Toshiba E Studio 167 User Manual
Here you can view all the pages of manual Toshiba E Studio 167 User Manual. The Toshiba manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 31
![Page 31
To Print Lists 29
NIC status page
You can print out the setting status of the NIC (Network Interface Card) of the Network Printer Kit
(optional).
1Press the [USER FUNCTIONS]
button.
The “user functions mode” main screen
appears.
2Press or to select LISTS,
and then press the [ENTER]
button.
3Press or to select NIC
STATUS PAGE, and then press
the [ENTER] button.
“Printing accepted” appears and the NIC
status page is printed out.
USER FUNCTIONS1216
01.DEFAULT SETTINGS
02.LISTS
03.INITIAL...](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-30.png "Page 31
To Print Lists 29
NIC status page
You can print out the setting status of the NIC (Network Interface Card) of the Network Printer Kit
(optional).
1Press the [USER FUNCTIONS]
button.
The “user functions mode” main screen
appears.
2Press or to select LISTS,
and then press the [ENTER]
button.
3Press or to select NIC
STATUS PAGE, and then press
the [ENTER] button.
“Printing accepted” appears and the NIC
status page is printed out.
USER FUNCTIONS1216
01.DEFAULT SETTINGS
02.LISTS
03.INITIAL...")
To Print Lists 29 NIC status page You can print out the setting status of the NIC (Network Interface Card) of the Network Printer Kit (optional). 1Press the [USER FUNCTIONS] button. The “user functions mode” main screen appears. 2Press or to select LISTS, and then press the [ENTER] button. 3Press or to select NIC STATUS PAGE, and then press the [ENTER] button. “Printing accepted” appears and the NIC status page is printed out. USER FUNCTIONS1216 01.DEFAULT SETTINGS 02.LISTS 03.INITIAL...
Page 32
Downloaded From ManualsPrinter.com Manuals
Page 33
5.CONFIGURING NETWORKS (EQUIPMENT) This chapter describes how to configure networks using the control panel of this equipment. Network Configuration from Equipment...............................................................32 Ethernet Configuration ...........................................................................................33 TCP/IP Configuration ..............................................................................................35 IPX/SPX...
Page 34
![Page 34
5 CONFIGURING NETWORKS (EQUIPMENT)
32 Network Configuration from Equipment
Network Configuration from Equipment
You can perform the following network configurations using the [USER FUNCTIONS] button:
P.33 “Ethernet Configuration”
P.35 “TCP/IP Configuration”
P.40 “IPX/SPX Configuration”
P.42 “AppleTalk Configuration”
P.44 “HTTP Configuration”
To use TopAccess:
Before using a web-based utility TopAccess, TCP/IP protocol and HTTP network server service
must be configured in this equipment....](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-33.png "Page 34
5 CONFIGURING NETWORKS (EQUIPMENT)
32 Network Configuration from Equipment
Network Configuration from Equipment
You can perform the following network configurations using the [USER FUNCTIONS] button:
P.33 “Ethernet Configuration”
P.35 “TCP/IP Configuration”
P.40 “IPX/SPX Configuration”
P.42 “AppleTalk Configuration”
P.44 “HTTP Configuration”
To use TopAccess:
Before using a web-based utility TopAccess, TCP/IP protocol and HTTP network server service
must be configured in this equipment....")
5 CONFIGURING NETWORKS (EQUIPMENT) 32 Network Configuration from Equipment Network Configuration from Equipment You can perform the following network configurations using the [USER FUNCTIONS] button: P.33 “Ethernet Configuration” P.35 “TCP/IP Configuration” P.40 “IPX/SPX Configuration” P.42 “AppleTalk Configuration” P.44 “HTTP Configuration” To use TopAccess: Before using a web-based utility TopAccess, TCP/IP protocol and HTTP network server service must be configured in this equipment....
Page 35
![Page 35
Ethernet Configuration 33
Ethernet Configuration
You can specify the link speed and communication mode of Ethernet.
1Press the [USER FUNCTIONS]
button when the ready screen
is displayed.
The “user functions mode” main screen
appears.
2Press or to select INI-
TIAL SETUP, and then press
the [ENTER] button.
3Press or to select NET-
WORK, and then press the
[ENTER] button.
4Press or to select ETH-
ERNET, and then press the
[ENTER] button.
5Press or to select LINK
SPEED/DUPLEX MODE,...](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-34.png "Page 35
Ethernet Configuration 33
Ethernet Configuration
You can specify the link speed and communication mode of Ethernet.
1Press the [USER FUNCTIONS]
button when the ready screen
is displayed.
The “user functions mode” main screen
appears.
2Press or to select INI-
TIAL SETUP, and then press
the [ENTER] button.
3Press or to select NET-
WORK, and then press the
[ENTER] button.
4Press or to select ETH-
ERNET, and then press the
[ENTER] button.
5Press or to select LINK
SPEED/DUPLEX MODE,...")
Ethernet Configuration 33 Ethernet Configuration You can specify the link speed and communication mode of Ethernet. 1Press the [USER FUNCTIONS] button when the ready screen is displayed. The “user functions mode” main screen appears. 2Press or to select INI- TIAL SETUP, and then press the [ENTER] button. 3Press or to select NET- WORK, and then press the [ENTER] button. 4Press or to select ETH- ERNET, and then press the [ENTER] button. 5Press or to select LINK SPEED/DUPLEX MODE,...
Page 36
![Page 36
5 CONFIGURING NETWORKS (EQUIPMENT)
34 Ethernet Configuration
7Press the [ENTER] button.
The screen returns to the shown in step 5.
10Press the [CANCEL] button once or press the [FUNCTION CLEAR]
button to return the screen to the “user function mode” main
screen.
If the network connection is still unstable even after following the procedure above, turn
the power of this equipment OFF and then back ON.AUTO: Detects the Ethernet link speed automatically.
10BASE/HALF: Uses 10BASE-T half-duplex...](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-35.png "Page 36
5 CONFIGURING NETWORKS (EQUIPMENT)
34 Ethernet Configuration
7Press the [ENTER] button.
The screen returns to the shown in step 5.
10Press the [CANCEL] button once or press the [FUNCTION CLEAR]
button to return the screen to the “user function mode” main
screen.
If the network connection is still unstable even after following the procedure above, turn
the power of this equipment OFF and then back ON.AUTO: Detects the Ethernet link speed automatically.
10BASE/HALF: Uses 10BASE-T half-duplex...")
5 CONFIGURING NETWORKS (EQUIPMENT) 34 Ethernet Configuration 7Press the [ENTER] button. The screen returns to the shown in step 5. 10Press the [CANCEL] button once or press the [FUNCTION CLEAR] button to return the screen to the “user function mode” main screen. If the network connection is still unstable even after following the procedure above, turn the power of this equipment OFF and then back ON.AUTO: Detects the Ethernet link speed automatically. 10BASE/HALF: Uses 10BASE-T half-duplex...
Page 37
TCP/IP Configuration 35 TCP/IP Configuration You can configure TCP/IP protocol. This TCP/IP configuration includes address assignment method selection, IP address, subnet mask, and default gateway assignment (manual assign- ment). yThe configuration of TCP/IP protocol differs depending on your network environments. yBefore using a web-based utility TopAccess, TCP/IP protocol and HTTP network server ser- vice must be configured in this equipment. For HTTP configuration, see the following page: P.44...
Page 38
![Page 38
5 CONFIGURING NETWORKS (EQUIPMENT)
36 TCP/IP Configuration
7Press the [ENTER] button.
The screen returns to the shown in step 5.
3Press or to select NET-
WORK, and then press the
[ENTER] button.
4Press or to select TCP/
IP, and then press the [ENTER]
button.
5Press or to select
ADDRESS MODE, and then
press the [ENTER] button.
6Press or to select the
desired method of automatic
IP address assignment.
DYNAMIC: Obtains an IP address automatically using the Auto IP function and...](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-37.png "Page 38
5 CONFIGURING NETWORKS (EQUIPMENT)
36 TCP/IP Configuration
7Press the [ENTER] button.
The screen returns to the shown in step 5.
3Press or to select NET-
WORK, and then press the
[ENTER] button.
4Press or to select TCP/
IP, and then press the [ENTER]
button.
5Press or to select
ADDRESS MODE, and then
press the [ENTER] button.
6Press or to select the
desired method of automatic
IP address assignment.
DYNAMIC: Obtains an IP address automatically using the Auto IP function and...")
5 CONFIGURING NETWORKS (EQUIPMENT) 36 TCP/IP Configuration 7Press the [ENTER] button. The screen returns to the shown in step 5. 3Press or to select NET- WORK, and then press the [ENTER] button. 4Press or to select TCP/ IP, and then press the [ENTER] button. 5Press or to select ADDRESS MODE, and then press the [ENTER] button. 6Press or to select the desired method of automatic IP address assignment. DYNAMIC: Obtains an IP address automatically using the Auto IP function and...
Page 39
![Page 39
TCP/IP Configuration 37
10Press the [CANCEL] button once or press the [FUNCTION CLEAR]
button to return the screen to the “user function mode” main
screen.
You can check the configuration status and the obtained value if you print out the NIC
status page.
P.29 “NIC status page”
Manual IP address assignment
1Press the [USER FUNCTIONS]
button when the ready screen
is displayed.
The “user functions mode” main screen
appears.
2Press or to select INI-
TIAL SETUP, and then press
the [ENTER]...](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-38.png "Page 39
TCP/IP Configuration 37
10Press the [CANCEL] button once or press the [FUNCTION CLEAR]
button to return the screen to the “user function mode” main
screen.
You can check the configuration status and the obtained value if you print out the NIC
status page.
P.29 “NIC status page”
Manual IP address assignment
1Press the [USER FUNCTIONS]
button when the ready screen
is displayed.
The “user functions mode” main screen
appears.
2Press or to select INI-
TIAL SETUP, and then press
the [ENTER]...")
TCP/IP Configuration 37 10Press the [CANCEL] button once or press the [FUNCTION CLEAR] button to return the screen to the “user function mode” main screen. You can check the configuration status and the obtained value if you print out the NIC status page. P.29 “NIC status page” Manual IP address assignment 1Press the [USER FUNCTIONS] button when the ready screen is displayed. The “user functions mode” main screen appears. 2Press or to select INI- TIAL SETUP, and then press the [ENTER]...
Page 40
![Page 40
5 CONFIGURING NETWORKS (EQUIPMENT)
38 TCP/IP Configuration
6Press or to select
STATIC IP, and then press the
[ENTER] button.
The screen returns to the one shown in
step 5.
7Press or to select IP
ADDRESS, and then press the
[ENTER] button.
8Enter the IP address, and then
press the [ENTER] button.
The screen returns to the one shown in
step 7.
9Press or to select SUB-
NET MASK, and then press the
[ENTER] button.
10Key in the subnet mask value
as required, and then press the
[ENTER]...](http://img.usermanuals.tech/thumb/76/37929/w300_Toshiba_E-Studio_167-39.png "Page 40
5 CONFIGURING NETWORKS (EQUIPMENT)
38 TCP/IP Configuration
6Press or to select
STATIC IP, and then press the
[ENTER] button.
The screen returns to the one shown in
step 5.
7Press or to select IP
ADDRESS, and then press the
[ENTER] button.
8Enter the IP address, and then
press the [ENTER] button.
The screen returns to the one shown in
step 7.
9Press or to select SUB-
NET MASK, and then press the
[ENTER] button.
10Key in the subnet mask value
as required, and then press the
[ENTER]...")
5 CONFIGURING NETWORKS (EQUIPMENT) 38 TCP/IP Configuration 6Press or to select STATIC IP, and then press the [ENTER] button. The screen returns to the one shown in step 5. 7Press or to select IP ADDRESS, and then press the [ENTER] button. 8Enter the IP address, and then press the [ENTER] button. The screen returns to the one shown in step 7. 9Press or to select SUB- NET MASK, and then press the [ENTER] button. 10Key in the subnet mask value as required, and then press the [ENTER]...