Toshiba Projector Tlp X4100u User Manual

11
PREPARATION
POSITIONING PROJECTOR
●This projector is designed to project on a flat
projection surface.
●Projector can be focused from 4.6’ (1.4m) ~ 48.3’
(14.7m).
●Refer to figure below to adjust screen size.
Screen
Size
Distance40”
31”
4.6’ (1.4m)
40”
4.6’(1.4m)11.8’(3.6m)24.0’(7.3m)36.1’(11.0m)
Max. Zoom
Min. Zoom48.3’(14.7m)100”200”300”400”
308”
231”
154”
77”
31”
ROOM LIGHT
Brightness in room has a great influence on
picture quality. It is recommended to limit
ambient lighting in order to provide...

12
PREPARATION
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
●Do not drop or bump a projector, otherwise damages or malfunctions may result.
●When carrying a projector, use a suitable carrying case.
●Do not transport a projector by using a courier or transport service in an unsuitable transport case.  This
may cause damage to a projector.  To transport a projector through a courier or transport service, consult
your dealer for best way.
MOVING PROJECTOR
Use Carry Handle when moving a Projector.
When...

13
S–VIDEO
R–AUDIO–L VIDEO/Y Cb/Pb    Cr/PrVIDEO/Y Cb/Pb Cr/Pr
RESETCONTROL PORT USBAUDIO 1 AUDIO 2ANALOG DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3
R/C JACK
GB RH/V V
(
MONO)
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
When controlling computer
with Remote Control Unit of
this projector, connect mouse
port of your personal computer
to this connector.  (Refer to
P14.)
Connect S-VIDEO
output from video
equipment to this
jack.  (Refer to P15.)  
Connect an audio output
(stereo) from computer to
these jacks....

14
S–VIDEO
R–AUDIO–L VIDEO/Y Cb/Pb    Cr/PrVIDEO/Y Cb/Pb Cr/Pr
RESETCONTROL PORT USBAUDIO 1 AUDIO 2ANALOG DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3R/C JACK
GB RH/V V
(
MONO)
ON
1DIPON
OFF
23456
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF ON ON
ON ON
ON ONOFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF1234 56
OFF OFF ON ON ON ON 21 MODE (1152 x 870)
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
VGA Cable Monitor Output...

15
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
S–VIDEO
R–AUDIO–L VIDEO/Y Cb/Pb    Cr/PrVIDEO/Y Cb/Pb Cr/Pr
RESETCONTROL PORT USBAUDIO 1 AUDIO 2ANALOG DIGITAL(DVI-D)
INPUT 1
INPUT 2
INPUT 3R/C JACK
GB RH/V V
(
MONO)
Video Source (example)
Video Cassette Recorder Video Disc Player
S-VIDEO
Cable ✽
Terminals 
of a Projector
S-VIDEO Output
Cables used for connection(✽= Cable is not supplied with this projector.)
• Video Cable (RCA x 1 or RCA x 3) 
✽
• BNC Cable ✽
• S-VIDEO Cable ✽
• Audio Cable (RCA x...

16
BEFORE OPERATION
VOLUME
ON-OFF
FOCUS
ZOOM
D.ZOOM
MENUMUTE
LASER
KEYSTONE
NO SHOWFREEZE
AUTO PC ADJ.IMAGE
P-TIMER
LOCK
INPUT
LENS SHIFT
OPERATION OF REMOTE CONTROL
ON
ALL OFF
ALL-OFF SWITCH
Left Side
When using Remote Control Unit,
turn this switch to “ON.”  And turn it
to “ALL OFF” when it is not used.
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window.  When LASER button is
pressed, laser light goes on.  And when LASER button is being pressed for more than 1...

17
BEFORE OPERATION
To insure safe operation, please observe following precautions :
●Use (2) AA, UM3 or R06 type alkaline batteries.
●Replace two batteries at same time.
●Do not use a new battery with an used battery.
●Avoid contact with water or liquid.
●Do not expose Remote Control Unit to moisture, or heat.
●Do not drop Remote Control Unit.
●If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
●Danger of explosion if battery is incorrectly replaced....

18
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
Used to open or close
MENU operation. (P19,
20)
MENU BUTTON
IMAGE BUTTON
READY INDICATOR
SELECT BUTTON
POWER ON–OFF BUTTON
INPUT BUTTON
WARNING TEMP. INDICATORLAMP INDICATOR
POINT (VOLUME + / – ) BUTTONS 
LAMP REPLACE INDICATOR
Used to select image
level.  (P29, 34)
Lights  green when  a
projector is ready to be
turned on.  And it
flashes green in Power
Management mode.
(P38)Becomes dim when a
projector is turned on.
And bright when a
projector is in...

19
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR).  A red frame is POINTER.
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.
Press POINT DOWN button and move POINTER (red frame
or red arrow) to ITEM that you want to adjust, and then press...

20
BEFORE OPERATION
MENU BAR
PC SYSTEM MENU
Used to select
computer system.
(Refer to P24, 25)
IMAGE ADJUST MENU
Used to adjust
computer image. 
[Contrast / Brightness
/ White Balance
(R/G/B) / Gamma]
(Refer to P30)
SETTING MENU
Used to change
settings of projector
or reset Lamp
Replace Counter. 
(Refer to P37,-39)
SOUND MENU
Used to adjust
volume or mute
sound.
(Refer to P23)
IMAGE SELECT MENU
Used to select
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P29)
FOR PC SOURCEPress MENU BUTTON...