Toshiba B852 User Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-18 
2.9.1 Parameter Setting  (Cont.) 
 
 
 
  (5)  Stop Bit Length Selection 
This parameter is to choose a stop bit length of the RS-232C interface.   
Be sure to match a setting with a host computer.  
When “PARAMETER SET” appears, press the 
[PAUSE] key until 
the following display appears. 
 
 
 
Use the  [FEED]  or [RESTART]  key to select a desired option. 
 
 
 
 
 
 
After selecting a stop bit length, press the...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-19 
2.9.1 Parameter Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  (8)  LCD Language Selection 
This parameter is to choose a langua
ge in which the LCD message is 
displayed.   
When “PARAMETER SET” appears, press the  [PAUSE] key until 
the following display appears. 
 
 
 
Use the  [FEED]  or [RESTART]  key to select a desired option. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a language, press the  [PAUSE]...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-20 
2.9.1 Parameter Setting  (Cont.) 
 
 
  When ON is selected, pressing the 
[PAUSE] key will result that the LCD 
Message Display shows the stop position fine adjustment value setting 
screen. 
 
 
 
 
 
 
 
 
 
[FEED]  key: Pressing the  [FEED] key one time causes a –0.5mm change, 
up to –5.0 mm. 
[RESTART]  key:  Pressing  the  [RESTART] key one time causes a +0.5mm 
change, up to +5.0 mm. 
 
After selecting an...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-21 
2.9.1 Parameter Setting  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  After setting the control code for Control Code 1, press the
 [PAUSE]  
key to show the CONTROL CODE2 screen.  In a same manner, press the 
[PAUSE]  key after setting the control code  for Control Code 2 to display 
the CONTROL CODE3 screen. 
 
 
 
 
 
 
 
 
 
Press the  [PAUSE]  key after setting the control code...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-22 
2.9.1 Parameter Setting  (Cont.) 
 
 
 
  (12)  KANJI Code Selection 
This parameter is to choose a KANJI code.   
When “PARAMETER SET” appears, press the 
[PAUSE] key until 
the following display appears. 
 
 
 
Use the  [FEED]  or [RESTART]  key to select a desired option. 
 
 
 
 
 
 
 
After selecting a Kanji code, press the  [PAUSE] key. 
 
 
(13)  EURO Code Selection 
This parameter is to choose a Euro code...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-23 
2.9.1 Parameter Setting  (Cont.) 
 
 
 
  (14)  Auto Print Head Check Selection 
This parameter is to choose whethe
r to perform the Auto Print Head 
Check function at the power on time.  When “PARAMETER SET” 
appears, press the  [PAUSE] key until the following display appears. 
 
 
 
Use the  [FEED]  or [RESTART]  key to select a desired option. 
 
 
 
 
 
 
 
 
 
After selecting auto print head check, press the...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-24 
2.9.1 Parameter Setting  (Cont.) 
 
 
 
 
  (16)  Web Printer Function Selection 
This parameter is to choose whether to
 use the printer as a web printer.   
When “PARAMETER SET” appears, press the  [PAUSE] key until 
the following display appears. 
 
 
 
Use the  [FEED]  or [RESTART]  key to select a desired option. 
 
 
 
 
 
 
After selecting the Web printer function, press the  [PAUSE] key. 
 
 
(17)  Input...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-25 
2.9.1 Parameter Setting  (Cont.) 
 
  (18)  Expansion I/O Interface Type Selection 
This parameter is to choose a type of the Expansion I/O interface 
operating mode. 
This parameter should be set depe
nding on the expansion I/O control 
specification of the device to be connected via the expansion I/O 
interface.  For details, refer to the  External Equipment Interface 
Specification . 
When “PARAMETER SET”...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-26 
2.9.1 Parameter Setting  (Cont.) 
 
 
  (20)  Label End/Ribbon End Selection 
This parameter is to choose a printing process when a label end or ribbon 
end is detected.   
When “PARAMETER SET” appears, press the 
[PAUSE] key until 
the following display appears. 
 
 
 
Use the  [FEED]  or [RESTART]  key to select a desired option. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
After selecting a Label End type, press the  [PAUSE]...

2. PRINTER SETUP ENGLISH VERSION EO1-33055 
2.9 Setting an Operating Environment
 
E2-27 
2.9.2  Dump Mode Setting 
 While “DUMP MODE” is displayed on the LCD Message Display, 
press the  [PAUSE]  key to enter the Dump Mode. 
In the Dump Mode, data in the receive buffer are printed.  Data are 
expressed in hexadecimal values.  This  operation allows the user to verify 
programming commands or debug the program.  
 
When “DUMP MODE” appears, press the  [PAUSE] key. 
 
 
Use the  [FEED] or [RESTART]  key...