Steinberg Nuendo 3 Remote Control Devices Manual

NUENDO
Radikal Technologies SAC-2K 8 – 31
Dynamics button: Selected Channel mode Routing:
•Page 1 - Output Bus, Monitor, Input Bus, Input Gain, Input Phase
•Pressing a V-Pot will toggle Monitor.
For a description of the functionalities for the MIDI button: Selected 
Channel mode Inserts, Shift+Inserts/Sends button: Global mode 
Send Effects, Shift+Dynamics button: Global mode Master Effects, 
Shift+MIDI button: Global mode Instruments, see the separate pdf 
document “Mackie Control and Nuendo”. 

NUENDO
8 – 32 Radikal Technologies SAC-2K 

9
Roland MCR-8 

NUENDO
9 – 34 Roland MCR-8
Specifications
Before you can initiate remote control operation, the MCR-8 “Mode” 
switch must be set to “4”.
The Roland MCR-8 can control 16 mixer channels, plus transport con-
trol. The “A/B switch” is used to switch between controlling channels 
1 - 8 and 9 - 16. The following MCR-8 parameters control the equiva-
lent parameters for each channel strip:
•Fader level, mute, solo and pan.
The following MCR-8 transport controls control the equivalent Nuendo 
functions:
•Play,...

10
Tascam US-428 

NUENDO
10 – 36 Tascam US-428
Specifications
The US-428 can remote control up to 64 mixer channels and 1 or 2 
DSP Factory cards, if installed (Windows version only). 
•When the Tascam US-428 device is added in the Device Setup dia-
log, you can open the Remote Status window by selecting “Tascam 
US-428” from the Devices menu.
This indicates which bank (group of eight channels in Nuendo) is currently being con-
trolled by the remote device. To select another bank, use the pop-up menu in the win-
dow or...

NUENDO
Tascam US-428 10 – 37
Nuendo mixer
The following US-428 controls will remote control the following mixer 
parameter for each channel strip:
•Fader: volume
•Mute/Solo: mute and solo (selected via the Solo switch)
•Select: selects channel for editing
•Pan-Dial: pan
•EQ-Gain
Controls the EQ gain for each band selected with the Low, LoMid, HiMid and High but-
tons. These correspond to the four EQ bands in Nuendo, starting from the leftmost band.
•EQ-Freq
Controls the EQ frequency for each band...

NUENDO
10 – 38 Tascam US-428
DSP Factory (Nuendo for Windows only)
The following US-428 controls will remote control the following DSP 
Factory parameter for each channel strip:
•Fader: volume
•Mute/Solo: mute and solo (selected via the Solo switch)
•Select: selects channel for editing
•Pan-Dial: pan
•EQ-Gain
Controls the corresponding EQ gain for each band selected with the Low, LoMid, 
HiMid and High buttons.
•EQ-Freq
Controls the corresponding EQ frequency for each band selected with the Low, LoMid,...

11
Yamaha 01V 

NUENDO
11 – 40 Yamaha 01V
Specifications
The Yamaha 01V can remote control either the Nuendo mixer or the 
Yamaha DSP Factory if installed (Windows only; see the separate 
“Using Nuendo with DSP Factory” document for details). Before you 
can initiate remote control operation, the 01V must be set up in the 
following way:
•MIDI Parameter Change and Receive must be enabled.
•MIDI Control Change and Receive must be disabled.
•Device ID / MIDI Channel Receive must be set to “1”.
•Local Control should be set...