Stihl 181 C Manual

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
59 Rollomatic E guide bars – MS 171, 
MS 171 C, MS 181, MS 181 C
Actual cutting length will be less than 
listed bar length.
Rollomatic E guide bars – MS 211, 
MS 211 C
Actual cutting length will be less than 
listed bar length.
Rollomatic E Light guide bars – MS 211, 
MS 211 C
Actual cutting length will be less than 
listed bar length.Saw chain 3/8" P – MS 171, MS 171 C, 
MS 181, MS 181 C
Saw chain 3/8" P – MS 211, MS 211 C
Chain sprocket – MS 171, MS 171 C, 
MS 181, MS 181 C
Chain sprocket – MS 211, MS 211 C
To comply with the 45 degree computed 
kickback angle requirement of Section 
5.11 of ANSI/OPEI B175.1-2012, use 
replacement saw chains listed above or 
elsewhere by STIHL as conforming with 
that requirement when used on this 
model chain saw or use saw chains 
classified as "low kickback" in 
accordance with 
ANSI/OPEI B175.1-2012.Since new bar/chain combinations may 
be developed after publication of this 
Manual, ask your STIHL dealer for the 
latest STIHL recommendations. Reduced kickback STIHL guide bars 
(with green label)
Bar lengths: 30, 35, 40 cm (12, 14, 
16 in.)
Pitch: 3/8" P (9.32 mm)
Groove width: 1.1 mm (0.043 in)
Sprocket nose: 7-tooth
Reduced kickback STIHL guide bars 
(with green label)
Bar lengths: 30, 35, 40 cm (12, 14, 
16 in.)
Pitch: 3/8" P (9.32 mm)
Groove width: 1.3 mm (0.050 in)
Sprocket nose: 9-tooth
Reduced kickback STIHL guide bars 
(with green label)
Bar lengths: 35 cm (14 in.)
Pitch: 3/8" P (9.32 mm)
Groove width: 1.3 mm (0.050 in)
Sprocket nose: 9-toothLow kickback STIHL saw chain (with 
green label)
Picco Micro Mini 3 (61 PMM3) 
Type 3610
Pitch: 3/8" P (9.32 mm)
Drive link gauge: 1.1 mm (0.043 in)
Low kickback STIHL saw chain (with 
green label)
Picco Micro 3 (63 PM3) Type 3636
Picco Super 3 (63 PS3) Type 3616
Picco Duro 3 (63 PD3) Type 3612
Pitch: 3/8" P (9.32 mm)
Drive link gauge: 1.3 mm (0.050 in)
7-tooth for 3/8" P(rim sprocket, spur 
sprocket)
7-tooth for 3/8" P (rim sprocket, spur 
sprocket)
6-tooth for 3/8" P (rim sprocket, spur 
sprocket) 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
60 Please enter your saw model, serial 
number as well as the part numbers of 
the guide bar and saw chain in the 
spaces provided. This will make re-
ordering simpler.
The guide bar and saw chain are subject 
to normal wear and tear. When 
purchasing these parts, always quote 
the saw model, the part numbers and 
names of the parts.
See "Specifications" in this manual for 
the recommended reduced kickback 
cutting attachments.Users of this unit should carry out only 
the maintenance operations described 
in this manual. STIHL recommends that 
other repair work be performed only by 
authorized STIHL servicing dealers 
using genuine STIHL replacement parts.
Genuine STIHL parts can be identified 
by the STIHL part number, the 
{ logo and, in some cases, by 
the STIHL parts symbol K. The 
symbol may appear alone on small 
parts.
For repairs of any component of this 
unit’s air emissions control system, 
please refer to the air emissions 
systems warranty in this manual.Observe all country-specific waste 
disposal rules and regulations.
STIHL products must not be thrown in 
the garbage can. Take the product, 
accessories and packaging to an 
approved disposal site for environment-
friendly recycling.
Contact your STIHL servicing dealer for 
the latest information on waste disposal.
Ordering Spare Parts
Model
Serial number
Guide bar part number
Chain part number
Maintenance and RepairsDisposal
000BA073 KN 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
61 STIHL Incorporated Limited Warranty 
Policy
This product is sold subject to the STIHL 
Incorporated Limited Warranty Policy, 
available at 
http://www.stihlusa.com/warranty.html.
It can also be obtained from your 
authorized STIHL dealer or by calling 
1-800-GO-STIHL (1-800-467-8445).Not for California
Your Warranty Rights and Obligations
The U.S. Environmental Protection 
Agency (EPA) and STIHL Incorporated 
are pleased to explain the Emission 
Control System Warranty on your 
equipment type engine. In the U.S. new 
1997 and later model year small off-road 
equipment engines must be designed, 
built and equipped, at the time of sale, to 
meet the U.S. EPA regulations for small 
non road engines. The equipment 
engine must be free from defects in 
materials and workmanship which 
cause it to fail to conform with U.S. EPA 
standards for the first two years of 
engine use from the date of sale to the 
ultimate purchaser.
STIHL Incorporated must warrant the 
emission control system on your small 
off-road engine for the period of time 
listed below provided there has been no 
abuse, neglect or improper maintenance 
of your small off-road equipment engine.
Your emission control system includes 
parts such as the carburetor and the 
ignition system. Also included may be 
hoses, and connectors and other 
emission-related assemblies.
Where a warrantable condition exists, 
STIHL Incorporated will repair your 
small off-road equipment engine at no 
cost to you, including diagnosis (if the 
diagnostic work is performed at an 
authorized dealer), parts, and labor.Manufacturer's Warranty Coverage
In the U.S., 1997 and later model year 
small off-road equipment engines are 
w a r r a n t e d  f o r  t w o  y e a r s .  I f  a n y  e m i s s i o n -
related part on your engine is defective, 
the part will be repaired or replaced by 
STIHL Incorporated free of charge.
Owner's Warranty Responsibilities
As the small off-road equipment engine 
owner, you are responsible for the 
performance of the required 
maintenance listed in your instruction 
manual. STIHL Incorporated 
recommends that you retain all receipts 
covering maintenance on your small off-
road equipment engine, but STIHL 
Incorporated cannot deny warranty 
solely for the lack of receipts or for your 
failure to ensure the performance of all 
scheduled maintenance.
Any replacement part or service that is 
equivalent in performance and durability 
may be used in non-warranty 
maintenance or repairs, and shall not 
reduce the warranty obligations of the 
engine manufacturer.
As the small off-road equipment engine 
owner, you should be aware, however, 
that STIHL Incorporated may deny you 
warranty coverage if your small off-road 
equipment engine or a part has failed 
due to abuse, neglect, improper 
maintenance or unapproved 
modifications.
You are responsible for presenting your 
small off-road equipment engine to a 
STIHL service center as soon as a 
problem exists. The warranty repairs will 
be completed in a reasonable amount of 
time, not to exceed 30 days.
Limited WarrantySTIHL Incorporated Federal 
Emission Control Warranty 
Statement 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
62 If you have any questions regarding your 
warranty rights and responsibilities, 
please contact a STIHL customer 
service representative at 1-800-467-
8445 or you can write to
STIHL Inc.,
536 Viking Drive, P.O. Box 2015,
Virginia Beach, VA 23450-2015
www.stihlusa.com
Coverage by STIHL Incorporated
STIHL Incorporated warrants to the 
ultimate purchaser and each 
subsequent purchaser that your small 
off-road equipment engine will be 
designed, built and equipped, at the time 
of sale, to meet all applicable emissions 
regulations. STIHL Incorporated also 
warrants to the initial purchaser and 
each subsequent purchaser that your 
engine is free from defects in materials 
and workmanship which cause the 
engine to fail to conform with applicable 
emissions regulations for a period of two 
years.
Warranty Period
The warranty period will begin on the 
date the utility equipment engine is 
purchased by the initial purchaser. 
Product registration is recommended, 
so that STIHL has a means to contact 
you if there ever is a need to 
communicate repair or recall information 
about your product, but it is not required 
in order to obtain warranty service.
If any emission-related part on your 
engine is defective, the part will be 
replaced by STIHL Incorporated at no 
cost to the owner. Any warranted part 
which is not scheduled for replacement 
as required maintenance, or which is scheduled only for regular inspection to 
the effect of "repair or replace as 
necessary" will be warranted for the 
warranty period. Any warranted part 
which is scheduled for replacement as 
required maintenance will be warranted 
for the period of time up to the first 
scheduled replacement point for that 
part.
Diagnosis
You, as the owner, shall not be charged 
for diagnostic labor which leads to the 
determination that a warranted 
emissions part is defective. However, if 
you claim warranty for an emissions 
component and the machine is tested as 
non-defective, STIHL Incorporated will 
charge you for the cost of the emission 
test. Mechanical diagnostic work will be 
performed at an authorized STIHL 
servicing dealer. Emission test may be 
performed either at STIHL Incorporated 
or at any independent test laboratory.
Warranty Work
STIHL Incorporated shall remedy 
warranty defects at any authorized 
STIHL servicing dealer or warranty 
station. Any such work shall be free of 
charge to the owner if it is determined 
that an emissions warranted part is 
defective.
Any manufacturer-approved or 
equivalent replacement part may be 
used for any warranty maintenance or 
repairs on emission-related parts and 
must be provided without charge to the 
owner. STIHL Incorporated is liable for 
damages to other engine components 
caused by the failure of a warranted part 
still under warranty.The following list specifically defines the 
emission-related warranted parts:
–Air Filter
–Carburetor (if applicable)
–Fuel Pump
–Choke (Cold Start Enrichment 
System) (if applicable)
–Control Linkages
–Intake Manifold
–
Magneto or Electronic Ignition 
System (Ignition Module or 
Electronic Control Unit)
–Flywheel
–Spark Plug
–Solenoid Valve (if applicable)
–Injection Valve (if applicable)
–Injection Pump (if applicable)
–Throttle Housing (if applicable)
–Cylinder
–Muffler
–Catalytic Converter (if applicable)
–Fuel Tank
–Fuel Cap
–Fuel Line
–Fuel Line Fittings
–Clamps
–Fasteners
Where to make a Claim for Warranty 
Service
Bring the product to any authorized 
STIHL servicing dealer. 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
63 Maintenance Requirements
The maintenance instructions in this 
manual are based on the application of 
the recommended 2-stroke fuel-oil 
mixture (see also instruction "Fuel"). 
Deviations from this recommendation 
regarding quality and mixing ratio of fuel 
and oil may require shorter maintenance 
intervals.
Limitations
This Emission Control Systems 
Warranty shall not cover any of the 
following:
Nrepair or replacement required 
because of misuse, neglect or lack 
of required maintenance,
Nrepairs improperly performed or 
replacements not conforming to 
STIHL Incorporated specifications 
that adversely affect performance 
and/or durability, and alterations or 
modifications not recommended or 
approved in writing by STIHL 
Incorporated,
and
Nreplacement of parts and other 
services and adjustments 
necessary for required maintenance 
at and after the first scheduled 
replacement point.
For California only
Your Warranty Rights and Obligations
The California Air Resources Board 
(CARB) and STIHL Incorporated are 
pleased to explain the emission control 
system warranty on your 2017 and later 
small off-road equipment engine.
In California, new equipment that uses 
small off-road engines must be 
designed, built, and equipped to meet 
the State's stringent anti-smog 
standards. STIHL Incorporated must 
warrant the emissions control system on 
your small off-road engine for the period 
listed below provided there has been no 
abuse, neglect or improper maintenance 
of your small off-road engine.
Your emission control system may 
include parts such as the carburetor or 
fuel-injection system, the ignition 
system, and catalytic converter. Also 
included may be hoses, belts, 
connectors or other emission-related 
assemblies.
Where a warrantable condition exists, 
STIHL Incorporated will repair your 
small off-road equipment engine at no 
cost to you including diagnosis, parts 
and labor.Manufacturer’s Warranty 
Responsibilities
This emissions control system is 
warranted for two years in California. If 
any emissions-related part on your 
equipment is defective, the part will be 
repaired or replaced by STIHL 
Incorporated free of charge.
Owner’s Warranty Responsibilities
As the small off-road equipment engine 
owner, you are responsible for 
performance of the required 
maintenance listed in your instruction 
manual. STIHL Incorporated 
recommends that you retain all receipts 
covering maintenance on your small off-
road equipment engine, but STIHL 
Incorporated cannot deny warranty 
solely for the lack of receipts or your 
failure to ensure the performance of all 
scheduled maintenance.
As the small off-road equipment engine 
owner, you should however be aware 
that STIHL Incorporated may deny you 
warranty coverage if your small off-road 
equipment engine or a part has failed 
due to abuse, neglect, or improper 
maintenance or unapproved 
modifications.
You are responsible for presenting your 
small off-road equipment engine to a 
STIHL servicing dealer as soon as the 
problem exists. The warranty repairs 
should be completed in a reasonable 
amount of time, not to exceed 30 days. If 
you have any questions regarding your 
warranty rights and responsibilities, 
please contact a STIHL customer 
service representative at 1-800-467-
8445 or you can write to
STIHL Incorporated 
California Exhaust and 
Evaporative Emissions 
Control Warranty Statement 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
64 STIHL Inc., 536 Viking Drive,
P.O. Box 2015,
Virginia Beach, VA 23450-2015.
www.stihlusa.com
Coverage by STIHL Incorporated
STIHL Incorporated warrants to the 
ultimate purchaser and each 
subsequent purchaser that your small 
off-road equipment engine is designed, 
built and equipped, at the time of sale, to 
meet all applicable emission 
regulations.
STIHL Incorporated also warrants to the 
initial purchaser and each subsequent 
purchaser that your engine is free from 
defects in materials and workmanship 
which cause the engine to fail to conform 
to applicable emission regulations for a 
period of two years.
Defects Warranty Period
The warranty periods will begin on the 
date the utility equipment engine is 
purchased by the initial purchaser. If any 
emission-related part on your engine is 
defective, the part will be replaced by 
STIHL Incorporated at no cost to the 
owner.
Add-on or modified parts that are not 
exempted by CARB may not be used. 
The use of any non-exempted add-on or 
modified parts will be grounds for 
disallowing a warranty claim. STIHL 
Incorporated will not be liable to warrant 
failures of warranted parts caused by the 
use of a non-exempted add-on or 
modified part.The warranty on emissions-related parts 
will be interpreted as follows:
1.Any warranted part that is not 
scheduled for replacement as 
required maintenance in the written 
instructions required in the 
Emission Warranty Parts List (see 
below) must be warranted for the 
warranty period defined in 
Subsection COVERAGE BY STIHL 
INCORPORATED, see above. If 
any such part fails during the period 
of warranty coverage, it must be 
repaired or replaced by the 
manufacturer according to 
Subsection (4) below. Any such part 
repaired or replaced under the 
warranty must be warranted for the 
remaining warranty period.
2.Any warranted part that is 
scheduled only for regular 
inspection in the written instructions 
required by the Emission Warranty 
Parts List (see below) must be 
warranted for the warranty period 
defined in Subsection COVERAGE 
BY STIHL INCORPORATED, see 
above. A statement in such written 
instructions to the effect of "repair or 
replace as necessary" will not 
reduce the period of warranty 
coverage. Any such part repaired or 
replaced under warranty must be 
warranted for the remaining 
warranty period.
3.Any warranted part that is 
scheduled for replacement as 
required maintenance in the written 
instructions required by the 
Emission Warranty Parts List (see 
below) must be warranted for the 
period of time prior to the first 
scheduled replacement point for that part. If the part fails prior to the 
first scheduled replacement, the 
part must be repaired or replaced by 
the engine manufacturer according 
to Subsection (4) below. Any such 
part repaired or replaced under 
warranty must be warranted for the 
remainder of the period prior to the 
first scheduled replacement point 
for the part.
4.Repair or replacement of any 
warranted part under the warranty 
must be performed at a warranty 
station at no charge to the owner.
5.Notwithstanding the provisions of 
Subsection (4) above, warranty 
services or repairs will be provided 
at all manufacturer distribution 
centers that are authorized to 
service the subject engines.
6.The owner must not be charged for 
diagnostic labor that leads to the 
determination that a warranted part 
is in fact defective, provided that 
such diagnostic work is performed 
at a warranty station.
Warranty Work
STIHL Incorporated shall remedy 
warranty defects at any authorized 
STIHL servicing dealer or warranty 
station. Any such work shall be free of 
charge to the owner if it is determined 
that a warranted part is defective. Any 
manufacturer approved or equivalent 
replacement part may be used for any 
warranty maintenance or repairs on 
emission-related parts and must be 
provided without charge to the owner. 
STIHL Incorporated is liable for  
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
65 damages to other engine components 
caused by the failure of a warranted part 
still under warranty.
Emission Warranty Parts List
Air Filter, Carburetor (if applicable), Fuel 
Pump, Choke (Cold Start Enrichment 
System) (if applicable), Control 
Linkages, Intake Manifold, Magneto or 
Electronic Ignition System (Ignition 
Module or Electronic Control Unit), Fly 
Wheel, Spark Plug, Solenoid Valve (if 
applicable), Injection Valve (if 
applicable), Injection Pump (if 
applicable), Throttle Housing (if 
applicable), Cylinder, Muffler, Catalytic 
Converter (if applicable), Fuel Tank, 
Fuel Cap, Fuel Line, Fuel Line Fittings, 
Clamps, Fasteners.
Where to make a Claim for Warranty 
Service
Bring the STIHL product to any 
authorized STIHL servicing dealer.
Limitations
The repair or replacement of any 
warranted part otherwise eligible for 
warranty coverage may be excluded 
from such warranty coverage if STIHL 
Incorporated demonstrates that the 
STIHL product has been abused, 
neglected, or improperly maintained, 
and that such abuse, neglect, or 
improper maintenance was the direct 
cause of the need for repair or 
replacement of the part. That 
notwithstanding, any adjustment of a 
component that has a factory installed, 
and properly operating, adjustment 
limiting device is still eligible for warranty 
coverage.
STIHL Registered Trademarks
STIHL
®
{
K
The color combination orange-grey 
(U.S. Registrations #2,821,860; 
#3,010,057, #3,010,058, #3,400,477; 
and #3,400,476)
AutoCut
®
FARM BOSS®
iCademy®
MAGNUM®
MasterWrench Service®
MotoMix®
OILOMATIC®
Rock Boss®
STIHL Cutquik®
STIHL DUROMATIC®
STIHL Quickstop®
STIHL ROLLOMATIC®
STIHL WOOD BOSS®
TIMBERSPORTS®
WOOD BOSS®
YARD BOSS®
Some of STIHL’s Common Law 
Trademarks
4-MIX ™
BioPlus ™
Easy2Start ™
EasySpool ™
ElastoStart ™
Ematic ™
FixCut ™
IntelliCarb ™
Master Control Lever ™
Micro ™
Pro Mark ™
Quiet Line ™
STIHL M-Tronic ™
Trademarks
TMSTIHLInjection 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
English
66 STIHL OUTFITTERS ™
STIHL PICCO ™
STIHL PolyCut ™
STIHL PowerSweep ™
STIHL Precision Series ™
STIHL RAPID ™
STIHL SuperCut ™
TapAction ™
TrimCut ™
This listing of trademarks is subject to 
change.
Any unauthorized use of these 
trademarks without the express written 
consent of 
ANDREAS STIHL AG & Co. KG, 
Waiblingen is strictly prohibited. 
						

							Manual de instrucciones original Impreso en papel libre de cloro.
Las tintas contienen aceites vegetales, el papel es reciclable. © ANDREAS STIHL AG & Co. KG, 2017
0458-533-8621-D. VA3.G17. 
0000000877_028_EA
MS 171, MS 181, MS 181 C, MS 211, MS 211 C
español / EE.UU
67
{Este manual de instrucciones está protegido por derechos de propiedad intelectual. Todos los derechos reservados, especial-
mente los derechos de reproducción, traducción y procesamiento con sistemas electrónicos.
Contenido
Permita que solamente las personas 
que comprenden la materia tratada en 
este manual manejen su motosierra.
Para obtener el rendimiento y 
satisfacción máximos de la motosierra 
STIHL, es importante que lea, 
comprenda y respete las medidas de 
seguridad y las instrucciones de uso y 
mantenimiento dadas en el capítulo 
"Medidas de seguridad y técnicas de 
uso", antes de usar su motosierra. Para 
obtener información adicional, visite 
www.stihlusa.com.
Comuníquese con su representante de 
STIHL o el distribuidor de STIHL para su 
zona si no se entiende alguna de las 
instrucciones dadas en el presente 
manual.
ADVERTENCIA
Dado que la motosierra es una 
herramienta para cortar madera que 
funciona a gran velocidad, es necesario 
tomar medidas especiales de seguridad 
igual que con cualquier sierra 
motorizada, para reducir el riesgo de 
lesiones. El uso descuidado o 
inadecuado puede causar lesiones 
graves e incluso mortales. Acerca de este manual de 
instrucciones 68
Medidas de seguridad y técnicas 
de manejo 69
Accesorio de corte 95
Montaje de la espada y cadena 
(tensor lateral de la cadena) 96
Montaje de la espada y cadena 
(tensor rápido de la cadena) 97
Tensado de la cadena de aserrado 
(tensor lateral de la cadena) 99
Tensado de la cadena de aserrado 
(tensor rápido de la cadena) 99
Revisión de tensión de la cadena 99
Combustible 100
Llenado de combustible 101
Lubricante de cadena 105
Llenado del tanque de aceite de la 
cadena 105
Revisión de lubricación de la 
cadena 106
Freno de la cadena 106
Manejo durante el invierno 107
Arranque / parada del motor 108
Instrucciones para el uso 112
Cuidado de la espada 113
Cubierta 114
Sistema de filtro de aire 114
Limpieza del filtro de aire 115
Gestión del motor 115
Ajuste del carburador 116
Chispero en el silenciador 117
Bujía 117Funcionamiento del motor 119
Almacenamiento de la máquina 119
Revisión y sustitución del piñón de 
cadena 119
Mantenimiento y afilado de la 
cadena de aserrado 120
Información para mantenimiento 125
Componentes importantes 127
Especificaciones 129
Pedido de piezas de repuesto 131
Información de reparación 131
Desecho 132
Garantía limitada 132
Declaración de garantía de STIHL 
Incorporated sobre sistemas de 
control de emisiones según normas 
Federales 132
Declaración de garantía de STIHL 
Incorporated sobre el control de 
emisiones de gases de escape y 
emisiones por evaporación para el 
Estado de California 135
Marcas comerciales 138 
						

							MS 171, MS 181, MS 181 C, MS 211, MS 211 C
español / EE.UU
68 Este Manual de instrucciones 
corresponde a una motosierra STIHL, 
que aquí también está representada por 
el término "máquina".
Pictogramas
Todos los pictogramas que se 
encuentran fijados o grabados en la 
máquina se explican en este manual.
Según el modelo, los pictogramas 
siguientes pueden aparecer en su 
máquina.
Símbolos en el texto
Muchas de las instrucciones de uso y 
seguridad vienen acompañadas de 
ilustraciones.
Los pasos individuales o 
procedimientos descritos en el manual 
pueden estar señalados en diferentes 
maneras:
NSe usa un punto para denotar un 
paso o procedimiento.
Una descripción de un paso o 
procedimiento que se refiere 
directamente a una ilustración puede 
contener números de referencia que 
aparecen en la ilustración. Ejemplo:
NSuelte el tornillo (1).
NPalanca (2) ...Además de las instrucciones de uso, en 
este manual pueden encontrarse 
párrafos a los que usted debe prestar 
atención especial. Tales párrafos están 
marcados con los símbolos y las 
palabras identificadoras que se 
describen a continuación.
PELIGRO
Identifica una situación de peligro que, 
de no evitarse, causará lesiones graves 
o mortales.
ADVERTENCIA
Identifica una situación de peligro que, 
de no evitarse, podría causar lesiones 
graves o mortales.
INDICACIÓN
Indica el riesgo de daños a la propiedad, 
incluidos la máquina o sus 
componentes.
Mejoramientos técnicos
La filosofía de STIHL es mejorar 
continuamente todos sus productos. 
Como resultado de ello, periódicamente 
se introducen cambios de diseño y 
mejoras. Por lo tanto, es posible que 
algunos cambios, modificaciones y 
mejoras no se describen en este 
manual. Si las características de 
funcionamiento o la apariencia de su 
máquina difieren de las descritas en 
este manual, comuníquese con el 
concesionario STIHL para obtener la 
ayuda que requiera.
Acerca de este manual de 
instrucciones
Tanque de combustible; 
mezcla de gasolina y 
aceite de motor
Depósito de aceite de 
cadena; aceite de 
cadena
Aplicación y soltado del 
freno de la cadena STIHL 
Quickstop
Sentido de rotación de la 
cadena
Ematic; control de canti-
dad de aceite de cadena
Tensión de la cadena
Precalentamiento del aire 
de admisión para funcio-
namiento en invierno
Aire de admisión para 
funcionamiento en 
verano
Calentador de manillar
Uso de válvula de 
descompresión
Uso de bomba manual de 
combustible