Tenda Router TEI480T User Manual

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
Password in the dialogue box (the default value for User name and 
Password are “admin”). It is recommended to change the User Name 
and Password when you enter into the system for the first time. 
 
Enter the configuration Interface and on  the left hand side of the page, you 
could see 10 function menus including: Running Status, Wizard, General 
Setting, DHCP Server, Advance Setting ，  Virtual Server, Security Setting, 
Route Setting, System Tool, Logout. When you select the respective button, 
more options would appear. 
4.2 ISP Configuration 
z   This router supports 3 types of  common used access modes to the 
Internet (the default access mode is dynamic IP access): 
PPPoE (ADSL): Using PPPoE dialing up to have Internet connection 
Dynamic IP: Broadband network etc use DHCP services to appoint IP 
addresses 
    10 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
Fixed IP: Ethernet broadband Access, ISP supports fixed IP address 
4.2.1 Wizard 
Please single click the “Next” button in Administrator Mode Interface 
and enter in to the Interface for access mode selection. 
As the figure below, 3 types of common used access modes to Internet are 
displayed, please select according to your requirement: 
 
 
 
 
 
 
 
4.2.1.1 PPPoE (ADSL) 
If you are connecting to the Internet through “ADSL Virtual Dial-up 
(PPPoE)”, please just enter  the User Name and Password which is provided 
by the ISP into the “Wizard ADSL” dialogue box. 
4.2.1.2 Dynamic IP 
If you are using “Dynamic IP” to hav e access to the Internet, you are 
able to obtain dynamic IP address from the ISP to have access to the 
Internet and do not need to have other c onfiguration. Please just click “Next” 
and “save”. 
    11 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
 
4.2.1.3 Static IP 
If you are using “Static IP” to have access to the Internet, please input 
the IP Address, Sub-net mask, Gateway, DNS and secondary DNS, after 
this, please click “Next” to save. 
 
 
 
 
 
 
 
After configuration, please go to “Running Status”>”WAN Status” to 
check the configuration t hat you have set. And by clicking the “disconnect” 
button, you are able to disconnect the Internet connectivity manually, and 
when you press the “connect” button, y ou are able to establish the Internet 
connectivity again. 
 
 
 
 
    12 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
4.3 Configuration 
4.3.1 Start and Log In 
z  After staring and Logging in successfully, the browser would display 
the Interface for administrator’s mode. 
z  In the menu on the left hand si de, there are ten buttons including 
Running Status, Wizard, General Setting, DHCP Server, Advance 
Setting, Virtual Server, Security Se tting, Route Setting, System Tool, 
and Logout. Single click a certain button and you are able to have the 
respective function configuration. 
z   We would give detail introduction to the function of each menu. 
4.3.2 Running Status 
 
 
a. WAN Status 
The connectivity status, WAN IP, Subnet Mask, Gateway, DNS, 
Secondary DNS, Link Type of  the router are displayed here. 
   
13 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
b. LAN Status 
The basic information of IP address, Subnet mask, DHCP Server, NAT, 
Firewall are displayed here. 
c. The Running Status ，Client Count ，Firmware Version etc are displayed 
here. 
4.3.3 General Setting 
Under “General Setting”, you could find 5 sub-items including LAN 
Setting, WAN Setting, MAC Clone, DNS Server, and Access Limit. Please 
single click a certain sub-item and you would be able to have respective 
function configuration. We would give brief introduction as follows: 
4.3.3.1 LAN Setting 
 
z   IP Address: This refers to the IP  address of the router on the LAN. 
Default IP address is 192.168.0.1, you can change this according to 
your requirement. 
z   Netmask: This refers to the SubNet Mask of the router on the LAN, you 
can input it manually. 
 Notice:  If you change this IP address, you are required to use the new 
IP address to log in to the WEB Management Interface, and in order to have 
    14 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
   15 
 
successful access to the Internet, default Gateway of all the computers 
under this router are required to set as this IP address. 
4.3.3.2 WAN Setting 
First, please select the WAN access type, which means your way of 
connecting to the Internet. The default mode of connecting to the Internet is 
“Dynamic IP”  
a.  Dynamic IP: If you are having access to the Internet through dynamic 
IP, you are able to obtain IP address from the ISP automatically. 
b.  Static IP: IF you are having access  to the Internet through static IP, 
you should have the fixed IP address which is provided by your ISP. 
c.  ADSL: If you are having access to  the Internet through ADSL virtual 
dialing up. In this page, you are able to change and configure the 
following items: 
z  User Name ：This refers to your User Name, please input the User 
Name which is provided by your ISP. 
z  Password ：Please input the Password which is provided by your ISP, if 
you are not clear of these informa tion, please contact your ISP and 
require them to offer to you. 
z  Service ：Input the Service which is provi ded by your ISP. (Optional) 
z  MTU: the default value is 1492,  you can change according to your 
requirement. 
z  Connecting automatically ：This enables you to connect automatically 
after starting the router or being disconnected.  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
z Connecting manually ：This enables the user to connect manually. 
z  Connecting if needed ：To set up connection automatically when data 
visiting exists. 
z   Connecting automatically in period of time ：To set up connection at 
fixed time period 
4.3.3.3 MAC Clone 
 
 
 
Selecting this enables you to clone the MAC address of the computer 
being used by the administrator to the MAC address in the WAN port. (You 
could also change the MAC address manually.) 
4.3.3.4 DNS Server 
 
 
 
 
z   DNS server address: Please input  the DNS server address provided 
by ISP. Please contact your ISP for this information if you are not clear. 
z   Secondary DNS: Optional item, if your ISP provides you with two DNS 
servers, then you could input the  IP address of another DNS server 
here. 
 Notice:  The main function of DNS is to translate the URL that we enter 
   
16 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
into IP address. 
4.3.3.5 Access Limit 
In order to enhance the security of the router, you are able to set an IP 
address and change the port of the host which can access to the web 
management interface. 
 
 
 
 
 
 
 
 
 Notice:  After setting the IP address, computers with other IP addresses 
are not able to log in the WEB Manag ement Interface of the router. After 
changing the port through which the hos t is entitled to have access to the 
management interface of the router, yo u are required to restart the router. 
4.3.4 DHCP Server   
In DHCP server, you can see “LAN DHCP Server” and “DHCP Client 
List”. We would have detail descriptions on these two functions as follows: 
4.3.4.1 LAN DHCP Server 
    17 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
 
In order to use the DHCP server function, you should have the following 
configuration: 
z Enable DHCP server  
z  Start IP Address of IP Pool ：The starting IP address which is appointed 
by the DHCP server automatically.  
z  End IP Address of IP Pool: The ending IP address which is appointed 
by the DHCP server automatically  
z  Lease Time: The entitled time for each client to use the IP addressed 
which it obtains.  
 Notice: In order to use the DHCP server function of this router, the 
TCP/IP protocol of the computer s under the LAN should be set as 
“Auto-Obtain IP Address” 
4.3.4.2 DHCP Client List 
z   The name of the host, IP address, MAC Address, Remaining Time and 
Static are displayed in DHCP Client List. 
¾  The name of the host: the name of the host 
¾  IP Address: the IP address which is applied by the client 
¾  MAC Address: the MAC Address of  the computer which applies the IP 
address successfully 
    18 
  
						

							
                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
¾ Remaining Time：The time for the host to use the IP address which is 
permitted by the DHCP server. 
¾ Static ：Bind the IP address to client through MAC address. 
z  When the router uses up the IP address in the IP Pool, it will distribute 
expired IP addresses to clients who newly apply for IP addresses. 
z  Input in the “static client ”, the MAC address will be bind to IP address, 
this enables the computer to obtain current IP address next time. 
 Notice:  When the computers on the LAN  are set as auto obtain, you 
are able to distribute IP addresses to computers on the LAN through this 
function. 
4.3.5 Advance Settings 
z   In the “Advance Setting” menu, t here are six sub-items, including 
Statistic, Port Monitor, VLAN, Bandwidth Control, LAN IP Control and 
ARP Control and load balance. By clicking a certain sub-item, you are 
able to have respective function c hecking and have configuration. 
4.3.5.1 Statistic 
 
 
 
 
 
 
This page displays the traffic and data rate of each host IP. (↑stands for 
transmitting, ↓stands for receiving)  Link Count，Operation and Binding 
   
19