Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

INSTALLATION INSTRUCTIONS 
SECTlON200-255-204 
FEBRUARY1992 
IBM XT PERSONAL COMPUTER 
OR ASCII TERMINAL 
(FUNCTIONS LIKE A DTE) 
DB25 PIN DESIGNATIONS 
PDIU-DI 
(FUNCTIONS LIKE A DCE) 
DB25 PIN DESIGNATIONS 
PDIU-DI 
PDIU-DI 
PIN# 1 2 
3 4 5 6 
7 6 20 22 
PIN# 1 
2 3 4 5 6 7 6 20 22 
NAME FG TD RD FITS CTS DSR SG DCD DTR RI 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of personal computer 
or ASCII te Rear view of PDIU-DI DB25. 
, 
1 CONNECTOR 1 
RS-232 CABLE 
IBM PC XT modem style (serial) 
DB25...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
TOSHIBA LAPTOP OR IBM AT-TYPE PDIU-DI 
PERSONAL COMPUTER (DTE) (FUNCTIONS LIKE A DCE) 
PIN DESIGNATIONS 
PIN DESIGNATIONS 
COM PORT 
PIN # PDIU-DI 
123456769 
PIN# 1 2 3 4 5 6 7 8 20 22 
NAME DCD RD TD DTR SG DSR RTS CTS RI 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of asynchronous (serial) 
communication interface connector (DB9) of Rear view of PIN-DI DB25, 
Toshiba laptop or IBM AT personal computer FE-232 female connector 
DE9...

INSTALLATION INSTRUCTIONS 
SECTlON200-255-204 
FEBRUARY1992 
NOTES: 
1. Only serial printers that conform to EIA 
M-232 signaling requirements can be 
connected to PDIU-DS units. 
2. In rare applications, printers can be con- 
nected to PDIU-Dls. Refer to the printer’s 
installation instructions. 
1) Consult the serial printer’s documentation, 
and determine if the printer operates as a DCE 
or DTE device: 
l As a DCE device: 
a) Disassemble the PDIU-DS, and con- 
figure it to operate like a DTE device...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
2) 
3) PDIU-DS disassembly/assembly instruc- 
tions, and Figure 4-54 provides jumper plug 
information). 
Connectthe PDIU-DS totheappropriate NDKU 
circuit in accordance with the wiring diagrams 
in Section 200-255-205. 
Connect the appropriate RS-232 cable be- 
tween the modem and the PDIU-DS. Figure 
4-60 shows an example of PDIU-DS to a 
Hayes modem RS-232 connection. 
IMPORTANT NOTE! 
All ten PDIU-DS EIA leads (signals) should 
be...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
HAYES-TYPE SMART MODEM 
(FUNCTIONS LIKE A DCE) PDIU-DS 
(CONFIGURED IN THE “CONNECT TO MODEM” 
MODE, Pl - P9 = B-C, SO IT FUNCTIONS LIKE A DTE) 
MODEM PDIU-DS 
PIN# 1 2 3 4 5 6 7 8 20 22 PIN# 1 2 3 4 5 6 7 8 20 22 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of modem DB25 connector 
Rear view of PDIU-DS DB25. connector 
DB25 FEMALE DB25 FEMALE 
CONNECTOR 
I 
DB25 n 
CONNE AALE 
ECTOR 
I ,825 
I I...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
DTE/h!ODEM 
JUMPER PLUGS 
PDIU-DS 
FIGURE 4-61-PDIU-DS DISASSEMBLY/ASSEMBLY DIAGRAM  

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
3 DKT/PDIU-DI 1 w 
LAPTOP PC 2 
FIGURE 4-62 FIGURE 4-63 
PC TO PC TEST CALL USING AT COMMANDS PC TO PRINTER TEST CALL USING MANUAL DIALING 
PERCEPTION,,,, 
TELEPHONE 
TELEPHONE 1 
LAPTOP PC 1 
LAPTOP - 
PC2 
FIGURE 4-64-INTERNAL PC TO EXTERNAL PC TEST CALL USING AT COMMANDS 
4-55  

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
MDF 
’ : 
I : NCOU 
NSTU ’ , ; ’ TRUNK - TELEPHONE 
I 
I :- - CIRCUIT 
! : 
LAPTOP PC 1 TELEPHONE 
PC2 
FIGURE 4-65-EXTERNAL PC TO INTERNAL PC TEST CALL USING AT COMMANDS 
6.182 PC to PC Test Call Using AT Commands 
1) Make sure that PC 1 and PC 2 are equipped 
with a communication software package, and 
that the communication parameters of each 
PC and the communication software package 
are set to the same values (data transmission 
rate,...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
l The CONNECT LED on the PDIU-DS will 
light. 
l The connection between the PC and the 
printer is complete. 
l If busy tone is sent to the DKT, the connec- 
tion is not complete. Try step 3 again. 
4) Operate the PC to print data as required. 
5) To terminate the call, press the DKT’s m 
button. 
6.184 Internal PC to External PC Test Call Using 
AT Commands 
1) Make sure PC 1 and PC 2 are equipped with 
a communication software package, and...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
3) From PC 2’s keyboard, type A T D X X X X and 
press m, where XXXX is the Data Exten- 
sion number. (AT commands must be capital 
letters.)ThispromptsthePDIU-DS to dial and 
connect to the PDIU-DI. 
l The CONNECT LED on the PDIU-DS 
will light, the DATA LED on the DKT 
will also light. 
l The screens on PC 1 and PC 2 dis- 
play “CONNECT XXXX,” where XXXX 
is the data transmission speed set by 
the communication software. 
l At this time PC 1...