Toshiba B Ex4 User Guide

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 
7.1 Media 
 
E7- 2 
B-EX4T-TS12-QM-R [Unit: mm] 
Cut mode 
Rotary cutter  Label dispensing mode 
Item Batch mode  Strip mode 
Head-up disabled  Head-up enabled Disc cutter 
Label  10.0 – 1500.0 25.4 – 256.0 3”/s.: 94.0 - 1500.0 
5”/s.: 102.0 – 1500.0 
8”/s.: 113.0 – 1500.0 38.0 – 1500.0 
25.4 – 1500.0 c Media pitch 
Tag  10.0 – 1500.0 ---- 3”/s., 5”/s.: 30.0 – 1500.0 
8”/s.: 38.0 – 1494.0 25.4 – 1500.0 
d Label length  6.0 – 1498.0  23.4 – 1498.0 3”/s.:...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 
7.1 Media 
 
E7- 3 
7.1.2  Detection Area of the Transmissive Sensor 
The Transmissive Sensor is movable from the centre to the left edge of media.   
The Transmissive Sensor detects a gap between labels, as illustrated below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Sensor position Area to be detected. Centre of media 
Print side  
Min. 12 mm
Label
Gap
LabelMin. 2.0 mm
(Min. 6.0 mm when using
the  cutter module.)
Sensor is movable 
within this range.
Media...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 
7.1 Media 
 
E7- 4 
7.1.3  Detection Area of the Reflective Sensor 
The Reflective Sensor is movable from the centre to the left edge of media. 
The reflection factor of the Black Mark must be 10% or lower with a waveform length of 950 nm. 
The Reflective Sensor should be aligned with the centre of the Black Mark.   
Rectangular holes can substitute the black marks, on the condition that nothing is printed on the back side. 
 
 
 
 
 
 
7.1.4  Effective...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 
7.1 Media 
 
E7- 5 
7.1.5 RFID Tags 
Available RFID tag types are different depending on the RFID modules, as follows: 
 
„ B-EX700-RFID-U2-US-R and B-EX700-RFID-U2-EU-R 
• EPC UHF Gen2 
• ISO-18000-6C 
 
 
„ B-EX700-RFID-H1-QM-R 
• TAGSYS C210 
• TAGSYS C220 
• TAGSYS C240 
• TAGSYS C320 (Only when the TAGSYS S003 module is used.) 
• I-Code 
• Tag-it 
• ISO15693 
 
 
Cautions for using RFID Tags 
(1) Lift-up of Print Head 
An RFID tag chip or the print...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 
7.1 Media 
 
E7- 6 
(7) Printing on Bump (Chip/Antenna) Area 
Embedding an RFID tag in labels creates bumps on the label surface, causing incomplete printing. 
Uneven printing or incomplete printing can occur easily, especially within 5 mm back and forth, and right and 
left sides of the RFID-tag embedded area, as shown in the figure below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(8) Ambient Temperature 
As low temperature deteriorates wireless...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 7.2 Ribbon 
 
E7- 7 
7.2 Ribbon 
Please make sure that the ribbon being used is approved  by TOSHIBA TEC.  The warranty does not apply to any 
problem caused by using non-approved ribbons. 
For information regarding TOSHIBA TEC appr oved ribbon, please contact a TOSHIBA TEC service 
representative.  
Type Spool type 
Width  41 – 112 mm  Recommended width is 41, 50, 68, 84, and 112 mm. 
Length 600 m 
Outside Diameter φ90 mm (max.) 
 
The table below...

7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089 
7.4 Care/Handling of Media and Ribbon 
E7- 8 
7.3  Recommended Media and Ribbon Types (Cont.) 
Ribbon type  Description 
Smear-less ribbon (Wax resin ribbon)  Good match for coated paper.  The printed image will resist water and 
light rubbing.  
Scratch and solvent resistance ribbon Very good match for plastic films (synthetic paper, PET, polyimide, 
etc.) 
Scratch and solvent resistance 
Heat resistance with PET and polyimide. 
 
Combination of Media...

APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33089 
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 1 
APPENDIX 1  MESSAGES AND LEDS 
Appendix 1 describes the LCD messages displayed on the operation panel.   
Symbols in the message 
1:  : The LED is illuminated.   ~: The LED is flashing.   z: The LED is unlit. 
2:  ****:  the number of unprinted media.  Up to 9999 (in pieces) 
3:  %%,%%%,%%%:  Remaining memory size of the external memory: 0 to 09,999,999 (in K bytes) 
4:  ####:  Remaining memory size for PC...

APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33089 
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 2 
LED IndicationPrinter Status Restoration by 
RESTART key   Acceptance of 
Status Request/
Reset Command 
No. LCD Message 
ONLINE ERROR Yes/No Yes/No 
21 POWER FAILURE z    A power failure has occurred.  No  No 
22 EEPROM ERROR z   Data cannot be read from/written to a 
backup EEPROM properly  No No 
23 SYSTEM ERROR z
   
When the following abnormal 
operations are performed, a system 
error occurs: 
(a)...

APPENDIX 1  MESSAGES AND LEDS ENGLISH VERSION EO1-33089 
APPENDIX 1  MESSAGES AND LEDS
 
EA1- 3 
 
NOTES: 
•  If a command error is found in the command received, up to  42 bytes of the erroneous command, starting from the 
command code, will be displayed.  (However, [LF] and [NUL] will not be displayed.) 
 
 
 
Example 1 
[ESC]PC001;0 A
00,0300,2,2,A,00,B[LF][NUL]  
 Command error 
The following message appears. 
 
 
 
 
 
Example 2 
[ESC]T20 G
30[LF] [NUL]  
 Command error 
The following message...