Tascam Digital Mixing Console DM-24 Owners Manual

17 – Specifications—Messages and troubleshooting
 TASCAM DM-24 Reference Manual 131
✖Digital input X: Fs convert On
Can’t select Master Clock.
Press ENTER to continue.An attempt has been made to use a digital input as a word sync clock source, 
but the sampling frequency conversion is turned on, preventing this input from 
being used as a clock source (“CLOCK settings” on page 24).
✔DIGITAL INPUT1(XLR) set to master clock
Press ENTER to continue.Warning message sent when Digital input is set as master...

17 – Specifications—Messages and troubleshooting
132 TASCAM DM-24 Reference Manual
●LOCATE TIME 0
00 : 00 : 00.00 ABSThe popup that appears when a location memory is selected (“Location memo-
ries” on page 85).
✔Machine Control List Full
Press ENTER to continue.No more than 16 devices can be input in the Machine Control List (“Selecting 
devices for control” on page 80).
✖Master clock has gone out of range.
        Console muted.
Press ENTER to continue.The master clock frequency has gone outside...

17 – Specifications—Messages and troubleshooting
 TASCAM DM-24 Reference Manual 133
✔OK to overwrite Automation Bank01?
Press ENTER to confirm,
or a cursor key to cancel.Shown when requesting the storage of automation data to a bank already con-
taining data.
✔OK to Overwrite COMP Library024
            from CH2?
Press ENTER to confirm,
or a cursor key to cancel.Data already exists in compressor library entry xxx as an attempt is made to 
store the EQ data from channel y (“Library functions” on page...

17 – Specifications—Messages and troubleshooting
134 TASCAM DM-24 Reference Manual
✔Recall Automation Bank01?
Current data will be erased.
Press ENTER to confirm,
or a cursor key to cancel.Shown when requesting the recall of an automation memory bank.
✔Return x is input into Chyy
Press ENTER to continue.An attempt has been made to assign a return to a channel, when it has already 
been assigned to a channel (“Assignable sends” on page 37).
●Scanning for cascade slave...Displayed by cascade master when...

17 – Specifications—Messages and troubleshooting
 TASCAM DM-24 Reference Manual 135
✔Signal Info: Digital out1
Format: AES/EBU
Contents: Audio
Emphasis: None 
Channel Mode: Two channel
Fs: 44.1kHz
Word Length: 24bit
Press ENTER to continue.Sample popup information screen for AES/EBU data transmitted from a DIGI-
TAL OUT (“CLOCK settings” on page 24).
✔Signal Info: INTERNAL
     Fs: xxxxkHz
Press ENTER to confirm,
or a cursor key to cancel.The information screen given when the master clock is selected...

17 – Specifications—Messages and troubleshooting
136 TASCAM DM-24 Reference Manual
✔Signal Info: Word
New clock source is out of range,
Master clock is unchanged.
Press ENTER to continue.An attempt has been made to select a new clock source, which is out of range 
(“CLOCK settings” on page 24).
✖SLOT1 Card is Unknown
Check Card Type
Press ENTER key to continue.The DM-24 cannot recognize the card fitted in the optional slot. Check the card 
and its installation in the DM-24. Contact your TASCAM dealer for...

17 – Specifications—Messages and troubleshooting
 TASCAM DM-24 Reference Manual 137
✔There are no copy parameters
Press ENTER to continue.Shown when an attempt is made to copy parameters in the UTILITY PARAM. 
COPY screen (“UTILITY copying” on page 62) but no parameters have been 
set.
✔Unmatched Fs.
Do not show this message in the future?
Press ENTER to confirm,
or a cursor key to cancel.Shown when the stored sampling frequency does not match the current sam-
pling frequency (automation data recall)...

17 – Specifications—Block diagram (normal sampling frequency)
138 TASCAM DM-24 Reference Manual
Block diagram (normal sampling frequency)




	




































	


	

 	

 !

 
 

 






#	$
#	$ 




!





 

% &

 !
	






	

()*+,-./

!...

17 – Specifications—Block diagram (high sampling frequency)
 TASCAM DM-24 Reference Manual 139
Block diagram (high sampling frequency)


	

































	

 	

 &

 



 






#	$
#	$ 




&





 

% &
	






	
#

()*+,-./


-















...

17 – Specifications—Level diagram
140 TASCAM DM-24 Reference Manual
Level diagram
7.
7.
.
 .
 .
 %.
 &.
 .
 !.
 3.
7.
7.
.
 .
 .
 %.
 &.
 .
 !.
 3.
7.
7.
.
 .
 .
7.
7.
.
 .
 .
.
 .
 .
 %.
 &.
 . 0
1




	


.
 !
.
 .
 .
 %. 0
1
.
 !

	 0-1081
0-1 081

	
738
 %%8 78
 8
 &8
 !8
		
	 !& 
01
0
1


 8 09!1
 &
738
7&8
 ...