Technics Stereo Power Amplifier Se R1 Owners Manual

							11
English
You can input analog audio signals to this unit and play back music.
*1 Select [BALANCED] or [UNBALANCED]. Set the analog audio input  selector switch to a position that corresponds to the device you want to 
play.
*2 We recommend using cables with a length of 3 m (9.9 ft) or less .
≥When connecting to an analog audio output device, set the input  selector knob to [ANALOG]. (>13)
∫To disconnect the XLR cables
Pull out the XLR cables while pressing [PUSH] at the top of the  terminals.
Connecting to analog audio output devices
e.g.,
Pre-amplifier, etc. This unit
(rear) Pre-amplifier, etc.
Audio cable
(not supplied) XLR cable*
2
(not supplied)
*1


(11)
SE-R1-SQT0505_PP_mst.book  11 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							12
Connect only after all other connections are completed.
∫To disconnect the AC power supply cord from this unit
Pull out the AC power supply cord while pressing the top and bo ttom sides of the connector.
	
≥Although the AC power switch is in the [ ] position, the unit is  not completely disconnected from the mains. Remove the plug from the 
main electrical outlet if you will  not be using the unit for an  extended period of time. Place the unit so the plug can be eas ily removed.
AC power supply cord connection
This unit
(rear)
To a household AC outlet
AC power supply cord (supplied) DO NOT
DO

 
(12)
SE-R1-SQT0505_PP_mst.book  12 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							13
EnglishTo optimize the audio output, you can measure the amplifier 
characteristics and correct its output when it is connected to 
the speakers.
≥Set the speaker selector knob to  a position that corresponds to the 
connected speakers. ( >right)
1Press the unit on/off button to the [ ] 
position.
≥The power indicator lights up in blue.
2Press and hold [LAPC] until the LAPC 
indicator on this unit starts to blink.
≥ This unit will start measuring the characteristics of the 
amplifier. Check that a test tone is output from both the 
left and right speakers.
– If you press [LAPC], turn the speaker selector knob or 
operate other controls while the measurement is in 
progress, it will be canceled. The LAPC indicator on this unit 
will go off.
≥When the measurement is complete, amplifier output 
correction will be automatically turned on. The LAPC 
indicator on this unit will light up.
∫ Turning on/off the output correction 
function
Press [LAPC].
Each time you press the button:
	
≥When the SU-R1 is connected via the system control function, yo u 
can operate using the SU-R1’s remote control.
≥ The output correction setting is applied separately to each spe aker 
terminal option (A/B/A+B).
≥ Depending on the type of the connected speakers, the effect of  the 
output correction function may be minimal.
≥ The corrected output remains in effect until you measure the 
characteristics again. When you use other speakers, redo the 
measurement.
Operations
1Press the unit on/off button to the [ ] 
position.
≥The power indicator lights up in blue.
2Turn the input selector knob.
Select a playback device and gain value.
3Turn the speaker selector knob.
Select the speaker terminals from which audio will be 
output.
4Operate the device to be used for playback.
Measuring the characteristics 
of the amplifier and correcting 
its output
Test tone emitted during measurement
To ensure the measurement accuracy, the speakers 
output a test tone at regular intervals. (For approximately 
4minutes)
It is not possible to change the volume of the audio being 
output while the measurement is in progress.
LAPC indicator lights up On
LAPC indicator goes offOff
ANALOG (dB)
(s 30/ s20/ s10/0) Select an optimal setting for the 
connected device. (
>below)
DIGITAL Select this setting when using 
the system control function.
OFF
Does not output audio.
AOutputs audio from the speakers 
connected to the A terminals.
BOutputs audio from the speakers 
connected to the B terminals.
A+B Outputs audio from the speakers 
connected to the A and B 
terminals.
Input selector knob setting during analog input
≥
For normal operation, set the value to [0].
≥ For playback at low volume levels, lower the gain 
value of this unit by setting the input selector knob to 
[-30], [-20] or [-10] of [ANALOG (dB)]. This will 
minimize analog/digital conversion errors that occur 
on this unit.
(13)
SE-R1-SQT0505_PP_mst.book  13 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							14
You can automatically link this unit with the SU-R1 and 
operate them easily with the remote control of the SU-R1.
Preparation
1Connect this unit and the SU-R1 with cables for system 
control. ( >10)
2 Set the input selector knob to [DIGITAL]. ( >13)
3 Press the unit on/off button on this unit and the SU-R1 to 
the [ ] position.
4 If “Digital Link” is set to “Off” on the SU-R1, change the 
setting to “On”.
∫Switching this unit and the SU-R1 to 
on/standby simultaneously
≥If you point the SU-R1’s remote  control at the SU-R1 and 
press [ Í] when this unit and the SU-R1 are in standby 
mode, this unit and the SU-R1 will be turned on 
simultaneously.
≥ If you point the SU-R1’s remote  control at the SU-R1 and 
press [ Í] when this unit and the SU-R1 are turned on, this 
unit and the SU-R1 will simultaneously enter standby 
mode.
∫ Measuring the characteristics of the 
amplifier and correcting its output
You can operate using the SU-R1’s remote control. ( >13)
	
≥For information on the operations of the SU-R1, please also ref er 
to its operating instructions.
Troubleshooting
Before requesting service, make the following checks. If you 
are uncertain about some of the check points, or if the 
solutions indicated in the following guide does not resolve 
the issue, then consult your dealer for instructions.
Heat buildup of this unit.
≥ This unit becomes warm when the volume is high. This is 
not a malfunction.
A “humming” sound can be heard during playback.
≥An AC power supply cord or fluorescent light is near the 
cables. Keep other appliances and cords away from the 
cables of this unit.
≥ A strong magnetic field near a TV or other device may 
adversely affect the audio quality. Keep this unit away from 
such devices.
≥ The speakers may output noise when a device nearby is 
emitting powerful radio waves, such as when a mobile 
phone is on a call.
No sound.
≥Check connections to speakers and other equipment.
After checking the connections, measure the 
characteristics of the amplifier. ( >13)
≥ Check to see if the correct input source is selected.
≥
Insert the plugs of the cables to be connected all the way in.
≥ Set the speaker selector knob to other than [OFF]. ( >13)
The peak power meter does not operate.
≥In the following cases, this meter does not operate:– When the peak power meter light is turned off by pressing [DIM MER].– When this unit is muted by pressing [MUTE] on the SU-R1’s remote 
control. (Only when the input selector knob is set to [DIGITAL] .)
– When the speaker selector knob is set to [OFF].
The system control function is not working.
≥Connect the cables to the matching LR terminals on this 
unit and the SU-R1.
The unit turns off automatically.
≥Is the auto off function turned on? ( >7)
≥ If the SU-R1 is connected to this unit via the system control 
function, this unit may automatically enter standby mode 
when the SU-R1 enters standby mode. ( >10, 14)
≥
This unit incorporates a protection circuit to prevent damage 
caused by heat buildup. When you use this unit at a high volume  
level for a long period of time, it may turn off automatically.
Wait for this unit to cool down before turning on this unit 
again. (For approximately 3 minutes)
Using the system control 
function
To return all settings to the factory defaults
When the following situations occur, reset the memory:
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
When the unit is off:
1 Press and hold [DIMMER].
2 While continuing to hold [DIMMER], press the unit 
on/off button.
≥Keep holding [DIMMER] until the power indicator and the 
LAPC indicator blink twice.
(14)
SE-R1-SQT0505_PP_mst.book  14 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							15
English
Specifications
	
≥Specifications are subject to change without notice.
≥ Mass and dimensions are approximate.
∫ GENERAL
Power supply AC 120 V, 60 Hz
Power consumption 250 W
Power consumption in standby mode Approx. 0.7 W
Power consumption in off mode Approx. 0.3 W
Dimensions (Wk Hk D) 480 mmk241 mm k567 mm
(18
7/8qk 915/32qk 2211/32q)
Mass (Weight) Approx. 54 kg
(119 lbs)
Operating temperature range 0oC to r 40oC ( r32 oF to  r104 oF)
Operating humidity range 35 % to 80 % RH (no condensation)
∫AMPLIFIER SECTION
FTC output power 150 W r 150 W (20 Hz to 20 kHz, T.H.D. 0.5 %, 8 ≠, 20 kHz LPF)
300 W  r 300 W (20 Hz to 20 kHz, T.H.D. 0.5 %, 4 ≠, 20 kHz LPF)
Frequency response 1 Hz to 90 kHz (s3 dB, 8 ≠)
THD+N 0.05 % (1 kHz, 75 W, 8≠, 20 kHz LPF)
Input sensitivity/Input impedance UNBALANCED 1.2 Vrms / 47 k≠ (ANALOG 0 dB)
BALANCED 1.2 Vrms / 47 k≠ (ANALOG 0 dB)
GAIN 29 dB (ANALOG 0 dB)
Load impedance
A or B, Bi-Wire 4≠ to 16 ≠
A+B 8≠ to 16 ≠
∫TERMINALS SECTION
Analog input
UNBALANCED Pin jack
BALANCED 3 Pin XLR
Digital input Technics Digital Link
(15)
SE-R1-SQT0505_PP_mst.book  15 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							16
Limited Warranty (ONLY FOR U.S.A.)
Technics Products – Limited Warranty
Limited Warranty Coverage
(For USA Only)
If your product does not work properly because of a defect in m aterials or 
workmanship, Panasonic Corporation of North America (referred t o as “the 
warrantor”) will, for the length of the period indicated on the  chart below, which 
starts with the date of original purchase (“warranty period”),  at its option either (a) 
repair your product with new or refurbished parts, (b) replace  it with a new or a 
refurbished equivalent value pr oduct, or (c) refund your purcha se price. The 
decision to repair, replace or refund will be made by the warra ntor.
During the “Labor” warranty period there will be no charge for  labor. During the 
“Parts” warranty period, there  will be no charge for parts. This Limited Warranty 
excludes both parts and labor for non-rechargeable batteries, a ntennas, and 
cosmetic parts (cabinet). This warranty only applies to product s purchased and 
serviced in the United States. This warranty is extended only t o the original 
purchaser of a new product which was not sold “as is”.
Mail-In Service--Online Repair Request
Online Repair Request
To submit a new repair request and for quick repair status visi t our Web Site at 
www.panasonic.com/support.
When shipping the unit, carefully pack, include all supplied ac cessories listed in 
the Owner’s Manual, and send it prepaid, adequately insured and  packed well in 
a carton box. When shipping Lithium Ion batteries please visit  our Web Site at 
www.panasonic.com/BatteryHandling
 as Panasonic is committed to 
providing the most up to date information.  Include a letter detailing the complaint, 
a return address and provide a daytime phone number where you c an be 
reached. A valid registered receipt is required under the Limit ed Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE 
PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits and Exclusions
This warranty ONLY COVERS failures due to defects in materials  or 
workmanship, and DOES NOT COVER normal wear and tear or cosmeti c 
damage. The warranty ALSO DOES NOT COVER damages which occurred  in 
shipment, or failures which are caused by products not supplied  by the 
warrantor, or failures which result from accidents, misuse, abu se, neglect, 
mishandling, misapplication, alteration, faulty installation, 
set-up adjustments, misadjustm ent of consumer controls, imprope r 
maintenance, power line surge, lightning damage, modification,  introduction of 
sand, humidity or liquids, commercial use such as hotel, office , restaurant, or 
other business or rental use of the product, or service by anyo ne other than a 
Factory Service Center or other Authorized Servicer, or damage  that is 
attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER 
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR 
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS 
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes dam
ages for lost time, travel to and from the 
servicer, loss of or damage to media or images, data or other memory or 
recorded content. The items listed are not exclusive, but for i llustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY 
OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED 
WARRANTY.
Some states do not allow the exclusion or limitation of inciden tal or 
consequential damages, or limitations on how long an implied wa rranty lasts, so 
the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also  have other rights 
which vary from state to state. If a problem with this product  develops during or 
after the warranty period, you may contact your dealer or Servi ce Center. If the 
problem is not handled to your satisfaction, then write to: Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy 
Chesapeake, VA 23320
PARTS AND SERVICE, WHICH ARE NO T COVERED BY THIS LIMITED 
WARRANTY, ARE YOUR RESPONSIBILITY.
As of October 2014
Product or Part NamePartsLabor
Technics Stereo Power Amp
5 (five) years 5 (five) years
Technics Audio Control Player
Technics Speaker System
for all your Technics gear
Go to 
www.panasonic.com/accessories
Get everything you need to get the most out of 
your Technics products
Accessories & Parts for your Camera, Phone, A/V 
products, TV, Computers & Networking, Personal  Care, Home Appliances, Headphones, Baeries,  Backup Chargers & more…
Customer Services Directory
For Product Informaon, Operang Assistance, 
Parts, Owner’s Manuals, Dealer and Service info  go to www.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
The model number and serial number of this product can be 
found on either the back or the bottom of the unit.
Please note them in the spac e provided below and keep for 
future reference.
MODEL NUMBER
SE-R1
SERIAL NUMBER
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
(16)
SE-R1-SQT0505_PP_mst.book  16 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							17
English
Limited Warranty (ONLY FOR CANADA)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
TECHNICS PRODUCT – LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a 
period as stated below from the date of original purchase agree s to, at its option either (a) repair your product with new or 
refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The  
decision to repair, replace or refund will be made by Panasonic  Canada Inc. 
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Technics brand 
product mentioned above sold by an authorized Panasonic dealer  in Canada and purchased and used in Canada, which product 
was not sold “as is”, and which product was delivered to you in new condition in the original packaging. 
IN ORDER TO BE ELIGIBLE TO RECE IVE WARRANTY SERVICE HEREUNDER,  A PURCHASE RECEIPT OR OTHER 
PROOF OF DATE OF ORI GINAL PURCHASE, SHOWING  AMOUNT PAID AND PLACE OF PURCHASE
 IS REQUIRED
LIMITATIONS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials  or workmanship, and DOES NOT COVER normal wear and 
tear or cosmetic damage. The warranty ALSO DOES NOT COVER damag es which occurred in shipment, or failures which are 
caused by products not supplied by Panasonic Canada Inc., or fa ilures which result from accidents, misuse, abuse, neglect, 
mishandling, misapplication, alteration, faulty installation, s et-up adjustments, misadjustment of consumer controls, improper  
maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such  as 
hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than an Authorized Servi cer, or 
damage that is attributable to acts of God.
Dry cell batteries are also excluded from coverage under this w arranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTI ES, EXPRESS OR IMPLIED, INCLUDING ANY 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU LAR PURPOSE. IN NO EVENT WILL 
PANASONIC CANADA INC. BE LIABLE  FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING 
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF AN Y EXPRESS OR IMPLIED WARRANTY. (As 
examples, this warranty excludes damages for lost time, travel  to and from the Authorized Servicer, loss of or damage to media  or 
images, data or other memory or recorded content. This list of  items is not exhaustive, but for illustration only.)
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or t he 
exclusion of implied warranties, so the above limitations and e xclusions may not be applicable. This warranty gives you specif ic 
legal rights and you may have other rights which vary depending  on your province or territory.
WARRANTY SERVICE
For product operation, repairs and information assistance , please visit our Support page on:
www.panasonic.ca/english/support
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and prefera bly in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
Technics Stereo Power Amp
5 (five) years parts and labour
Technics Network Audio Control Player
Technics Speaker System
(17)
SE-R1-SQT0505_PP_mst.book  17 ページ  ２０１５年１月２３日　金曜日　午前９時５１分 
						

							4
Nous vous remercions d’avoir arrêté votre choix sur cet appareil.
Il est recommandé de lire attentivement ce manuel avant d’utiliser l’appareil et de le conserver pour consultation ultérieure.
∫Caractéristiques de cet appareil
Cet appareil offre les caractéristiques suivantes :
Amplificateur complètement numérique avec circuit de réduct ion de gigue très précis et circuit de conversion MID
Cet appareil est un amplificateur complète ment numérique. Son circuit de réduction de gigue très précis et son circuit de 
conversion de modulation dimpulsions en durée (MID) éliminent toute dist orsion, bruit ou gigue.
LAPC (Load Adaptive Phase Calibration) (Calibration de phase adaptative de la charge)
La gestion adaptative de limpédance du haut-parleur réduit lam plitude de fréquence et les caractéristiques de la phase. Il en 
résulte une reproduction du son avec  une riche expression spatiale.
Pilote GaN-FET
Une permutation à grande vitesse, sans perte, est nécessaire afin dobtenir une amplific ation pure de signaux MID précisément 
émis. Cest pour cette raison que cet appareil est fourni avec un  pilote GaN-FET haute vitesse avec une résistance en circuit très 
basse.
∫ Dispositifs recommandés
Nous conseillons dutiliser des dispositifs Technics (e n option) afin dobtenir une qualité sonore supérieure.
Pour toute assistance supplémentaire, visiter :
www.panasonic.ca/french/support
Nom du produitNuméro du modèle
Lecteur réseau audio avec commande SU-R1 Enceinte acoustique SB-R1
(18)
SE-R1PP-SQT0505-PP_cfr.book  4 ページ  ２０１５年１月２３日　金曜日　午前１０時１７分 
						

							5
Français (Canada)
IMPORTANTES MISES EN GARDE
Avant d’utiliser l’appareil, lire attentivement les instructions qui suivent. Se conformer tout 
particulièrement aux avertissements inscrits sur l’appareil et aux consignes de sécurité 
indiquées ci-dessous. Conserver le présent manuel pour consultation ultérieure.
1 Lire attentivement ces instructions.
2 Conserver ces instructions.
3 Lire toutes les mises en garde.
4 Suivre toutes les instructions.
5 Ne pas utiliser cet appareil près d’une source d’eau.
6 Ne nettoyer qu’ave c un chiffon sec.
7 Ne pas bloquer les évents d’aération. Installer l’appareil selon les 
instructions du fabricant.
8 Ne pas installer l’appareil près d’un appareil de chauffage tel qu’un  radiateur, une cuisinière, un registre de chaleur ou tout dispositif émettant 
de la chaleur (y compris un amplificateur).
9 Pour des raisons de sécurité, ne pas modifier la fiche polarisée ou celle de  mise à la terre. Une fiche polarisée est une fiche à deux lames, dont une plus 
large. Une fiche de mise à la terre est une fiche à deux lames avec une 
broche de masse. La lame plus large ou la broche de masse procure une 
protection accrue. Si ce genre de fiche ne peut être inséré dans une prise de 
courant, communiquer avec un électricien pour remplacer la prise.
10 S’assurer que le cordon est placé dans un endroit où il ne risque pas d’être écrasé, piétiné ou coincé. Faire particulièrement attention à ses 
extrémités de branchement, y compris sa fiche.
11 N’utiliser que les accessoires ou périphériques recommandés par le fabricant.12 N’utiliser l’appareil qu’avec un chariot, meuble, trépied, support 
ou table recommandé par le fabricant ou vendu avec l’appareil. 
Lors de l’utilisation d’un chariot, le déplacer avec le plus grand 
soin afin d’éviter tout dommage.
13 Débrancher cet appareil lors d’un orage ou en cas de non-utilisation prolongée.
14 Confier l’a ppareil à un technicien qu alifié pour toute 
réparation : cordon d’alimentation ou fiche endommagé, liquide renversé 
ou objet tombé dans  l’appareil, exposition à la pluie ou à une humidité 
excessive, mauvais fonctionnem ent ou échappement de l’appareil.
Appareil≥Pour réduire les risques d’incendie, de choc électrique ou de dommages à 
l’appareil,
– N’exposez pas cet appareil à la pluie, à l’humidité, à l’égouttement ou aux 
éclaboussements.
– Ne placez sur l’appareil aucun objet rempli de liquide, comme par 
exemple des vases.
– Utilisez exclusivement les accessoires recommandés.
– Ne retirez pas les couvercles.
– Toute réparation doit être faite par un personnel qualifié et non par l’usager.– Ne posez pas dobjets lourds sur cet appareil.
Cordon d’alimentation c.a.≥ La fiche d’alimentation permet de déconnecter l’appareil. 
L’appareil doit être installé à proximité d’une prise secteur facile d’accès.
Appareil≥Ne placer aucune source de flamme nue, telles des bougies allumées, sur l’appareil.≥Ne poser aucun objet sur cet appareil. Cet appareil chauffe lorsquil est en marche.≥Ne pas toucher aux prises de sortie  des enceintes avec vos mains ou tout 
autre objet lorsque les enceintes sont sous tension. Selon les conditions 
dutilisation, ceci pourrait vous exposer à de hautes tensions.
Emplacement≥ Pour réduire les risques d’incendie, de choc 
électrique ou de dommages à l’appareil,
– Ne pas installer cet appareil dans une bibliothèque, 
une armoire ou tout autre espace confiné. 
S’assurer que la ventilation de l’appareil est 
adéquate.
– Ne pas obstruer les évents d’aération de l’appareil avec des journaux, des nappes, des 
rideaux ou d’autres objets similaires.
≥ Vous devez être plus dune personne pour 
déplacer ou transporter cet appareil.
≥ Vérifiez que lemplacement choisi est assez 
solide pour supporter le poids de cet appareil 
(> 15).
≥ Ne soulevez pas ou ne transportez pas cet 
appareil en le prenant par ses commutateurs. 
Cela pourrait faire tomber lappareil, mener à des 
blessures ou à des anomalies de 
fonctionnement de cet appareil.
AVERTISSEMENT
ATTENTION
Conforme à la norme CAN/CSA STD C22.2 No.60065.
CE QUI SUIT NE S’APPLIQUE QU’AU CANADA.CAN ICES-3(B)/NMB-3(B)
Information sur la mise au rebut dans les pays 
n’appartenant pas à l’Union européenne
Ce symbole est uniquement valide dans l’Union européenne.
Si vous désirez mettre ce produit au rebut, contactez 
l’administration locale ou le revendeur et informez-vous de la 
bonne façon de procéder.
Le symbole de l’éclair dans un triangle équilatéral
indique la présence d’une tension suffisamment
élevée pour engendrer un risque de chocs
électriques.
AV I S :AFIN DE PRÉVENIR LE RISQUE DE CHOCS 
ÉLECTRIQUES, NE PAS RETIRER LES VIS.
CONFIER TOUTE RÉPARATION
À UN TECHNICIEN QUALIFIÉ.
 
Le point d’exclamation dans un triangle équilatéral indique 
que le manuel d’utilisation inclus avec l’appareil contient 
d’importantes recommandations quant au fonctionnement 
et à l’entretien de ce dernier.
RISQUE DE CHOC ÉLECTRIQUENE PAS OUVRIR      
AVIS
(19)
SE-R1PP-SQT0505-PP_cfr.book  5 ページ  ２０１５年１月２３日　金曜日　午前１０時１７分 
						

							6
Table des matières
Accessoires
(SEULEMENT POUR LE CANADA)
La feuille d’autocollants en français ci-incluse correspond aux noms des touches sur l’appareil.
	
≥Les numéros de produit fournis dans ce manuel  de lutilisateur sont corrects à compter de décembre 2014. Ces numéros peuvent êt re modifiés 
sans préavis.
≥ Ne pas utiliser le cordon d’alim entation avec aucun autre appareil.
Entretien de l’appareil
Débrancher le cordon d’alimentation avant de procéder à l’entreti en de l’appareil. Nettoyer cet appareil avec un chiffon doux.≥Si lappareil est particulièrement sale, ut iliser un chiffon humide bien essoré pour  essuyer la saleté, puis essuyer lappareil avec un chiffon doux.
≥ Ne pas utiliser de solvants tels que la benzine, du diluant, de  lalcool, des détergents de cuisine, etc. Cela pourrait modifier lapparence du 
boîtier externe ou décoller son revêtement.
IMPORTANTES MISES EN GARDE .... ................................5
Accessoires.........................................................................6
Entretien de l’appareil ........................................................6
Guide de référence .............................................................7
Préparatifs ...........................................................................8 Fonctionnement ............................................................... 13
Guide de dépannage ........................................................ 14
Spécifications ................................................................... 15
Certificat de garantie limitée ........................................... 16
À propos des illustrations dans le présent manuel
≥ Les pages à consulter sont indiquées par “ @±±”.
≥ Les illustrations peuvent être différentes de l’apparence réelle de l’appareil.
∏ 1 cordon d’alimentation
(K2CB2YY00107)
(20)
SE-R1PP-SQT0505-PP_cfr.book  6 ページ  ２０１５年１月２３日　金曜日　午前１０時１７分