Toshiba Projector Tdp Mt200 User Manual

							41
Others
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
■List of supported signals (Y/PB/PR signals)
Signal format fh(kHz) fv(Hz)
480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94
576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00
720p(750p)@60Hz 45.00 60.00
720p(750p)@50Hz 37.50 50.00
1080i(1125i)@60Hz 33.75 60.00
1080i(1125i)@50Hz 28.13 50.00
■List of supported signals (Video, S-Video signals)
Video mode fh(kHz) fv(Hz) fsc(MHz)
NTSC 15.73 60 3.58
PAL15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41
PAL-M 15.73 60 3.58
PAL-N 15.63 50 3.58
PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
■Pin assignment of COMPUTER terminal
11 156 1 5
10
Input Signal
•RGB input
RGB signals: 0.7V (p-p) 75 Ω
Horizontal sync signal:TTL level (Pos/neg polarity)
Vertical sync signal: TTL level (Pos/neg polarity) Mini D sub 15 Pin connector
Pin No. Pin  description
1Video signal (R)
2Video signal (G)
3Video signal (B)
4GND
5GND
6GND (R)
7GND (G)
8GND (B)
9N.C
10 GND
11 GND
12 N.C
13 Horizontal sync signal
14 Vertical sync signal
15 N.C 
						

							42
Specifications (Continued)
■Pin arrangement for the DVI-D terminal
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15Pin description
T.M.D.S. data 2–
T.M.D.S. data 2+
T.M.D.S. data 2/4 shield
T.M.D.S. data 4–
T.M.D.S. data 4+
DDC clock
DDC data
Analog vertical sync signal
T.M.D.S. data 1–
T.M.D.S. data 1+
T.M.D.S. data 1/3 shield
T.M.D.S. data 3–
T.M.D.S. data 3+
+5V power supply
GND(+5V, H Sync & V Sync) Pin description
Hot plug detection
T.M.D.S. data 0–
T.M.D.S. data 0+
T.M.D.S. data 0/5 shield
T.M.D.S. data 5–
T.M.D.S. data 5+
T.M.D.S. clock shield
T.M.D.S. clock+
T.M.D.S. clock–Pin No.
16
17
18
19
20
21
22
23
24
D V I - D
24
81
16179
DVI DIGITAL connector 
						

							43
Others
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
■CONTROL terminal
●Pin assignment
7
6
8
5
43
21
Signal Name
RXD
CTS
DSR
GND
RTS
N.C
TXD
GND Pin No.
1
2
3
4
5
6
7
8Description
Receiving data
Consent to send
Data set ready
Signal ground
Request to send
No connection
Sending data
Signal ground
Mini DIN 8 pin connector
●Interface format
1Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;
Stop Bit Length:  1 bit
2Communication format STX (02h)  Command (3Byte)  ETX (03h)
Only 1 command valid per communication.
3Data format For input commands, only ASCII-compliant all-uppercase
alphanumeric characters supported.
4Replies Acknowledge ACK (06h)  CR (0Dh)  Data ...  Normally ended
ACK (06h)  ESC (1Bh) ...  Abor ted
No acknowledge NAK (15h)
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
●Main Commands
Item Command
Computer input selectIN1
DVI input selectIN2
Video input selectIN3
S-video input selectIN4
YP
B/CBPR/CR input selectIN5
Item Command
Power onPON
Power offPSD
Icon display onMO0
Icon display offMO1
Auto setting (RGB input)PAT
Status display onDON
Status display offDOF
Note
•Contact your dealer for control cable and other commands.