Toshiba L50c Manual

You may not have all the software listed above depending on the modelyou purchased.
Special features
The following features are either unique to TOSHIBA computers or are
advanced features which make the computer more convenient to use.
Access each function using the following procedures. *1  To access the Power Options, click  Desktop -> Desktop Assist (in 
taskbar) -> Control Panel -> System and Security -> Power Options .
Display automatic
power off  *1This feature automatically cuts off power to the...

Low battery
automatic Hibernation
Mode  *1When battery power is exhausted to the point
that computer operation cannot be continued, the
system automatically enters Hibernation Mode
and shuts itself down. This can be specified in the Power Options.Sleep ModeIf you have to interrupt your work, you can use
this feature to allow you to turn off power to the
computer without exiting from your software.
Data is maintained in the computer's main memory so that when you next turn on the
power, you can...

TOSHIBA Password UtilityThe TOSHIBA Password Utility provides two levels of password security:User and Supervisor.Passwords set by the TOSHIBA Password Utility function are different from
the Windows password.
User Password
To start the utility, click the following items:
Desktop -> Desktop Assist (in taskbar) -> Tools & Utilities -> Password Utility -> User Password
User authentication may be required to validate user rights when using
TOSHIBA Password Utility to delete or change passwords, etc.
Set...

You can use BIOS Setup to set, change or delete the HDD Password or
HDD Master Password.
To start BIOS Setup.
1. In the  Settings  charm, click  Power and then select  Restart.
2. Hold down the F2 key and then release this key one second after
the computer is power on - the BIOS setup utility will load.
To end the BIOS Setup, press  F10, and then press  ENTER to accept
the changes. The computer will restart.
If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will...

1. Turn on the power as described in the Getting Started section. The
following message will appear in the screen:
Enter Password [ ]At this point, the function keys do not work. They will function after you enter the password.
2. Enter the Password.
3. Press  ENTER.
If you enter the password incorrectly three times in a row, or if you don’t
enter the password within 1 minute, the computer shuts off. In this case,
some features that can power on the computer automatically (Wake-up on
LAN, Task Scheduler,...

Keyboard—Allows you to access the wake-on keyboard function, or toconfigure the function keys
USB—Allows you to set conditions for USB
SATA—Allows you to set conditions for SATA
LAN—Allows you to set conditions for LAN
The settings or options explained here may vary depending on the model
you purchased.
After you changed the settings, a dialog box may appear to prompt you that
the changes will take effect after the computer is restarted. Make sure to restart your computer immediately to apply these...

If Sleep and Charge function is enabled, the computer’s battery will
discharge during hibernation or when the computer is turned off. It is
recommended that you connect the AC adaptor to the computer while
using Sleep and Charge function.
External devices connected to the USB bus power (DC5V) function
that interfaces with the power ON/OFF of the computer may always be
in an operational state.
When there is a current overflow of the external devices connected to
the compatible ports, USB bus power (DC5V)...

DisabledEnables Sleep and Charge function only when
the AC adaptor is connected.Disable features when
the battery level
reachesSpecifies the lower limit of remaining battery life
by moving the slider bar. If the remaining battery
life falls below the setting, the Sleep and Charge function will be stopped.
This setting is only available when the  Function 
under Battery Mode  is enabled.
System ON CDP Charge
This function enable/disable CDP (Charging Downstream Port) to use rapid
USB charge while the...

"Power OFF" includes Sleep Mode, Hibernation Mode or shutdown state.
To set Sleep and Music feature, click  Desktop -> Desktop Assist (in 
taskbar) -> Tools & Utilities -> System Settings -> Sleep and Music .
Move the slider to enable or disable the Sleep and Music function.When Sleep and Music function is enabled, it is not possible to mute
sound from the speaker even by connecting headphones to the
Headphone jack. There is also no sound from the headphone.
When Sleep and Music function is...

Notes on useThis software is a multimedia player which can be used to play back video,
music and photo. However, some files may not be able to play back normally.
It is recommended that the AC adaptor be connected while TOSHIBA
Media Player is running. Power saving features may interfere with
smooth playback. When TOSHIBA Media Player is used with a battery
power, set the Power Options to "Balance".
The screen saver is disabled while TOSHIBA Media Player is playing
a video file or slideshows of...