Toshiba Projector Tdp Mt200 User Manual

							21
Preparations
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
(Orange)
■Connecting the power cord
1Insert the power cord connector into the
AC IN socket of the projector.
2Insert the power cord plug into a wall or
other power outlet.
■Turning the power on
1Turn on the main power switch
The ON indicator will change to
orange, indicating standby mode.
•After the main power switch is turned
on, the inner cooling fan starts
cooling.
2Press the ON/STANDBY
button.
The power turns on, and the following
3 green indicators light: ON, LAMP,
and FAN. After a moment, the start-up
screen appears.
Start-up screen
Control panelRemote
Control
Power cord connector
(Supplied)
 CAUTION
•Do not look into the lens while the lamp is on.  The strong light from the lamp may cause
damage to your eyes or sight.
•Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
•Do not place your hands, face, or other objects near the air exhaust. Doing so could cause
burns, deform/break the object.
■Removing the lens cover
Be sure to remove the lens cover when the power is
turned on. If it is left on, it could become deformed due
to heat. 
						

							22
Notes
•The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the start-up screen not to
appear via the Display setting menu 
p.30.
•The first time you use the projector after purchase, after the start-up screen disappears,
the Language menu is displayed 
p.23.
■ Turning the power off
1Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2Press the ON/STANDBY button again.
The screen turns off, but the internal cooling fan continues to operate for a short while.
Then, the projector goes into standby mode.
When cooling lamp During internal cooling After cooling complete
ABC(Orange) (Orange) (Green) (Green)(Off)
(Orange) Flashing(Green)(Off)
(Off)
ADuring cooling, the LAMP indicator flashes. In this state, the power cannot be
turned back on.
BAfter the LAMP indicator goes off, the cooling fan continues to operate for a
short while, in order to expel excess internal heat. If you are in a hurry, there is
no problem with unplugging the power cord or turning off the main power switch
in this state.
CIn standby mode
Note
•The projector consumes about 12W of power in standby. We recommend that you unplug
the power cord or turn off the main power switch if you will not be using the projector for
an extended period.
PRECAUTION
•If the power cord is unplugged before cooling is complete, give the lamp time (about 5
minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, and
its lifetime will be shortened.
Turning the power on and off (Continued) 
						

							23
Operations
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
1Turn on the power.
Turn on the power by following the instructions in “Turning the power on” p.21.
2 Select the language and the lamp power (When using the
first time).
When the projector is used for the first time after purchase, menu for language and
lamp power selection and configuration is displayed in English. (If the screen is out of
focus, adjust it according to the step 
6.)
qUse the  or  button to select the
desired language and press the 
 button.
Message for setup confirmation is displayed in a
selected language.
Then, the menu for lamp power selection and
configuration is displayed. It is automatically set as
Standard. To change the setting, follow the step w.
wUsing the  or  button, select the lamp
power and press the 
 button.
The lamp power, if selected, will be toggled without
pressing the 
 button. The display automatically
disappears in a few seconds.
Notes
•When the projector is turned on the next time, the Language and Lamp power
menus do not appear upon startup. However, if “Reset all” is executed from the
Default setting menu 
p.31, the Language and Lamp power menus will be
displayed the next time when the power is turned on.
•The language can also be set via the Display setting menu 
p.30 and Lamp power
via the Default setting menu 
p.31.
•This owner’s manual assumes that English has been selected.
3Activate the connected device.
Turn on and start the connected device such as a computer.
4Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment.
Basic operations
Notes
•When [Auto input search] is set to [On] in the default setting menu p.31, the image of
the equipment which is connected and turned on is projected.
•Moving pictures generated with the DVD software for computers may appear unnatural if
it is projected with this projector, but it is not a malfunction.
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean 
						

							24
5Projector placement angle adjustments
The placement angle and the height of the projected image can be adjusted by the foot
adjuster.
qLift up the front of the projector to
the desired angle, then press the
foot adjuster release button.
The foot adjuster extends. Release the
button to lock the position.
wTo adjust the horizontal angle, use
the tilt adjuster.
To stow the foot adjuster, hold up the projector
while pressing the foot adjuster release button,
then slowly lower the projector.
6Adjusting the screen size and focus
qUse the zooming lever to adjust the screen size.
wUse the focusing lever to adjust the focus.
Readjusting the projection size with the
zooming lever after focusing will cause the
projected image to be out of focus. In that case,
perform focusing again.
Notes
•Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.
•A lamp is consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out.  This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on conditions of use.)
•The DMD
TM is made using extremely advanced technology, but there may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel.  Please
note that these are not malfunctions.
•Although this projector supports a wide range of RGB signals 
p.39, any resolutions will
be expanded or shrunk, which will affect image quality slightly.
•With some models of computer having LCD displays or the like, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the owner’s manual of your computer.
•If a signal not supported by the projector is input, the “Unsupported signal” will appear.
•If no signal is being input from the connected device, the “No signal” will appear.
•If an unavailable operation button is pressed, the 
 icon will appear.
1
2




Basic operations (Continued) 
						

							25
Operations
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
■Using auto setting
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.
1Press the SET UP button.
The Set up menu appears.
2Press the SET UP button again.
The displayed menu item is automatically adjusted/set.
For computer input, the 
 icon will appear during
processing.
For manual adjustment and setting, see the following table 
p.26.
Notes
•The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector p.39, p.40,p.41.
•Keystone adjustment cannot be corrected automatically.
●Correcting the keystone distortion
When the foot adjuster p.24 is used to change the projector placement angle while
projecting the image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of correcting this keystone distortion.
●Manual adjustment
Press the SET UP button to display the Set up menu and select [Keystone]. Use
the 
  buttons for keystone adjustment. When the adjustment is finished, press
the RETURN button. The menu disappears.
Notes
•Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
•Keystone adjustment is available for the keystone distortion in a slant angle of ±15
degrees.
•Keystone adjustment will not change the shape of the menus, the start-up screen,
and the background (with no signal input).
Using handy features
Control panelRemote
Control
Before correctionAfter correction 
						

							26
Using handy features (Continued)
●Manual adjustments and settings
The menu items of the Set up menu vary depending on the input type, as shown in
the table below.
Use the 
     buttons to adjust the items in the table below, then press
the RETURN button when you are finished.
Select Item DescriptionComputer  DVIY/PB/PRVideo
S-video
KeystoneCorrect the keystone (trapezoid) distortion of the 
screen.
Screen shrinking             Screen shrinking
downward                        upward
Auto settingAutomatically adjusts items such as the sampling 
phase depending on the type of input signal.
Press the SET UP button.
PhaseAdjust with            to eliminate flicker.
FrequencyAdjust with             to eliminate periodic patterns 
and flickering when many vertical lines appear 
on the screen.
Image’sAdjust the horizontal position of the image.
H-positionMove left            Move right
Image’sAdjust the vertical position of the image.
V-positionMove down            Move up
Clamp 1Adjusts the clamp pulse position.
Lower            Higher
Clamp 2Adjusts the clamp pulse width.
Narrower            Wider
Ye s Ye s Ye s Ye s
Ye s N o NoNo
Ye s N o NoNo
Ye s N o NoNo
Ye s N o NoNo
Ye s N o NoNo
Ye s N o NoNo
Ye s N o NoNo 
						

							27
Operations
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
■Cutting off the picture temporarily (Mute)
When you want to project the images of another projector, overhead
projector, etc. temporarily, this projector’s images can be turned off.
Press the remote control’s MUTE button.
The picture is cut off. (The Mute function is released when pressing
the MUTE button again.)
Notes
•The  icon will appear while mute is in effect.
•Operating any other functions will also cancel the muting.
■Freezing the image (Freeze)
The image being projected can be frozen. This function is to be used to
pause a video during a presentation, etc.
Press the remote control’s FREEZE button.
The picture pauses. (The Freeze function is released when pressing
the FREEZE button again.)
Notes
•The  icon will appear while freeze is in effect.
•Other operation will also release the freeze.
•Even if an image is frozen on the projector, the pictures are running on the video or
other equipment.
•If you use this function on video software sold on the market, broadcast or
broadcast on cable except for the purpose of your private viewing and listening, it
may infringe the copyright protected by the copyright laws.
Remote
Control
Remote
Control 
						

							28
You can call up on-screen menus, and conduct a number of adjustments and settings using
the operation buttons p.16 on the control panel (main unit side) and remote control.
■How to use the menus
The menu shown below is for operation instructions purposes and might differ from the
actual display.
Using the menus
Note
•Menu adjustments and settings are saved when the power is turned off via the ON/
STANDBY button. If the power cable is disconnected before this, or the power goes out,
then the data will not be saved.
Display the Setting display menu
The menu disappears.
1. Press the MENU button
2. Select a Category
3. Adjustments & Settings
5. End
    
Press the MENU 
    button
Select a category by using           .
There are following four 
categories:Displays the current 
adjustments and settings of 
selected category.
Item shown with gray cannot 
be adjusted with the current 
input source.
p.29Image adjustment menu
p.30Display setting menu
Default setting menu
p.31
Status display menup.32
The figure shows displays given for operation instructions purposes.  As the display 
may differ depending on the item, use the following pages as a reference.
ItemAdjustment/Setting Value
These marks signify the 
items can be adjusted/set 
by using                .
These marks signify the items can 
be selected from the list by using
           .
After an item is selected, apply it 
by pressing      .
Press      to open the menu.
This mark signfy that 
there are options.
Press         to display a 
list of options.
4. Back
Return button 
						

							29
Operations
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
■The image adjustment menu
Use this menu to adjust image-related items.
Items that can be adjusted are marked with  “Yes”, and those that cannot are marked with “No”.
Item      DescriptionComputerY/PB/PRVideo
DV I
S-video
 ContrastAdjust the image contrast. Yes Yes Yes Yes
Lower
Higher
BrightnessAdjust the brightness of the image. Yes Yes Yes Yes
Darker
Brighter
ColorAdjust the color of the image. No Yes Yes No
Lighter
Deeper
Tint *1Adjust the tint of the image color. No No Yes No
Reddish
Greenish
SharpnessAdjust the sharpness of the image. No Yes Yes No
Softer
Sharper
NoiseSet the function to reduce screen noise. No Yes Yes No
reduction
On (Enable)
Off (Disable)
PicturePress . Toggle the picture mode with Yes Yes Yes Yes
mode
 / .
Dynamic/Standard/Theater
R-levelAdjust red of the image color. Yes Yes Yes Yes
Less red
More red
G-levelAdjust green of the image color. Yes Yes Yes Yes
Less green
More green
B-levelAdjust blue of the image color. Yes Yes Yes Yes
Less blue
More blue
NTSC mode*1Set the black level with  /  button. No No Yes No
US: NTSC (US) mode
Japan: NTSC (JAPAN) mode
*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to
[NTSC] and [NTSC4.43]. (NTSC mode is set to JAPAN when the language is set to Japanese. It is
set to US for other languages.) 
						

							30
Using the menu (Continued)
■The display setting menu
Use this menu to set screen display-related items.
Description
Screen size
Language
Background
Icon
Start-up screen
Item
Full           4:3           Zoom
Full : This mode is best for squeeze-signal video images.
4:3 : This mode is best for 4:3-signal video images on the 4:3-size screen.
Zoom : This mode is best for video images of letter-box or cinema signals.
Select one of the languages below to use for displaying the menu and messages 
[     : Enter setting mode]     [          :Selection]      [Apply:       ]
English/Français/Deutsch/Italiano/Español/Português/               /
Svenska/Türkçe/            /                      /                      /
Screen to display when there is no input signal
                 (Logo)                   (Blue)                   (Black)
Display icons as function guidesOn Off
Display start-up screen when power is turned on On Off
●Screen size
The screen size of this unit is 16:9, but the screen size can be changed according to
the input signal.
 Note
•Using these functions to change the picture size (i.e., changing the height/width
ratio) for any purpose other than your private viewing may be prohibited under the
Copyright Laws of the United States and other countries, and may subject you to
civil and criminal liability.
Projection screen
Input signal
4:3 signal
Squeeze signal
Letter box signal
Cinema signal
Full
Full (O)
Full
Full4:3 signal
4:3
4:3
4:3Zoom
Zoom
Zoom (O)
(O): Optimum screen size Zoom (O)
Notes
•The screen size cannot be changed when the 16:9 signal is input.
•You cannot select “Zoom” when the input is COMPUTER or DVI.