Toshiba Projector Tdp Mt200 User Manual

							Others
Maintenance
Operations
Preparations
Before Using
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
OWNER’S MANUAL
DLPâ„¢ PROJECTOR
TDP-MT200 
						

							2
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated dangerous voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
FCC NOTICE:This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.  These limits are designed to provide reasonable
protection against harmful interference in a residential installation.  This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES
ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
WARNING:Handling the cord on this product or cords associated with accessories sold with
this product, will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. 
Wash hands after handling.
WARNING:This [product] contains mercury. Disposal of mercury may be regulated due to
environmental considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
USA only
MODEL NAME: TDP-MT200
TRADE NAME: DLPâ„¢ PROJECTOR               MODEL NAME: TDP-MT200
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
USA only
SAFETY PRECAUTIONS
Before Using
USA only 
						

							Before Using
3
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: Toshiba America Consumer Products LLC
82 Totowa Road, Wayne, New Jersey, 07470
Phone: (973)628-8000
WARNING:Changes or modifications made to this equipment, not expressly approved by
Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.
Notice:This Class B digital apparatus complies with Canadian ICES-003.  Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
CANADA only
USA only 
						

							4
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNERS MANUAL AND THOSE
MARKED ON THE UNIT.  RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This set has been designed and manufactured to assure personal safety.  Improper use can
result in electric shock or fire hazard.  The safeguards incorporated in this unit will protect you
if you observe the following procedures for installation, use and servicing.  This unit is fully
transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO
DANGEROUS VOLTAGE.  REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.
1. Read Owners Manual
After unpacking this product, read
the owners manual carefully, and
follow all the operating and other
instructions.
2. Power Sources
This product should be operated
only from the type of power source
indicated on the marking label.
If you are not sure of the type of
power supply to your home,
consult your product dealer or
local power company.
For products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
3.Source of Light
Do not look into the lens while the
lamp is on.  The strong light from
the lamp may cause damage to
your eyes or sight.
4.Ventilation
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating, and these openings
must not be blocked or covered.
The openings should never be
blocked by placing the product on
a bed, sofa, rug or other similar
surface.  This product should not
be placed in a built-in installation
such as a bookcase or rack unless
proper ventilation is provided or
the manufacturers instructions
have been adhered to. 
						

							Before Using
5
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
5.Heat
The product should be situated
away from heat sources such as
radiators, heat registers, stoves, or
other products (including
amplifiers) that produce heat.
6.Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and the like.
7.Cleaning
Unplug this product from the wall
outlet before cleaning.  Do not use
liquid cleaners or aerosol cleaners.
Use a soft cloth for cleaning.
8.Power-Cord Protection
Power-supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
9.Overloading
Do not overload wall outlets;
extension cords, or integral
convenience receptacles as this
can result in a risk of fire or
electric shock. 
						

							6
IMPORTANT SAFETY INSTRUCTIONS  (Continued)
10.Lightning storms
For added protection for this
product during storm, or when it is
left unattended and unused for
long periods of time, unplug it from
the wall outlet.  This will prevent
damage to the product due to
lightning and power-line surges.
However, while it is thundering or
lightning, do not touch the
apparatus and any connected
cable and/or equipment.
This will prevent you from
receiving the electric shock by an
electric surge.
11. Object and Liquid Entry
Never push objects of any kind
into this product through openings
as they may touch dangerous
voltage points or short-out parts
that could result in a fire or electric
shock.  Never spill liquid of any
kind on the product.
12. Do not place the product
vertically
Do not use the product in the
upright position to project the
pictures at the ceiling, or any other
vertical positions.  It may fall down
and dangerous.
13. Stack Inhibited
Do not stack other equipment on
this product or do not place this
product on the other equipment.
Top and bottom plates of this
product develops heat and may
give some undesirable damage to
other unit.
14. Attachments
Do not use attachments not
recommended by the product
manufacturer as they may cause
hazards. 
						

							Before Using
7
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
15. Accessories
Do not place this product on an
unstable cart, stand, tripod,
bracket, or table.  The product may
fall, causing serious injury to a
child or adult, and serious damage
to the product.  A product and cart
combination should be moved with
care.  Quick stops, excessive
force, and uneven surfaces may
cause the product and cart
combination to overturn.
S3125A
16. Damage Requiring Service
Unplug this product from the wall
outlet and refer servicing to
qualified service personnel under
the following conditions:
a) When the power-supply cord or
plug is damaged.
b) If liquid has been spilled, or
objects have fallen into the
product.
c) If the product has been exposed to
rain or water.
d) If the product does not operate
normally by following the operating
instructions.  Adjust only those
controls that are covered by the
operating instructions as an
improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore
the product to its normal
operation.e) If the product has been dropped or
damaged in any way.
f) When the product exhibits a
distinct change in performance -
this indicates a need for service.
17. If glass components,
including lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass
components, including a lens and
a lamp.  If such parts should
break, please handle with care to
avoid injury and contact your
dealer for repair service.  The
broken pieces of glass may cause
to injury.  In the unlikely event of
the lamp rupturing, thoroughly
clean the area around the
projector and discard any edible
items placed in that area.
18. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards.  Refer all servicing to
qualified service personnel. 
						

							8
19. Replacement Parts
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
(Replacement of the lamp only
should be made by users.)
20. Safety Check
Upon completion of any service or
repairs to this product, ask the
service technician to perform
safety checks to determine that
the product is in proper operating
condition.
21. Do not leave thermal-paper
documents or easily
deformed items on top of
the unit or near the air
exhaust for long periods of
time.
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
IMPORTANT SAFETY INSTRUCTIONS  (Continued)
22. Do not use the product in
a closed installation state.
Do not place the product in a box
or in any other closed installation
state. Otherwise it may overheat.
This could result in a risk of fire. 
						

							Before Using
9
EnglishFrançaisEspañolDeutschItalianoPortuguêsSvenska
If your line voltage is 220 to 240V, use one of the following types of cable.
Plug
configurationPlug type
Australian
240V
10A
North American240V
15A Switzerland
240V
6A Line voltage
EURO
UK220 – 240V
220 – 240V200 – 240V
200 – 240V 200 – 240V
Plug
configurationPlug type Line voltage
Use a 5A fuse which is approved by ASTA 
or BSI to BSI362.
Always replace the fuse cover after 
changing the fuse.
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection, repack the set as it was originally packed at
the factory.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on
the crucial internal parts. To prevent the unit from possible damage, do not use the unit for
at least 2 hours when there is an extreme or sudden change in temperature
.
Place and Manner of Installation
•Do not place in hot locations, such as near heating equipment.  Doing so could cause
malfunction, and shorten the life of the projector.
•Avoid locations with oil or cigarette smoke.  Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.
•Do not use the product vertically in any upright position or slantwise in an angle of 20
degrees or more.
•Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
•Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts in the instrument. If you continue to use
it in that situation, the malfunction may result. Ensure to wait until the condensation
naturally disappears.
•In a high altitude location where air is thin, cooling efficiency is reduced so use it with the
ambient temperature being lowered.
POWER SUPPLY CORD SELECTION 
						

							
10
IMPORTANT PRECAUTIONS  (Continued)
Avoid Volatile  Liquid
Do not use volatile liquids, such as an insect spray, near the unit.  Do not leave rubber or
plastic products touching the unit for a long time.  They will leave marks on the finish.
If cleaning with a chemically saturated cloth, be sure to follow the products precautions.
In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.
Model No. Serial  No.
Retain this information for future reference.
EXEMPTION CLAUSES
•Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation,
operation, theft or mischief by third parties, other accidents, or use under abnormal
conditions including erroneous or improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
T oshiba Corporation.