an X next to each CO line that 
station in question. at the  

*Message Waiting Center 
X=Select (LED on> 
Initialized Data: All LEDs off except CO 6 
X=Select (LED on) 
Initialized Data: All LEDs off except CO 6 
X=Select (LED on) 
Initialized Data: 32 seconds  

X=enable (LED on) 
Initialized Data: 
A.11 LEDs off X=XB (LED on> 
Blank=E§S 
Initialized Data: 
All LEDS off 
X=Connected to PBX Line (LED on> 
Init, Data: All LEDs off 
I Enter Access Codes (Max: 4) 
Initialized 
Data: None 
X=disable (LED on) 
hit, Data: All LEDs off  

Initialized Data: None 
X=select (LED on) 
Initialized Data: All LEDs on 
X=select (LED on) 
Initialized Data: CO 1 & 2, INT 1 & 2 LED on; all others off  

1,O 1st digit 
I,0 2nd digit 
X=Select (LED on) Init. Data: No Restriction 
tricted 
tricted 
tricted 
- .- ,_ -_ - I i I I 1 i t t i i 
X=seleet (LED on) Initialized Data: A11 EEDs off 
X=select (LED on) Init. Data: Ext l&all on; all others off 
X=select (LED on) Init. Data: Ext 1P-all on; all others off