Toshiba Satellite 1100 Manual

							191
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
If you are using the built-in screen, make sure the display 
priority is not set for an external monitor. To do this, press Fn 
and F5 simultaneously (once). If this does not correct the 
problem, press Fn and F5 simultaneously again to return the 
display priority to its previous setting.
If you are using an external monitor:
❖Check that the monitor is turned on.
❖Check that the monitor’s power cable is firmly plugged 
into a working power outlet.
❖Check that the cable connecting the external monitor to 
the computer is firmly attached.
❖Try adjusting the contrast and brightness controls on the 
external monitor.
❖Press Fn and F5 simultaneously to make sure the display 
priority is not set for the built-in screen.
The screen does not look right.
You can change the display settings by clicking a blank area 
of the desktop with the secondary control button, then 
clicking Properties. This opens the Display Properties dialog 
box. The Appearance tab of this dialog box allows you to 
choose the colors for the screen. The Settings tab allows you 
to choose the screen resolution.
The built-in screen flickers.
Some flickering is a normal result of the way the screen 
produces colors. To reduce the amount of flickering, try using 
fewer colors.
To change the number of colors displayed:
1Point at the desktop and click with the secondary button.
2Click Properties, and then the Settings tab.
3Choose a lower quality color option and click OK.
For more information, see Windows
® Help. 
						

							192
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
A message tells you that there is a problem with your 
display settings and that the adapter type is incorrect or 
the current settings do not work with your hardware.
Reduce the size of the color palette to one that is supported by 
the computer’s internal display.
To change the display properties:
1Point at the desktop and click with the secondary button.
The Display Properties window appears.
2Click Properties, then click the Settings tab.
3Adjust the screen resolution and/or color quality.
4 Click OK.
The display mode is set to Simultaneous and the external 
display device does not work.
Make sure the external monitor is capable of displaying at 
resolutions of 800 x 600 or higher. Devices that do not 
support this resolution will only work in Internal/External 
mode.
Disk drive problems 
Problems with the hard disk or with a diskette drive usually 
show up as an inability to access the disk or as sector errors. 
Sometimes a disk problem may cause one or more files to 
appear to have garbage in them. Typical disk problems are:
You are having trouble accessing a disk, or one or more 
files appear to be missing.
Make sure you are identifying the drive by its correct name 
(A: or C:).
Error-checking
Run Error-checking, which analyzes the directories, files and 
NT file system (NTFS) on the disk and repairs any damage it 
finds:  
						

							193
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
To run Error-checking:
1Click Start, then click My Computer.
2Right-click the drive you want to check.
The drive’s properties box appears.
3Click on Properties.
4Click the To o l s tab.
5Click the Check now button.
The Check Disk box appears (for example, Check Disk 
C).
6You can choose one or both options:
❖Automatically fix file system errors
❖Scan for and attempt recovery of bad sectors
❖Click Start.
Error-checking runs the test.
Your hard disk seems very slow.
If you have been using your computer for some time, your 
files may have become fragmented. Run Disk Defragmenter. 
To do this, click Start, point to All Programs, Accessories, 
System To o l s, and click Disk Defragmenter.
Your data files are damaged or corrupted.
Refer to your software documentation for file recovery 
procedures. Many software packages automatically create 
backup files.
You may also be able to recover lost data using utility 
software, which is available from your dealer.
Some programs run correctly but others do not.
This is probably a configuration problem. If a program does 
not run properly, refer to its documentation and check that the 
hardware configuration meets its needs. 
						

							194
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
A diskette will not go into the external diskette drive.
You may already have a diskette in the drive. Make sure the 
drive is empty.
You may be inserting the diskette incorrectly. Hold the 
diskette with the hub side facing down, and insert it so that 
the metal head window cover goes into the drive first.
The metal cover or a loose label may be obstructing the path 
into the drive. Carefully inspect the diskette. If the metal 
cover is loose, replace the diskette. If the label is loose, 
replace the label and try inserting the diskette again.
The computer displays the Non-system disk or disk error 
message.
If you are starting the computer from the hard disk, make sure 
there is no diskette in the diskette drive. If there is, remove it.
If you are starting the computer from a diskette, the diskette 
in the drive does not have the files necessary to start the 
computer. Replace it with a bootable diskette and restart the 
computer.
For information on how to make a bootable disk, refer to your 
Windows
® booklet.
The drive cannot read a diskette.
Try another diskette. If you can access the second diskette, 
the first diskette (not the drive) is probably causing the 
problem. Run Error-checking on the faulty diskette (for 
instructions, see “Disk drive problems” on page 192).
DVD-ROM drive problems
You cannot access a disc in the drive.
Make sure the drive tray has closed properly. Press gently 
until it clicks into place.
Open the drive tray and remove the disc. Make sure the drive 
tray is clean. Any dirt or foreign object can interfere with the 
laser beam. 
						

							195
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
Examine the disc to see whether it is dirty. If necessary, wipe 
it with a clean cloth dipped in water or a neutral cleaner.
Replace the disc in the tray. Make sure it is lying flat, label 
side uppermost. Press the disc down until it locks on the 
spindle. Close the drive tray carefully, making sure it has shut 
completely.
You press the disc eject button, but the drive tray does 
not slide out.
Make sure the computer is connected to a power source and 
turned on. The DVD-ROM drive eject mechanism requires 
power to operate.
To remove a disc without turning on the computer, use a 
narrow object, such as a straightened paper clip, to press the 
manual eject button. This button is in the small hole next to 
the disc eject button on the right side of the computer.
CAUTION: Never use a pencil to press the manual eject button. 
Pencil lead can break off inside the computer and damage it.
Pull the tray fully open, remove the disc and place it in its 
Some discs run correctly, but others do not.
If the problem is with an application CD-ROM, refer to the 
software’s documentation and check that the hardware 
configuration meets the program’s needs.
The color of the materials used to make the disc can affect its 
reliability. Silver-colored CD-ROMs are the most reliable, 
followed by gold-colored CD-ROM. Green-colored CD-
ROMs are the least reliable.
WinDVD problems: General issues
WinDVDTM has been configured to provide optimum 
performance and quality based upon your system’s available 
resources. Changes made to the system or its configuration  
						

							196
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
may impact the playback performance of the WinDVD 
player.
WinDVD controls are disabled.
Controls may be grayed out by commands on the DVD. For 
example, it is common for DVD movie titles to disable fast-
forward and rewind during the legal notices at the beginning 
of a movie.
Playback performance is poor.
The use of DMA dramatically increases the DVD playback 
performance of your system.
To make sure DMA is turned on and to check its settings:
1Click Start, then Control Panel.
2Click the Performance and Maintenance icon, then 
click the System icon.
3Click Hardware tab, then the Device Manager button.
4Double-click IDE ATA/ATAPI controllers to expand it, 
then double-click Secondary IDE Channel.
The Properties Box appears. 
5Select the Advanced Settings tab, then select DMA if 
available from the Transfer Modes drop-down list. In 
the correct device area, click OK.
6The system must be restarted for this setting to take 
effect.
The Root or Title menu does not open.
Most DVD titles have one or both of the “Root” and “Title” 
menus. If one menu button appears to do nothing, try the 
other menu button.
WinDVD performance decreases after making a system 
change.
DVD playback performance is dependent upon several 
system resources. Changes to these system resources caused,  
						

							197
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
for example, by installing a new graphics or audio card may 
impact performance. Some software changes may also 
impact playback performance (for example, downloading 
new drivers from the Web). 
Before installing a new hardware or software component on 
your system, check for any potential conflicts between its 
resource requirements and your current system configuration. 
Also, if you change your operating system, check with your 
PC manufacturer or your graphics card vendor to ensure that 
you have the appropriate drivers for both your hardware (for 
example, the graphics card) and software (drivers must 
support the operating system and DVD with WinDVD).
Slow playback performance.
DVD playback is a resource intensive application. Other 
applications and/or changes to your system hardware, 
software or configuration can impact playback performance. 
If playback is slower than normal, try:
1Closing any other open applications to improve the 
performance of the DVD playback. 
2Ensuring DMA is turned on. (See “Playback performance 
is poor.” on page 196.)
3If you have installed new hardware (such as a new 
graphics card or audio card), ensure the component’s 
drivers support Microsoft
® DirectX® 5.2b or higher and 
WinDVD. Contact the manufacturer of the component.
4Verifying that your display driver resolution, color depth 
and refresh rate are optimal for DVD playback. (Some 
systems do not support video overlays if these parameters 
are not optimal.) Try lowering these settings to improve 
performance. 
						

							198
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
WinDVD problems: Content issues
Movies exhibit poor performance of “Directors 
Commentary” or other similar optional content 
versions.
Some movies may exhibit poor performance of these 
features. In particular, the video portion of the movie may 
become jerky or show pauses. The normal version of the 
movie will not show this problem.
WinDVD will not function properly with “debug” 
software installed.
The WinDVD application will not function properly if it 
detects that debug software is present on the system. Remove 
the debug software to restore functionality of WinDVD.
Minimum system requirements
WinDVD performs best when these recommended 
components are present in your system:
❖Sound card (with 48 KHz sampling rate support) 
❖DirectX® Foundation 6.0 or higher (Source: Microsoft) 
❖DirectShow® 6.0 (Source: Microsoft) 
❖DVD-ROM drive with DMA enabled (only available 
with Microsoft OSR 2.1 or above with PIXX 4.0 and 
USB support added) 
❖WinDVD software  
						

							199
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
WinDVD: Error messages
This table offers descriptions and resolutions for error 
messages that may appear when using WinDVD. 
Error message and additional 
informationResolution
The disc in the DVD-ROM 
drive is not a valid disc 
type.
Valid disc types are 
DVD-Video and audio CD.Ensure the disc is a valid 
disc type.
If the disc works in other 
players, try using a disc 
cleaner.
The disc may require fea-
tures that are not supported 
by WinDVD.
Microsoft
® DirectShow® 
components are missing.
Microsoft
® DirectShow® is 
not installed properly on the 
system.Reinstall Microsoft
® 
DirectShow® version 6.0 or 
higher (available from the 
Microsoft Web site).
No audio subsystem could 
be found for playback.
There is a problem with the 
audio card or audio compo-
nent within the system. The 
problem may be one of the 
following:
The audio card is faulty.
There is a problem with the 
audio driver.Check installation of the 
sound card drivers. 
						

							200
If Something Goes Wrong
Resolving a hardware conflict
5.375 x 8.375 ver 2.3
WinDVD cannot display 
the selected resolution due 
to system limitations.
The screen size exceeds the 
allowable display limit. 
There are not enough sys-
tem resources to play the 
DVD at the selected setting.Alter the display settings to 
reduce the resolution or 
number of colors.
Update video drivers.
The audio settings are 
incorrect. Please check 
sound card or drivers.
The audio card was found, 
but there is a problem with 
the audio card or drivers. 
The wrong audio driver 
may be installed in the sys-
tem.Check installation of the 
audio card drivers.
An unexpected error has 
occurred.
This error is unclassified. 
Report the problem and any 
error code to your suppliers 
Technical Support.This is usually a rare, 
title-specific problem. Error message and additional 
informationResolution