Steinberg UR824 Operation Manual

Panel Controls for the Software Programs
UR824  Operation Manual21
From the dspMixFx UR824
Click “REV-X Edit” (page 11 ) in the section “Master 
Area.”
Panel Controls
NOTE
This section uses the Hall type of REV-X as an 
example.
 Reverb Time
Adjusts the reverb time.  This parameter links to 
Room Size. The adjustable range varies 
depending on the REV-X type.
 Initial Delay
Adjusts the time that elapses between the direct, 
original sound and the init ial reflections that follow 
it.
Range:  0.1 msec –...

Panel Controls for the Software Programs
UR824  Operation Manual22
MIX (VST Plug-in version only)
Adjusts the output level balance between the 
original sound and effect sound.
Range:  0% – 100%
 Time Axis Setting
Select the display range of the time (horizontal 
axis) on the graph.
Display range:  500 msec – 50 sec
? Zoom Out
Zooms out the display range of the time 
(horizontal axis) on the graph.
 Zoom In
Zooms in the display range of the time (horizontal 
axis) on the graph.
TIPS
• You can reset...

Usage Examples
UR824  Operation Manual23
Usage Examples
Introduction
This section introduces some usage examples of 
the device. It is assumed that the audio driver 
settings on the DAW software have been properly 
configured according to the “Basic Operation” 
section in the included Getting Started manual. If 
you have not configured them yet, refer to the 
section “Basic Operation” to complete the 
configuration.
Recording with the Channel 
Strip and REV-X
This section shows how to record a vocal to...

Usage Examples
UR824  Operation Manual24
8.Click “Record” to start the recording.
9.After finishing the recording, click “Stop” to 
stop it.
10.Turn “Monitor” off (dark) for the audio track.
11.Click the Ruler to move the project cursor to 
the desired point for starting playback.
12.Click “Play” to check the recorded sound.
When listening to the sound over monitor 
speakers, adjust the output signal level by the 
OUTPUT LEVEL knob on the device. 
Operation is now completed.
Programs Other Than Cubase...

Usage Examples
UR824  Operation Manual25
Operation
1.
Connect the optical output terminal (ADAT) 
of the mic preamp to the OPTICAL A IN on 
the device.
2.Connect the WCLK OUT on the device to the 
word clock input terminal on the mic 
preamp.
3.Switch the clock source in the device to 
“Internal” by using the following window.
Windows
“(device name) Window” (page 7) in the 
section “Control Panel of the Audio Driver.”
Mac
Audio MIDI Setup
4.Switch the clock source of the mic preamp 
to the word clock...

Appendix
UR824  Operation Manual26
Appendix
Glossary
MIX
MIX refers to the stereo output signals which flow in 
the device. The input signals to the device flow to 
each MIX. You can assign any MIX to any analog 
output jack or any digital output jack.
VST Plug-in
VST (Virtual Studio Technology) is a technology 
developed by Steinberg which allows the integration 
of virtual effect processors and instruments into your 
digital audio environment. VST Plug-ins are 
instrument- and effect-based software of...

Appendix
UR824  Operation Manual27
Contents of the Getting 
Started Section
PRECAUTIONS
Introduction
A Message from the Development Team
Included Accessories
How to Read the Manual
Panel Controls and Terminals
Rear Panel
Front Panel
Setup
1. Setting up the Power Supply
2. Installing Cubase AI
3. Installing TOOLS for UR824
4. Downloading the Li censes (Activation)
Basic Operations
Introduction
Connection Example
Configuring Audio Driver Settings on 
the DAW Software
Troubleshooting
Appendix
Contents of...

Appendix
UR824  Operation Manual28
Signal Flow
The following chart indicates the signal flow in the device.
NOTE
• The controllers on the device, such as the HI-Z switch, INPUT GAIN knob, and OUTPUT LEVEL knob, are not 
included in this chart.
• To configure each parameter, use the “dspMixFx UR824” (p age 8) or “Dedicated Windows for Cubase Series” 
(page 14).
• Some parts of the following signal flow may differ depending on the routing settings in the device.
MIX 4
MIX 3
MIX 2
Ch. Strip
(MON.FX)
MIX 1...

Appendix
UR824  Operation Manual29
*1The following chart indicates the Ch.Strip (Channel Strip) insertion location.
You can apply eight Channel Strips to mono channels, or four Channel Strips to a stereo channel.
*2 One of the MIX 1–4 signals can be sent to the REV-X.
*3 The built-in REV-X is equipped with an “FX Bus” which is used for sending the signal from DAW software to 
the REV-X. For example, to send the recorded audio data to the REV-X, you can check the sound with the 
REV-X, which is used for...

Appendix
UR824  Operation Manual30
Block Diagrams
UR824 – 44.1/48 kHz
8 Analog In/Out, 16 Digital In/Out, 26 DAW In/24 DAW Out 8+2 BUS 
:Ÿ:˜
:¤: :š:†:£: :¥:œ:w: :¥:§:¬:«
:ž:˜: :¥
:¤:¬:«:œ
:£:œ:­:œ:£
:²:„:Š:‹:»:™:ÌC>:‚:ˆ:‡:»:™:Ì:´ 
:˜:›:˜:«:†:¦:§:«: :š:˜:£:w: :¥:§:¬:«
: :¥:§:¬:«:w:™

/64

5KI2GCM/64
:§:˜:¥
:¤:¬:«:œ :£:œ:­:œ:£
:™:˜:£
/64
/64
:©:œ:­:œ:©:™:w:£
:©:œ:­:œ:©:™:w:©
:£:œ:­:œ:£:…:…:…:…:…:…
:©:¼:Í:¯
:©:œ:­:œ:©:™:w:£
:©:œ:­:œ:©:™:w:©
:Ê:¸:Ä:¼:w:¸:Ê:w:¸:¹:Æ:Í:¼
:©:œ:­
:Ê:¸:Ä:¼:w:¸:Ê:w:¸:¹:Æ:Í:¼...