Toshiba Projector Tlp 780U User Manual

11
Before use
Right side
Rear sideLeft side
Front side
Control panel
Air exhaust
Lens cover
LensInfrared remote sensor
Anti-theft lock
hole
Speaker
Air intake
Foot adjuster release button Foot adjusterZooming lever
Focusing ringAir intakeCarrying handle
Open to carry the projector.AC IN socket
• The air exhaust discharges high temperature air. Do not put something around the air exhaust, otherwise it may be deformed by the high temperature air.
Names of each part on the main unit
CAUTION
Openings in the...

12
Before use
KEYSTONE
AUTOSET
EXIT
ON / STANDBYVOL / ADJ
ENTER
MENU
INPUT
FAN
TEMP
LAMP
ON
KEYSTONE buttonTo correct the keystone distortion of
the picture.AUTO SET buttonTo adjust the image of the Computer
input automatically.
VOL/ADJ buttonTo set and/or adjust values on the menu.
To adjust volume when the menu is not displayed.
ENTER button Selection button EXIT button
MENU buttonON/STANDBY button
To turn the projector on or off (standby).
INPUT buttonTo select the input
source.To display the menu...

13
Before use
USB
COMPUTER IN 1
COMPUTER IN 2
S-VIDEO VIDEO
VIDEO IN
R - AUDIO - L
AUDIO
IN(
Y/PB/PR )
MONITOR
OUTCONTROL
COMPUTER IN 1 connectorTo enter RGB signal from a computer,
etc or  component video signal (Y/P
B/PR
Signal) from a video equipment.S-VIDEO connectorTo enter S-Video signal from a video
equipment, etc.VIDEO jackTo enter video signal from a video
equipment, etc.AUDIO(L/R) jacksTo enter audio signal from a video
equipment, etc.
AUDIO IN jack (Audio input)(φ3.5mm stereo mini-jack)
To...

14
Before use
MENUON/STANDBY
LASER INPUT
L-CLICK R-CLICK
ENTERKEYSTONE
AUTO
SET
EXIT
PIPFREEZEMUTE CALL
RESIZE
VOLUME/ADJUST
AVOIDEXPOSURE LASER 
MENUON/STANDBY
LASER INPUT
L-CLICK R-CLICK
ENTERKEYSTONEAUTO
SET
EXIT
PIPFREEZEMUTE CALLRESIZEVOLUME/ADJUSTLASER RADIATIONDO NOT STARE INTO  BEAM, CLASS 2 LASER PRODUCT LASER-STRAHLUNG
NICHT IN DEN STRAHL BLICKEN, LASER KLASSE 2 PRODUKTRAYONNEMENT LASER
NE PA S REGARDER DANS LE FAISCEAUAPPAREIL A LASER DE CLASSE 2
WAV E LENGTH (WELLENÄNGE,
LONGUEUR D ONDE) :...

15
Before use
321
Using batteries incorrectly can cause them to leak or
burst. Strictly observe the following.
• Install the batteries with their + and - ends
facingcorrectly.
• Do not charge, heat, disassemble, or short the
batteries or throw them into a fire.
• Do not leave exhausted batteries in the remote
control.
• Do not mix different types of batteries or new and
old batteries.
• When you will not be using the remote control for
a prolonged period, take the batteries out of the
remote control.
•...

16
Before use
RESIZEMENU
PIPFREEZEMUTE CALL
ON/STANDBY
LASER INPUT
ENTER
AUTO
EXIT VOLUME/ADJUST
SET
R-CLICK
L-CLICK
KEYSTONEAbout 15
°
About 15
°
About 15
°
About 5m
About 15
°
RESIZEMENU
PIPFREEZEMUTE CALL
ON/STANDBY
LASER INPUT
ENTER
AUTO
EXIT VOLUME/ADJUST
SET
R-CLICK
L-CLICK
KEYSTONEAbout 15
°
About 15
°
About 15
°
About 5m
About 15
°
Remote control operation
Point the remote control at the infrared remote sensor and press a button.•The remote control may not operate when there is sunlight or other...

17
Installation and
connection
Continued
Floor-mounted projector placement
There are two ways to place the floor-mounted projector. Perform the Projection mode setting on the menu screen for the projection
method.
For the ceiling-mounted projector placement, refer to the page        .
Floor-mounted front projection
Viewing a picture projected on the front of the screen from a floor
installation.
Floor-mounted rear projectionViewing a picture projected through the back of the screen from a
floor...

18
Installation and
connection
2 1
32
40
60
80
100
150
200
300-
1.42
2.16
2.90
3.63
5.48
7.33
11.021.42
1.80
2.74
3.67
4.60
6.93
9.26
-
a(m)
90°
a
90°
90°
Continued
Floor-mounted projector placement (continued)
Place the projector on a steady, level surface such as a table.To obtain proper screen projected, place the projector so that the projecting light hits the screen squarely.
Top view
Screen
Side view
Screen
Point the lens straight at the center of the screen as above.
Place the projector...

19
Installation and
connection
ON / STANDBY
FAN
TEMP
LAMP
ON
34
Connect the power cord.• Insert one end in the AC IN socket on the projector.
• Insert the other end in a wall outlet.
Power cord (Supplied)Light (Orange)
The three indicators, TEMP, LAMP, and ON, light in green
for several seconds and then the ON indicator lights in
orange and the projector turns to the standby mode.
Do not perform any operations while the three indicators
are lit green.
Take off the lens cover.
• When the projector is...

20
Installation and
connection
2 1
Projector placement angle adjustment
The tilt of the projector can be adjusted using the foot adjuster.
Lift the front of the projector until a tilt angle desired
is obtained and hold down the foot adjuster release
button.The foot adjuster will stretch.
Release the button to lock in position.Turn the foot adjuster to make fine adjustment of the
height.Turn clockwise to lift up.
Turn counterclockwise to lower.
Foot adjuster
release buttonFoot adjuster
Lift up
Lower
• To...