Tenda Router TEI480T User Manual

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
Password in the dialogue box (the default value for User name and 
Password are “admin”). It is recommended to change the User Name 
and Password when you enter into the system for the first time. 
 
Enter the configuration Interface and on  the left hand side of the page, you 
could see 10 function menus including: Running Status, Wizard, General 
Setting, DHCP Server, Advance Setting ，  Virtual Server, Security Setting, 
Route...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
Fixed IP: Ethernet broadband Access, ISP supports fixed IP address 
4.2.1 Wizard 
Please single click the “Next” button in Administrator Mode Interface 
and enter in to the Interface for access mode selection. 
As the figure below, 3 types of common used access modes to Internet are 
displayed, please select according to your requirement: 
 
 
 
 
 
 
 
4.2.1.1 PPPoE (ADSL) 
If you are connecting to the Internet through “ADSL...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
 
4.2.1.3 Static IP 
If you are using “Static IP” to have access to the Internet, please input 
the IP Address, Sub-net mask, Gateway, DNS and secondary DNS, after 
this, please click “Next” to save. 
 
 
 
 
 
 
 
After configuration, please go to “Running Status”>”WAN Status” to 
check the configuration t hat you have set. And by clicking the “disconnect” 
button, you are able to disconnect the Internet connectivity manually,...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
4.3 Configuration 
4.3.1 Start and Log In 
z  After staring and Logging in successfully, the browser would display 
the Interface for administrator’s mode. 
z  In the menu on the left hand si de, there are ten buttons including 
Running Status, Wizard, General Setting, DHCP Server, Advance 
Setting, Virtual Server, Security Se tting, Route Setting, System Tool, 
and Logout. Single click a certain button and you are able to have...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
b. LAN Status 
The basic information of IP address, Subnet mask, DHCP Server, NAT, 
Firewall are displayed here. 
c. The Running Status ，Client Count ，Firmware Version etc are displayed 
here. 
4.3.3 General Setting 
Under “General Setting”, you could find 5 sub-items including LAN 
Setting, WAN Setting, MAC Clone, DNS Server, and Access Limit. Please 
single click a certain sub-item and you would be able to have respective...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
   15 
 
successful access to the Internet, default Gateway of all the computers 
under this router are required to set as this IP address. 
4.3.3.2 WAN Setting 
First, please select the WAN access type, which means your way of 
connecting to the Internet. The default mode of connecting to the Internet is 
“Dynamic IP”  
a.  Dynamic IP: If you are having access to the Internet through dynamic 
IP, you are able to obtain IP address...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
z Connecting manually ：This enables the user to connect manually. 
z  Connecting if needed ：To set up connection automatically when data 
visiting exists. 
z   Connecting automatically in period of time ：To set up connection at 
fixed time period 
4.3.3.3 MAC Clone 
 
 
 
Selecting this enables you to clone the MAC address of the computer 
being used by the administrator to the MAC address in the WAN port. (You 
could also change...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
into IP address. 
4.3.3.5 Access Limit 
In order to enhance the security of the router, you are able to set an IP 
address and change the port of the host which can access to the web 
management interface. 
 
 
 
 
 
 
 
 
 Notice:  After setting the IP address, computers with other IP addresses 
are not able to log in the WEB Manag ement Interface of the router. After 
changing the port through which the hos t is entitled to have...

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
 
In order to use the DHCP server function, you should have the following 
configuration: 
z Enable DHCP server  
z  Start IP Address of IP Pool ：The starting IP address which is appointed 
by the DHCP server automatically.  
z  End IP Address of IP Pool: The ending IP address which is appointed 
by the DHCP server automatically  
z  Lease Time: The entitled time for each client to use the IP addressed 
which it obtains....

                     TEI480T/490T/4000 Enterprise & Net-bar Level Router 
¾ Remaining Time：The time for the host to use the IP address which is 
permitted by the DHCP server. 
¾ Static ：Bind the IP address to client through MAC address. 
z  When the router uses up the IP address in the IP Pool, it will distribute 
expired IP addresses to clients who newly apply for IP addresses. 
z  Input in the “static client ”, the MAC address will be bind to IP address, 
this enables the computer to obtain current IP...