Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

IMPORTANT NOTE! 
To use the PDIU-DI or PDIU-DS with AT 
commands, communications software or 
some program that performs “terminal 
emulation”must be loaded in the computer. 
The AT commands cannot be issued from 
the computer’s operating system prompt. 
6.100 Common DIU Connections 
6.101 The block diagram in Figure 4-51 illustrates 
common DIU connections. In this example, PDIU- 
Dls are connected to laptop personal computers 
(PC1 and PC2), and the PDIU-DS’s are connected 
to a serial printer and...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
1 LAPTOP, PC 1 
PERCEI 
PTiONeh.ex NOTES: 
1. W-232 cable and connector 
information is provided in 
Figures 4-53 to 4-54. 
DIIJ-DI I I r-l! 2. PDIU-DVPDIU-DS MDF 
station wiring to NDKU is in 
Section 200-255-205. 
UlIl 
3. Modem MDF station wiring to 
NSTU is in Section 200-255- 
DIAL-UP 
COMPUTER 
I fiff!E&MODEM I I I L 
I aMoDEM I 111 
- m-m 
PDIU-DS u 
IL 
TFI FDUANF 1 
I 
TELEPHONE 
PC3 . 
FIGURE 4-51-PERCEPTION DATA INSTALLATION EXAMPLE...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
CONNECTION EXAMPLE 1 
DIGITAL 
TELEPHONE 
TOSHIBA LAPTOP OR IBM AT TYPE 
PERSONAL COMPUTER (PC) 
PDIU-DI BASE 
I 
L TYPE 1 MODULAR ADAPTER’ 
/ L EikfY;;;;;ssED)’ 
IMPORTANT! 
Will not function with applications that require the Ring Indicator signal to PC. 
CONNECTION EXAMPLE 2 
DIGITAL TELEPHONE IBM PC OR Xl TYPE 
PERSONAL COMPUTER (PC) 
PDIU-DI BASE 
TYPE 3 MODULAR ADAPTER’ 
TYPE A MODULAR CORD (STRAIGHT)’ 
(50 ft max, 24AWG) 
TYPE 2 MODULAR...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
TYPE 1 RJ45 TO DB9 (FEMALE) ADAPTER 
8 7 6 5 4 2 1 N/C RJ45 
DSR RTS RD DCD TD GND CTS RI LEAD 
NAME 
6 7 2 1 3 5 8 9 DB9 
TYPE 2 
RJ45 TO 
DB25 (MALE) ADAPTER 
8 7 6 5 4 3 2 1 N/C RJ45 
CTS SG 
DTR TD DCD RD RTS DSR RI LEAD 
NAME 
5 
7 20 2 8 3 4 6 22 DB25 
2345678 
l ooooeooooooo 
l ooooooooooo 
TYPE 3 
RJ45 TO DB25 (FEMA ,I -E) ADAPTER 
CTS SG DTR TD DCD RD RTS DSR RI LEAD 
NAME 1 
5 7 20 2 8 3 4 6 22 DB25 
FRONT 
RJ45 STRAIGHT THROUGH 1 1...

lNSTALLATlONlNSTRUCTlONS 
SECTION 200-255-294 
FEBRUARY1992 
PDIU-DS (FRONT VIEW) PDIU-DS (REAR VIEW) 
MODULAR JACK 
FOR CONNECTING 
E FIGURE 4-55 FOR 
POWER LED SWITCH (1 - 4) OPTIONS 
INFORMATION 
Pl - P9 LOCATED ON PCB INSIDE 
OF PDIU-DS UNIT (SEE NOTES) RS-23i, DB25 
(FEMALE) CONNECTOR 
SIGNAL DIRECTION AND FUNCTION OF Pl - P9 
POIU-DS CONNECTED TO CITE 1 PDIU-DS CONNECTED TO DCE 
I FG 
-1 FRAME GROUND 
I 1 I I~- -I-- I I 
SG SIGNAL GROUND 
TD TRANSMIT DATA 7 
2 DTE e DIU Pl 
MODEM c DIU Pl 
I RD 
I...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
PDIU-DI (BOmOM VIEW) DIP SWITCH 
ACCESS FROM BOTTOM 
- OUTSIDE OF PDIU-DI 
DIP SWITCH SWI BACK VIEW 
(ACCESS FROM BACK 
PDIU-DI DIGITAL TELEPHONE BASE 1 OUTSIDE OF PDIU-DS) 
PDIU-DS (REAR VIEW) 
I 
DB25 CONNECTOR (FEMALE) MODULAR 
FOR DTE OR DCE RS-232 CONNECTOR 
CABLE CONNECTION FOR NDKU LINE 
CONNECTION 
PDIU-DI AND -DS SW1 DIP SWITCH (1 .. 4) FUNCTIONS 
SWITCH 
SW1 
(1) 
SW1 
(2) 
SW1 
(3) 
SW1 
(4) FUNCTION 
Forced hang up when DIU does...

INSTALLATIONIN~TRUCTlONS 
SECTION 200-255-204 
FEBRUARY1992 
l Clear to Send (CTS, Pin 5): The DCE 
device sends the CTS signal (EIA circuit 
CB) which indicates that it is prepared to 
transmit data to the DTE device. The 
DCE device sends this signal, only when 
it receives the RTS signal from the DTE 
device. Sometimes, the DTE/DCE de- 
vice may use RTS/CTS for Ready/Busy- 
type flow control; in these cases, dip 
switch SW1 -4 should be set to OFF (see 
Figure 4-55 for the DIP switch informa- 
tion)....

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
6.120 DIP Switch Options 
6.121 Each of the PDIU-DI and the PDIU-DS data 
units has a four-control DIP switch which can be 
configured for signaling options. The switch is 
located on the bottom of the PDIU-DI, and on the 
back panel of the PDIU-DS (see Figure 4-55). 
l SW1 -1: Normally, this switch is set to OFF. When 
set to ON, it automatically disconnects devices 
from the PDlUs if no data is exchanged between 
the devices and PDIU for an...

NOTE: 
A digital telephone with a PDIU-DI attached 
cannot be wall-mounted. 
6.140 PDIU-DI to Personal Computer (PC) 
Installation 
6.141 The PDIU-DI always functions as a DCE 
device; it transmits data on the Receive Data lead 
(RD) and receives data on the Transmit Data lead 
(TD). Most personal computers function as DTE 
devices; PCs transmit data on the TD lead and 
receive data on the RD lead. Follow the steps below 
to install the PDIU-DI to a DTE or DCE PC: 
NOTES: 
1. 
2. 
1) 
2) 
Use the steps...

INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
TOSHIBA PS321SL PRINTER 
PDIU-US 
(FUNCTIONS LIKE A DTE) 
(CONFIGURED IN THE “CONNECT TO DTE” MODE: 
Pl - P9 = A-B SO PDIU FUNCTIONS LIKE A DCE) 
DB25 PIN DESIGNATIONS 
DB25 PIN DESIGNATIONS 
PRIMER 
PIN# 1 2 3 4 5 6 7 8 
20 22 
piK#Ds 12345678 20 22 
NAME FG TD RD FITS N/C DSR SG DCD DTR RI 
NAME FG TD RD RTS CTS DSR SG DCD DTR RI 
Rear view of printer 
(50 ft max, 24 AWG; 
customer supplied). 
NOTES: 
1. The printer receives data on pin 3...