Toshiba Projector Tlp 561 User Manual

							21
Installation and
connections
CONTENTSProjector placement angle adjustment (Foot adjuster)
Foot adjuster
release buttonFoot adjuster The tilt of the projector can be adjusted using the foot adjuster.  Adjust this when the highest position by the lens shift dial 
20 is
insufficient.  Refer to “Projection on the screen” 
28, and adjust the foot adjuster after projecting a picture.
Lift the front of the projector until the desired tilt
angle is obtained and hold down the foot adjuster
release button.
The foot adjuster will extend.
Release the button to lock in position.
1
Turn the foot adjuster to make fine adjustment to
the height.
Turn clockwise to lift up.
Turn counterclockwise to lower.
2
Notes
•To put the foot adjuster back, hold down the foot adjuster release button and lower the front slowly.
•Be sure to hold the projector when putting the foot adjuster back so as not to let the front fall on your fingers.
•Do not tilt the projector at an angle exceeding the range adjustable by the foot adjusters, since the life duration of the lamp may be shortened.
Lift up
Lower 
						

							22
Installation and
connections
CONTENTS
Ceiling-mounted front projection
Viewing a picture projected on the front of the screen from a
ceiling installation.
Ceiling-mounted rear projection
Viewing a picture projected through the back of the screen from a
ceiling installation.
Perform the “Projection mode” setting on the menu screen for the projection method. 51
Note
The relation between the projection size and the distance to the screen is the same as that of the floor-mounted projection mode 18.
Translucent screen Viewer
Ceiling-mounted projector placement
CAUTION
When a ceiling mount is required, please consult with the dealer.
Viewer
USB AUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR ) 
						

							23
Installation and
connections
CONTENTS
Notes
•The projector cannot be connected to a computer without an analog RGB connector. For details, refer to the computer manual.
•You may not be able to connect some computers to the projector. For details, consult the dealer.
•When connecting to a Macintosh computer, some models may need a Mac adapter for connection.
•Some computers may have output modes which are not compatible with this projector. Check the compatibility of the connectors, signal levels, timing,
resolutions, etc.
Connecting a computer
You can project the picture from the computer.
Check that the power supplies for the projector and for the computer are off before connecting the cables.
COMPUTER IN connector
For use as both analog RGB and Y/P
B/PR input. At shipping from factory, it is 
set for use as analog RGB input.
AUDIO IN jack
For use as audio signal of all input sources.
RGB cable (supplied)
To AUDIO IN jackComputer
To COMPUTER IN connector
Be sure to connect in the proper 
direction.
To monitor port
Audio cable (supplied)ø3.5mm stereo mini-jack
To audio output port
USBAUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR )USBAUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR ) 
						

							24
Installation and
connections
CONTENTSConnecting video equipment
Note
The S-VIDEO IN connector and VIDEO IN jack can be used independently, but the audio input jack is used for all input sources.
You can project the picture from video equipment.
Check that the power supplies for the projector and for the video equipment are off before connecting the cables.
Pin plug (red)
To audio output (R)
(Yellow) To VIDEO IN jackTo S-VIDEO IN connector
Be sure to connect in the proper 
direction.To S-video output
Audio cable 
(supplied)Pin plug (white)
To audio output (L)
Pin plug (yellow)
To video output To AUDIO IN jackS-video cable
(not supplied)
Video cable
(supplied)Video equipment AUDIO IN jack
For use as audio signal of all input sources. S-VIDEO IN connector VIDEO IN jack
USBAUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR )
Continued 
						

							25
Installation and
connections
CONTENTSConnecting video equipment (continued)
You can project the picture from video equipment with component video output jack.
Check that the power supplies for the projector and for the video equipment are off before connecting the cables.
COMPUTER IN connector
For use as both analog RGB and Y/P
B/PR input. At shipping from factory, it is 
set for use as analog RGB input.
Change the setting on the menu screen when using as Y/P
B/PR input. 
AUDIO IN jack
For use as audio signal of all input sources.
To COMPUTER IN connector
Be sure to connect in the proper 
direction.
Pin plug (red)
To audio output (R) Monitor cable 
Mini D-sub 15P-BNC
(Not supplied)
Pin plug (white)
To audio output (L) (Blue) To P
B video output (Green) To Y video output
(Red) To P
R video output Adapter
BNC-pin
(Not supplied)
To AUDIO IN jack
Audio cable (supplied)Video equipment  
(DVD player, etc.)
USBAUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR )45 
						

							26
Installation and
connections
CONTENTSProjector operation control by a computer
CONTROL connector
Computer
To RS-232C port Control cable (supplied) To CONTROL connector
Be sure to connect in the proper 
direction.USB AUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR )
You can control the projector by a computer connected with the control cable supplied. 72
Check that the power supplies for the projector and for the computer are off before connecting the cables.
Note
Do not connect any cable other than the exclusive one supplied. 
						

							27
Installation and
connections
CONTENTSHow to use the output connector
You can output analog RGB signal to a computer monitor, etc.
Check that the power supplies for the projector and for the computer are off before connecting the cables.
Notes
• The analog RGB signals or Y/PB/PR signals of the COMPUTER IN connector are output from the COMPUTER OUT connector.
• Signals are output from the COMPUTER OUT connector even when in the standby mode.
• A general computer monitor may not display a normal picture with Y/P
B/PR signals.
USB AUDIO INCONTROLS-VIDEO IN VIDEO INCOMPUTER OUT (
Y/PB/PR )COMPUTER IN (
Y/PB/PR )
To COMPUTER OUT connector
Be sure to connect in the
proper direction.Computer monitor, etc. 
						

							28
Operations
CONTENTS
Preparation
1Install and connect the projector properly.
2Take off the lens cover.
Press ON/STANDBY.
The projector turns on and the ON, LAMP and FAN indicators
light in green.
(The LAMP indicator blinks while the lamp is warming up.)
The lamp lights and the start up display appears.
CAUTION – Do not look into the projection
lens while operating the projector.
Projection on the screen
ON / STANDBY
FANTEMPLAMPON
ON / STANDBY
FANTEMPLAMPON
(Green) (Green) (Green) (Green) (Green)(Green
 Flashing)
1
Continued
MENU
ON /INPUT
ENTER
CT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ
STANDBY
1
1
1
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
Indicators Remote control
Control panel
(Main unit side)
ON/STANDBY ON/STANDBY
Notes
•The startup screen disappears when you push the EXIT button or wait for a while. You can also
set the startup screen not to be displayed on the menu screen. 
51
•When a projector is used for the first time, the language selection menu is displayed after the
startup screen disappears. Set it up with procedures 2 and 3 on the next page. 
						

							29
Operations
CONTENTSProjection on the screen (continued)
Press ENTER to confirm.
Press EXIT to return to step 2 if you want to re-select a
language.3
Continued
MENU
ON /INPUT
ENTERCT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ
STANDBY
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
2
2,3
2 2,3
ENTER
ENTER
Remote control
Control panel
(Main unit side)Select a desired language with the
selection buttons (
  /  ), and
press ENTER.
A menu confirming the selection result is
displayed in the selected language.
2ENTER
ENTER
When a projector is used for the first time, the language selection menu, which is to select a
language for displaying menus or messages, is displayed. Select a desired language. (At
shipping from factory, it is set to English.)
Notes
•The language selection menu will not be displayed on the second and subsequent times you
turn on the power. However, if “Reset all”  
52 is executed, the language selection menu will
be displayed when the power is turned on next.
•The language can also be selected on the menu screen. 
50
•This Owner’s manual is described on the supposition that English was selected.
4
Turn on the connected equipment and put it in
playback mode.
Select “Cancel” or install driver contained in the supplied
CD-ROM, when the dialog box of the Add New Hardware
Wizard screen appears on the computer when connecting a
computer. (The supplied CD-ROM contains a driver information
file named TOSHIBA_TLP.inf. Click the Browse button of the
dialog box to find and designate this file.) 
						

							30
Operations
CONTENTS
Select the input source by pressing INPUT
repeatedly.
At shipping from factory, “Analog RGB” connected to
COMPUTER IN connector or “Video” connected to VIDEO IN
Jack can be selected. (You can select “Camera” when using the
model with a document imaging camera.)
The icon and the name of the selected input source appear on
the screen.
Projection on the screen (continued)
5-a
5-b
MENU
ON /INPUT
ENTER
CT-90106
KEYSTONE AUTO SET
EXIT /
P.MODE
PIP FREEZE
MUTE
CALLRESIZE
VOL / ADJ
STANDBY
5-a,5-b
5-b
5-a,5-b 5-b
KEYSTONE
AUTOSET
EXIT
ON / STANDBY
VOL / ADJ
ENTER
MENU
INPUT
FANTEMPLAMPON
INPUT
INPUT
INPUT
INPUT
ENTER
ENTER
Remote control
Control panel
(Main unit side)
Select the input source to project.
There are two kinds of methods as follows (5-a and 5-b.)
Note
The types of input sources selected when the INPUT button is pressed repeatedly can be
set from the menu screen. 
45
Continued
Press INPUT and hold for two seconds.
The input source selection menu appears.
Select the input source to project with the
selection buttons (
  /  ).
Regardless of the contents of input source settings on the
menu screen, all the input sources are displayed here for
selection.
Press ENTER.
A picture of the selected input source is projected.
When a sound signal source is also connected, sound is
emitted from the speaker.