Toshiba B852 User Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.12 Position and Print Tone Fine Adjustment
 
E2-58 
2.12  Position and Print  Tone Fine 
Adjustment (Cont.) 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a fine adjustment value, press the  [PAUSE] key. 
 
 
Reverse Feed Amount Fine Adjustment 
NOTES: 
Choose a desired value by using the
[RESTART] or [FEED] key.  
Pressing the [FEED] key one time
causes a –0.1mm change, up to  
–9.9 mm. 
Pressing the [RESTART]  key one
time causes...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.12 Position and Print Tone Fine Adjustment
 
E2-59 
2.12  Position and Print  Tone Fine 
Adjustment (Cont.) 
 
 
 
 
 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a fine adjustment value, press the 
[PAUSE] key. 
 
 
 
 
 
 
 
X Coordinate Fine Adjustment
NOTES: 
Choose a desired value by using the
[RESTART] or [FEED] key.  
Pressing the [FEED] key one time
causes a –0.1mm change, up to  
–99.9 mm. 
Pressing the [RESTART]  key...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.12 Position and Print Tone Fine Adjustment
 
E2-60 
2.12  Position and Print  Tone Fine 
Adjustment (Cont.) 
 
 
 
 
 
 
 
 
   
 
 
  Thermal Transfer Print  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a fine adjustment valu e or to skip this menu, press the 
[PAUSE]  key. 
 
 
 
  Thermal Direct Print  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a fine adjustment valu e or to skip this menu, press the 
[PAUSE]  key. 
 
 
 
 
 
Print...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.12 Position and Print Tone Fine Adjustment
 
E2-61 
2.12  Position and Print  Tone Fine 
Adjustment (Cont.) 
 
 
 
 
 
   
 
When the ribbon is slack or wrinkled a nd printing is affected, fine adjust 
the ribbon motor torque by using the following procedure. 
 
 
Take-up Motor (RBN ADJ ) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a fine adjustment valu e or to skip this menu, press the 
[PAUSE]  key. 
 
 
 
 
Feed Motor (RBN ADJ )...

2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting
 
E2-62 
2.13 Threshold Setting 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  To maintain a constant print position 
the printer uses the media sensor to 
detect a print start position according to the difference of voltage between 
a print area and a gap or black mark.  When the media is pre-printed, the 
darker (or more dense) inks can inte rfere with this process causing paper 
jam errors. 
To get around this problem, first, try an...

2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting
 
E2-63 
2.13 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
If a paper jam error still occurs even 
after an automatic threshold setting 
has been performed, manually set the threshold voltage.   
 
To make a threshold value manually set in this section effective, select 
the Transmissive Sensor (when us ing manual threshold value) or 
Reflective Sensor (when using manual  threshold value) within software...

2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting
 
E2-64 
2.13 Threshold Setting  (Cont.) 
 
 
 
  „
 When using the Black Mark Sensor  
(1) While “SENSOR ADJ.” is displayed, press the  [PAUSE] key 
until the message appears.  
  The displayed value is a real-time voltage being detected by the Black  Mark Sensor. 
 
 
 
(2) Measure a voltage at a blank part of media and a black mark, 
respectively.  At this time, write down the midpoint between both 
voltages. (This value is used later...

2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting
 
E2-65 
2.13 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
„ Storing a “No Media Level” Voltage  
The following is how to set a “No medi a level” voltage that is used to 
detect a paper end.   
If a “NO PAPER” is displayed even if the media has not run out yet, this 
voltage needs to be set again.  
 
(1) Remove any media from the Black Mark Sensor/Feed Gap Sensor.  
 
(2) A real-time voltages being...

2.PRINTER SETUP ENGLISH VERSION EO1-33055 2.13 Threshold Setting
 
E2-66 
2.13 Threshold Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
  (3) Press  the 
[PAUSE] key until the target sensor type is displayed.  
 
 
 
 
 
 
 
(4) Set a threshold voltage (calculate d in Sensor Adjustment Menu) by 
using the  [FEED] or [RESTART]  key, as shown below.  
 
  Threshold voltage =  Midpoint between voltage at a print area and 
voltage at a gap/black mark 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(5) After choosing a...

3. ON LINE MODE ENGLISH VERSION EO1-33055 
3.1 Operation Panel 
 
E3- 1 
3.  ON LINE MODE 
 
 
 
 
 
3.1 Operation Panel 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This chapter describes usage and purpose of the keys on the Operation 
Panel in On Line Mode.  
When the printer is in On Line Mode and connected to a host computer, 
normal operation of printing images on labels or tags can be 
accomplished.  
 
 
 
• The figure below illustrates the Operation Panel and key functions....