Tascam Dual Cd Player CD-X1500 Owners Manual

							»
CD-X1500
DUAL CD PLAYER
OWNER’S MANUAL / MANUAL DEL USUARIO
D00783300A 
						

							English IMPORTANT SAFETY PRECAUTIONS
2TASCAM  CD-X1500  DUAL CD PLAYER
IMPORTANT (for U.K. Customers)
DO NOT cut off the mains plug from this
equipment.
DO NOT cut off the mains plug from this
equipment.
If the plug fitted is not suitable for the power points
in your home or the cable is too short to reach a
power point, then obtain an appropriate safety
approved extension lead or consult your dealer.
If nonetheless the mains plug is cut of
f, remove the
fuse anddispose of the plugimmediately, to avoid
a possible shock hazard by inadvertent connection
to the mains supply.
If this product is not provided with a mains plug, or
one has to be fitted, then follow the instructions
given below:
IMPORTANT:DO NOT make any connection to
the larger terminal which is marked with the letter
E or by the safety earth symbol c or coloured
GREEN or GREEN-and-YELLOW.
The wires in the mains lead on this product are
coloured in accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As these colours may not correspond with the
coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured BLUE must be
connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be
connected to the terminal which is marked with the
letter L or coloured RED.
When replacing the fuse only a correctly rated
approved type should be used and be sure to re-fit
the fuse cover.
IF IN DOUBT — CONSULT A COMPETENT
ELECTRICIAN.TO THE USER
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may
cause harmful interference to radio
communications.
Operation of this equipment in a residental area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
CAUTION
Changes or modifications to this equipment not
expressly approved by TEAC CORPORATION for
compliance could void the users authority to
operate this equipment.
For U.S.A
For the consumers in Europe
WARNING
This is a Class A product. In a domestic environment,
this product may cause radio interference in which
case the user may be required to take adequate
measures.
Pour les utilisateurs en Europe
AVERTISSEMENT
Il s’agit d’un appareil de Classe A. Dans un
environnement domestique, cet appareil peut
provoquer des interférences radio. Dans ce cas,
l’utilisateur peut être amené à prendre des mesures
appropriées.
Fur Kunden in Europa
Warnung
Dies is eine Einrichtung, welche die Funk-Entstörung
nach Klasse A besitzt. Diese Einrichtung kann im
Wohnbereich Funkstörungen versursachen ; in
diesem Fall kann vom Betrieber verlang werden,
angemessene Maßnahmen durchzführen und dafür
aufzukommen. 
						

							IMPORTANT SAFETY INSTRUCTIONS (1) English
TASCAM  CD-X1500  DUAL CD PLAYER  3
1Read these instructions.
2Keep these instructions.
3Heed all warnings.
4Follow all instructions.
5Do not use this apparatus near water.
6Clean only with dry cloth.
7Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
…Do not expose this apparatus to drips or splashes.
…Do not place any objects filled with liquids, such as
vases, on the apparatus.
…Do not install this apparatus in a confined space such
as a book case or similar unit.
…The apparatus draws nominal non-operating power
from the AC outlet with its POWER switch in the off
position. 
						

							4TASCAM  CD-X1500  DUAL CD PLAYER
SAFETY INFORMATION
This product has been designed and manufactured according to FDA regulations title 21, CFR, chapter 1, subchapter J,
based on the Radiation Control for Health and Safety Act of 1968, and is classified as a class 1 laser product. There is no
hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is
completely confined in the protective housings.
The label required in this regulation is shown 1.
CAUTION
-DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREWDRIVER.
-USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
-IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR NEAREST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE THE
PRODUCT IN ITS DAMAGED STATE.
Optical pickup:Type :  KSS-213C
Manufacturer :  SONY Corporation
Laser output :  Less than 0.4 mW on the objective lens
Wavelength :  760 - 800nm
English IMPORTANT SAFETY INSTRUCTIONS (2) 
						

							Table of contents English
TASCAM  CD-X1500  DUAL CD PLAYER  5
1. Before you start............................................... 6
1.1 Environmental conditions .......................... 6
1.2 Beware of condensation ............................. 6
1.3 Handling of discs ....................................... 6
2. Functions and Controls ................................... 7
2.1 Main Unit (Front Panel) ............................. 7
2.2 Main Unit (Rear Panel) .............................. 7
2.3 Remote Controller (Top Panel) .................. 8
2.4 Remote Controller (Bottom Panel) .......... 10
2.5 Remote Controller (LCD) ........................ 10
3. Playback operation ........................................ 12
3.1 CUE .......................................................... 12
To memorize the CUE point ....................... 12
Stutter play with CUE key .......................... 12
3.2 CUE 1-3 ................................................... 12
To memorize the CUE 1-3 points ............... 12
Stutter play with CUE 1-3 keys .................. 12
3.3 Flash Start ................................................ 12
3.4 A-B  Looping ............................................ 13
To store the LOOP points ............................ 13
Disengage the loop ...................................... 13
Re-looping ................................................... 13
Erasing the LOOP points............................. 13
Changing the LOOP end point (B point) .... 13
3.5 Adjusting the tempo ................................. 14
Tempo range ................................................ 14
Using the TEMPO slider ............................. 14
Using the TAP key....................................... 14
3.6 Pitch bending............................................ 14
3.7 Key original.............................................. 144. More advanced operation.............................. 15
4.1 Key control............................................... 15
4.2 Scratching................................................. 15
4.3 Brake ........................................................ 15
Set the brake time ........................................ 15
4.4 FILTER..................................................... 15
4.5 Track Memory / Recall ............................ 16
Track memory ............................................. 16
Recall ........................................................... 16
4.6 Fader Start ................................................ 17
4.7 Relay Play ................................................ 17
4.8 Auto  Cue .................................................. 17
4.9 Auto  Ready............................................... 17
4.10 Programmed Play ................................... 18
Create the program ...................................... 18
Edit program ................................................ 18
Insert program ............................................. 18
Delete program ............................................ 19
4.11 Preset menu ............................................ 19
4.12 Backup memory ..................................... 20
5. Specifications ................................................ 21
Error Messages ............................................... 21
Demensions ...........................................Back page 
						

							English 1. Before you start
6TASCAM  CD-X1500  DUAL CD PLAYER
1.1 Environmental conditions
The TASCAM CD-X1500 may be used in most
areas, but to maintain top performance, and
prolong operating life, observe the following
environmental conditions:
The nominal temperature should be between 5°C
and 35°C (41°F and 95°F).
Relative humidity should be 30 to 90 degrees non-
condensing.
Make sure that the drive unit is mounted in a level
position for correct operation.
The units should be mounted, using the supplied
rack mounting kits. A typical configuration is
shown below, but other configurations are
possible:
…If the disc trays are more than 5 degrees
away from the horizontal, they will not
open or close.
…Do not install this apparatus in a  con-
fined space such as a book case or simi-
lar unit.
1.2 Beware of condensation
If the player (or a compact disc) is moved from a
cold to a warm place, or used after a sudden
temperature change, there is a danger of
condensation; vapor in the air could condense on
the internal mechanism, making correct operation
impossible. To prevent this, or if this occurs, leave
the player for one or two hours with the power
turned on, then turn the power off and on again.
NOTE
1.3 Handling of discs
The unit has been designed specifically for
reproduction of discs bearing the  mark. No
other discs can be reproduced.
Observe the following:
•Always place the compact discs in the trays with
their label facing upward (compact discs can
only be played on one side).
•To remove a disc from its storage case, press
down on the center of the case, and lift the disc
out, holding it carefully by the edges.
•Finger marks and dust should be carefully wiped
off the discs recorded surface with a soft cloth.
Unlike conventional records, the compact disc
has no grooves to collect dust and microscopic
debris, so gently wiping with a soft cloth should
remove most particles.
•Wipe in a straight motion from the inside to the
outside of the disc. Small dust particles and light
stains will have absolutely no effect on reproduc-
tion quality.
•Never use such chemicals as record sprays, anti-
static sprays or fluid, benzine or thinner to clean
compact discs. Such chemicals will do irrepara-
ble damage to the discs plastic surface.
•Discs should be returned to their cases after use
to avoid serious scratches that could cause the
laser pickup to skip.
•Dont expose discs to direct sunlight or high
humidity and temperature for extended periods.
Long exposure to high temperature can warp the
disc.
•Only use circular compact discs. Avoid using
non-circular promotional, etc. discs.
•To keep the laser pickups clean, dont touch
them. For the same reason, dont leave the disc
trays open unnecessarily. 
						

							2. Functions and Controls English
TASCAM  CD-X1500  DUAL CD PLAYER  7
2-1. Main Unit (Front Panel)
1POWER switch
Turns the power on and off.  The tray LEDs light
when power is supplied.
When Timer start function is on, playback begins
when power is supplied.
2Disc trays
Insert CD into these trays, label side upwards.3Tray LEDs
Lights when power is supplied.
4OPEN keys
Open and close the appropriate tray.
…These keys cannot be used when direct
mode (Preset menu) is off and disc is
being played back.
NOTE
2-2. Main Unit (Rear Panel)
5OUTPUT jacks (RCA)
RCA connectors providing line level output
signals, one set each for discs 1 and 2.
6DIGITAL OUTPUT (COAXIAL, S/PDIF)
Coaxial connectors provide digital output signals.
These connectors can output the 44.1KHz digital
signals constantly even if pitch control is activated.
7FADER START jacks (MINI jack) 
CD-X1500 can be controlled using the external
Fader start command through these jacks.  Connect
the mixer which supports the fader start function
with appropriate cable as well as audio signal.
(TIP: Start, GND: back cue)8ACCESSORY (MINI DIN 6P)
Connect the optional scratch controller TT-M1.
9REMOTE (MINI DIN 8P)
Use this connector to connect the remote control
unit.
…DO NOT use any cable with the CD-
X1500 except the cable supplied with
the unit.
…Connect the cable in the way shown on
the illustration on the rear panel of the
CD-X1500. If you connect the cable in
any other way, you may damage the CD-
X1500.
WARNING 
						

							English 2. Functions and Controls
8TASCAM  CD-X1500  DUAL CD PLAYER
2-3. Remote Controller (Top Panel)
0OPEN key
Opens and closes the appropriate tray.
…These keys cannot be used when direct
mode (Preset menu) is off and a disc is
being played back.
qSEARCH key
Turns on or off the Search function on the Jog
wheel.  When this key is lit, the Jog wheel acts as
a search dial.  After 5 seconds without search
operation, the unit will exit the search mode
automatically.
wP.MODE / PGM key
Selects the play mode, either continuous play (all
play), single play (1 track play), or programmed
play.
Continuous play: No indication in the
LCD
Single play: SINGLE indicator in the
LCD will light
Programmed play: PROGRAM indicator in
the LCD will light
Pressing and holding the TIME/ENTER/SHIFT
key while pressing the P.MODE key, enters
program edit mode.
NOTE
eTIME/ENT / SHIFT key
Selects the time display mode, either elapsed,
remain, or total remain. 
ELAPSED:Elapsed time will show in the
numerical portion in display, but no
additional indicator will light.
REMAIN: REMAIN indicator in the LCD will
light
TOTALREMAIN: The track number display area
shows the number of tracks of
inserted disc, however, for 5 seconds
in the end of track, the current track
number flashes and for 5 seconds in
the beginning of the track, the
current track number lights.
Another function of this key is the modifier key
(SHIFT function). Holding SHIFT while pressing
another key performs the following functions;
SHIFT + P.MODE: Program edit
SHIFT + FLASH: Track memory recall
SHIFT + SET: Track memory
SHIFT + TEMPO: Memory bank select
SHIFT + BEND -: Auto cue on/off
SHIFT + BEND +: Auto ready on/off
SHIFT + TAP: Parameter display select
SHIFT + Jog Wheel: Preset
SHIFT + B: Loop end point edit
SHIFT + CUE: Select the CUE key’s
operation 
						

							2. Functions and Controls English
TASCAM  CD-X1500  DUAL CD PLAYER  9
rLCD
Displays visual feedback for CD-X1500 functions.
tTAP / DISPLAY key
Set the tempo in BPM by tapping this key.  When
you press this key, the parameter counter mode
momentarily changes to TAP BPM display mode.
(∑page 14)
Pressing and holding the SHIFT key while
pressing this key selects the parameter display
mode.
TEMPO ∑KEY∑TA P
yJog Wheel
The following functions can be controlled by the
Jog wheel.
•Search
•Pitch Bend
•Scratch
•Brake time
•Key control
•Preset menu
•FILTER
•Program edit
•Track memory number select
uSCRATCH key
Turns the scratch play mode on and off.  When
scratch play mode is on, this key lights and scratch
can be performed by Jog wheel. (∑page 15)
iFILTER key
Turns the filter effect (FILTER) on and off.  When
the filter effect is activated, this key lights.  The
frequency of the filter can be controlled by Jog
wheel. (∑page 15)
oFLASH / RECALL / DEL key
Turns the flash start mode on and off. (∑page 12) 
Recalls the track memory data. (∑page 16)
Deletes the current selected song from the program
list. (∑page 19)
pSET / MEMO / INS key
Set the cue points with CUE 1-3. (∑page 12)
Memorizes the track memory data (∑page 16)
Adds the current selected song to the program list.
(∑page 18)aCUE 1-3 keys
Depending on the setting, these keys locate to cue
points, flash start from cue points (default), or
stutter play from cue points. (∑page 12)
sCUE key
Locates to the cue point, then pauses.
Stutter play can be performed with this key. (∑
page 12)
Selects the CUE key’s operation mode. (∑page
12)
dPLAY/PAUSE key
Changes the playback mode between playback and
pause.
The light stays on solid in playback mode, and
flashes in pause mode.
fTrack Skip keys
Use these to perform track searches.
gLOOP, A, and B keys
Sets or erases the loop points, or engages or
disengages the loop playing. (∑page 14)
hBEND +/ A.RDY, –/A.CUE keys
Use these keys to perform pitch bending. (∑page
14)
Turns the AUTO CUE function on and off. (∑
page 17)
Turns the AUTO READY function on and off. (∑
page 17)
jTEMPO / BANK key
Selects the tempo range, either +/-8, 16, 32, 100 or
0%. 
Selects the track memory bank from A to E. (∑
page 16)
kKEY ORIG / KEY key
Turns the KEY ORIGINAL function on and off.
(∑page 14)
Sets the key control value. (∑page 15)
lBRAKE / RELAY key
Turns the brake function on and off and sets the
brake time using the Jog wheel. (∑page 15)
Turns the relay play on and off. (∑page 17)
;TEMPO slider
Changes the playback tempo. 
						

							English 2. Functions and Controls
10TASCAM  CD-X1500  DUAL CD PLAYER
zRemote Connector
Connect this to the REMOTE connector on the rear
panel of the main unit.
…DO NOT use any cable except the cable
supplied with the CD-X1500.
WARNING
…Connect the cable to the CD-X1500
shown on the illustration on the rear
panel. If you connect the cable in any
other way, you may damage the CD-
X1500.
2-4. Remote Controller (Bottom Panel)
2-5. Remote Controller (LCD)
xM indicator
If there is track memory data for the current
selected track in the current selected memory bank,
this indicator lights.
cTRACK indicator
vREMAIN indicator
When the time mode is set to remain time mode,
this indicator lights.bSINGLE indicator
When the play mode is set to single play, this
indicator lights.
nPGM indicator
When the play mode is set to programmed play,
this indicator lights.
mTime display
This section is used to show track number, time
values or messages.