Stihl Fs 130 R Manual

FS 130, FS 130 R
English
19 The following STIHL attachments may 
be mounted to the basic power tool:Mounting Bike Handle with Swivelling 
Handle Support
The machine is supplied with the 
swiveling handle support already 
mounted on the shaft. To mount the 
handlebar it is necessary to remove the 
clamp moldings.
Removing the clamp moldings
NHold the lower clamp (1) and upper 
clamp (2) firmly together.
NRelease the wing screw (3) – the 
clamps are loose once the wing 
screw has been released. They are...

FS 130, FS 130 R
English
20 NPlace the secured assembly on the 
handle support (8) with the wing 
screw at the side nearest the 
engine.
NPush the wing screw into the handle 
support as far as stop and then 
screw it down – but do not finally 
tighten yet.
NLine up the handlebar at a right 
angle to the drive tube – check 
distance A again.
NTighten down the wing screw firmly.Mounting the control handle
NTake out the screw (9) – the nut (10) 
remains in the control handle (11).
NPush the control handle...

FS 130, FS 130 R
English
21 Swivelling the handlebar
Transport position
NLoosen the wing screw (3) and 
unscrew it until the handlebar (7) 
can be turned clockwise.
NTurn the handlebar 90° and then 
swing the handles down.
NTighten down the wing screw (3) 
firmly.
Working position
NReverse the sequence described 
above to swing the handles up and 
turn the handlebar 
counterclockwise.
Mounting Loop Handle with Barrier Bar
NFit the square nuts (1) in the barrier 
bar (2); the holes must line up.NPlace the...

FS 130, FS 130 R
English
22 Mounting the Loop Handle without 
Barrier Bar
NPlace the clamp (3) in the loop 
handle (4) and position them both 
against the drive tube (5).
NPosition the clamp (6) against the 
drive tube.
NLine up the holes.
NFit washers (8) on the screws (7) 
and insert the screws in the holes. 
Fit the square nuts (1) and screw 
them down as far as stop.
NGo to "Securing the Loop Handle".
Securing the Loop Handle
The loop handle can be adjusted to suit 
the height and reach of...

FS 130, FS 130 R
English
23 The carrying ring comes standard with 
the machine or is available as a special 
accessory.
For position of carrying ring see "Main 
Parts".
NPlace the clamp (1) against the 
drive tube with the tapped hole on 
the left (viewed from engine).
NSqueeze the two ends of the clamp 
together and hold in that position.
NInsert the M6x14 screw (2).
NLine up the carrying ring.
NTighten down the screw firmly.
Mounting the Deflector
1Deflector for mowing attachments
2Deflector...

FS 130, FS 130 R
English
24
Mounting the Limit Stop
WARNING
Always fit the limit stop (6) when you use 
a circular saw blade.
NPosition the limit stop (6) on the 
gearbox flange.
NInsert the screws (7) and tighten 
them down firmly.
Placing power tool on the ground
NShut off the engine.
NLay your power tool on its back so 
that the cutting attachment 
mounting face is pointing up.
Mounting Hardware for Cutting 
Attachments
The mounting hardware supplied 
depends on the cutting attachment that 
comes as...

FS 130, FS 130 R
English
25
Blocking the Shaft
The output shaft (2) must be blocked 
with the stop pin (6) or screwdriver (6) to 
mount or remove cutting tools. These 
parts come standard with the machine or 
are available as special accessories.
NInsert the stop pin (6) or 
screwdriver (6) in the hole (7) in the 
gearbox as far as stop – and apply 
slight pressure.
NRotate shaft, nut or cutting 
attachment until the stop pin slips 
into position and blocks the shaft.Removing the Mounting Hardware
NBlock...

FS 130, FS 130 R
English
26
Mounting Metal Cutting Attachment
Keep the leaflet and packaging of the 
metal cutting attachment in a safe place.
WARNING
Wear protective gloves to reduce the 
risk of direct contact with the sharp 
cutting edges.
Mount only one metal cutting 
attachment.
Check direction of rotation of cutting 
attachment
Cutting attachments 1 and 4 may be 
mounted either way round – they must 
be turned over regularly to help avoid 
one-sided wear.
The cutting edges of cutting 
attachments...

FS 130, FS 130 R
English
27 This engine is certified to operate on 
unleaded gasoline and the STIHL two-
stroke engine oil at a mix ratio of 50:1.
Your engine requires a mixture of high-
quality gasoline and two-stroke air 
cooled engine oil.
Use mid-grade unleaded gasoline with a 
minimum octane rating of 89 ((R+M)/2) 
and no more than 10% ethanol content.
Fuel with a lower octane rating may 
increase engine temperatures. This, in 
turn, increases the risk of piston seizure 
and damage to the engine....

FS 130, FS 130 R
English
28 Dispose of empty mixing-oil containers 
only at authorized disposal locations.
Preparations
NBefore fueling, clean the filler cap 
and the area around it to ensure that 
no dirt falls into the tank.
Always thoroughly shake the mixture in 
the canister before fueling your 
machine.
NPosition the machine so that the 
filler cap is facing up.
WARNING
In order to reduce the risk of fire and 
personal injury from escaping gas vapor 
and fumes, remove the fuel filler cap 
carefully...