Home > Tascam > Software > Tascam Viewnet MX Graphic Interface Network MX-2424 Owners Manual

Tascam Viewnet MX Graphic Interface Network MX-2424 Owners Manual

Here you can view all the pages of manual Tascam Viewnet MX Graphic Interface Network MX-2424 Owners Manual. The Tascam manuals for Software are available online for free. You can easily download all the documents as PDF.

Page 81

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 81
000 Basic Setup
This menu bank has settings for the most fundamental settings governing how the MX-2424 responds to
external clocks and control. The items in this bank are:
• 
Control Mode
• 
Frame Reference
• 
Sample Reference
• 
Sample Ref Status
• 
Timecode Type
• 
Sample Rate
• 
Varispeed Rate
Control Mode
The control mode governs what signal source controls the MX 2424’s transport functions. The control
mode choices are described below.
Local/...

Page 82

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 82
 MTC Chase
When MTC Chase is active and the unit is online, the MX-2424 will chase incoming Midi Time Code.
Varispeed
Varispeed mode allows for setting playback speed within a range of 87.5% to 112.5% of nominal play
speed.  Varispeed varies the playback frequency as well as the digital sample clock on the digital output.
Frame Reference
These settings determine the source of the MX-2424’s video frame reference signal.
Automatic
Sets the unit to...

Page 83

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 83
Timecode Type
The following timecode types are provided as choices in this setting:
• 
30ND (default)
• 
30DF
• 
25/25
• 
24/24
• 
29ND
• 
29DF
Sample Rate
The following digital sample rates are provided as choices in this setting:
• 
44056 (44100-)
• 
44100
• 
44144 (44100+)
• 
47952 (4800-)
• 
48000 (default)
• 
48048 (4800+)
Varispeed Rate
This setting allows for setting a varispeed playback rate. This function allows playback of audio over a...

Page 84

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 84
100 Bus Control
TLBus Request
Sets the status request for the MX2424on the  TL Bus.
ƒ 
Off The MX2424 will not be active on the TLBus (default).
ƒ 
Slave The MX2424will request to be a Slave on the TL Bus.
ƒ 
Master The MX2424will request to be the Master on the TL Bus.
TL Bus Assigned
This setting shows the status assigned for the MX 2424unit on the TL-Bus. Since there can be only one
TL-Bus Master at a time, it is possible that some units will be...

Page 85

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 85
Ident Request
Sets the TL Bus unit ID (Ident) request for the.MX 2424. This value can be any number between  01 and
32, or can be set to Auto, which is the default. When Auto request is on, the system will automatically
assign ID numbers to the machines on the TL-Bus.
Ident Assigned
 This is a status display of the MX 2424’s TL Bus ID number. 

Page 86

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 86
200 Transport
Record Mode
Sets the record mode on the MX 2424.
Non-destructive
Sets the MX 2424 to non-destructive record mode. In non-destructive record mode, every new recording
creates a new audio file on the disk, and recordings can be undone with the Undo button. (Default
setting)
Tape Mode
Sets the MX 2424 to TapeMode, also called Destructive record mode. In TapeMode, each track is always
a single audio file, no matter how many punch in and out...

Page 87

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 87
Loop Record
Sets the behavior of the MX 2424 during Loop Record operation.
ƒ 
Auto Unload On/Off
With this setting on, the MX 2424 will create a new virtual track each time a record operation is
performed. This is done by unloading the track last recorded on before recording a new one. The MX
defaults to Auto Unload Off.
Pre-roll
Sets the amount of time before the In point (called the pre-roll amount) used for loop play and record
functions. The...

Page 88

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 88
300 Midi
This  setting  allows the Midi Device ID of the MX 2424 to be set. The default is 74. 

Page 89

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 89
400 Input/Output
Inputs 1-8
Inputs 9-16
Inputs 17-24
These settings allow selection of input source for each group of eight channels.
Analog
When selected, input to tracks are taken from the corresponding inputs of the analog I/O module (IF-
AN24) if installed.
Digital In
When selected, input to tracks are taken from the corresponding inputs of a digital I/O module (IF-AE24,
IF-AD24, IF-TD24). 

Page 90

ViewNet MX
ViewNet MX Version 1.1/1.5 Owners Manual 90
2 Channel in
When selected, the dedicated stereo digital inputs are routed to a group of eight tracks, with the left input
routed to the odd-numbered tracks (1,3,5,7), and the right input routed to the even-numbered tracks
(2,4,6,8).  In addition to this menu, it will be necessary to choose which stereo digital I/O to use in menu
462, and to select 2CH as the Sample Reference in Menu 002.
Analog 1-8
When selected, input to tracks are taken from...
Start reading Tascam Viewnet MX Graphic Interface Network MX-2424 Owners Manual
All Tascam manuals