Steinberg UR824 Operation Manual

EN
DE
FR
ES
JA
USB AUDIO INTERFACE
IT 

UR824  Operation Manual2
Contents
Introduction.................. ..........................................3
Contents in this Operation Manu al............................... 3
Features .............. ............................................ ............. 3
Panel Controls and Term inals (Details)...............4
Rear Panel....................................................... ............. 4
Front Panel ......................................................... .......... 5
Panel Controls for the...

Introduction
UR824  Operation Manual3
Introduction
Contents in this Operation 
Manual
This Operation Manual explains how to use the 
device. The explanations in this manual assume that 
you’ve set up the device and prepared it for use 
according to the included Getting Started 
document. If you haven’t done that yet, refer to the 
Getting Started document and complete the setup 
before reading this manual.
Features
High-resolution Microphone 
Preamplifiers (D-Pre) 
Discrete microphone preamps featuring a...

Panel Controls and Terminals (Details)
UR824  Operation Manual4
Panel Controls and 
Terminals (Details)
Rear Panel
DC IN 16V
For connection to the AC power adaptor.
 Grounding screw
For connection to a ground wire.
If you have a problem with hum or noise, use this 
terminal to connect to ground. The noise may be 
reduced.
 USB2.0 (USB port)
For connection to a computer.
 WCLK switch
Switches between IN and OUT for the upper 
WCLK terminal.
 WCLK IN (OUT)/OUT (BNC connector)
For connection to the...

Panel Controls and Terminals (Details)
UR824  Operation Manual5
Front Panel
MIC/LINE/HI-Z (XLR/phone type, 
balanced/unbalanced)
For connection to a microphone, digital 
instrument, electric guitar, or electric bass.
 HI-Z switch
Turns on (0 ) and off (/) the HI-Z of the MIC/
LINE/HI-Z.
Turn this switch on when connecting high 
impedance instruments, such as an electric 
guitar or electric bass, directly to the MIC/LINE/
HI-Z.
When you turn this switch on, use an unbalanced 
phone type cable for...

Panel Controls and Terminals (Details)
UR824  Operation Manual6
• Do not connect or disconnect a device while 
phantom power is applied. Doing so can damage the 
connected device and/or  the unit itself.
• To protect your speaker system, leave the monitor  speakers turned off when switching the phantom 
power on/off. It’s also a good idea to turn all output 
volume controls down to their minimum. Neglect of 
these precautions may result in large noise bursts 
that may damage your equipment, your ears, or...

Panel Controls for the Software Programs
UR824  Operation Manual7
Panel Controls for the 
Software Programs
Control Panel of the Audio 
Driver
This is the control panel for selecting the general 
settings of the audio driver. Click the upper tabs to 
select the desired window.
Screenshot
How to Open the Window
Windows
•[Start]  [Control Panel]   [Hardware and Sound] 
or [Sounds, Speech, and Audio Devices]   
[Yamaha Steinberg USB Driver]
• From the Cubase series menu, [Devices]   [Device Setup]  ...

Panel Controls for the Software Programs
UR824  Operation Manual8
Enable Power Management
Select enable (checkmark) and disable (no 
checkmark) for automatic power off.
The device is equipped with an automatic power 
off function. When this function is enabled, the 
power of the device will turn off automatically 
(after thirty minutes) when one of the following 
actions is performed. The power button will flash 
during the thirty-minute interval.
• Turning off the computer.
• Disconnecting the USB...

Panel Controls for the Software Programs
UR824  Operation Manual9
How to Open the Window
Windows
[Start]  [All Programs]   [Steinberg UR824]   
[dspMixFx UR824]
Mac
[Macintosh HD]   [Applications]   [dspMixFx 
UR824]
Panel Controls
To o l  A r e a
This is the area for configuring the common settings 
of the dspMixFx UR824.
 Quit
Quits the dspMixFx UR824.
 Minimize
Minimizes the dspMixFx UR824 window.
 Menu
Provides four menus, including Save the settings 
file of the dspMixFx UR824 (page 26) and...

Panel Controls for the Software Programs
UR824  Operation Manual10
Channel Area
This is the area for configuring the input channel 
settings.
Channel Link
Turns on (lit) and off (dark) the channel link of two 
adjacent channels. When you turn this on, two 
mono channels will become one stereo  channel.
 Level Meter
Indicates the signal level.
 High Pass Filter
Turns on (lit) and off (dark) the high pass filter.
To select the cutoff frequency of the high pass 
filter, use the “Setup Window” (page 12)...