Steinberg Cubase SX/SL 3 Remote Control Devices Manual

CUBASE SX/SLRadikal Technologies SAC-2K 8 – 31
•The Play, Stop, Record, "" transport controls control the 
equivalent functions in Cubase SX/SL.
•The jog wheel is used to move the project cursor position in Cubase 
SX/SL.
•The Scrub button is currently not supported.
•The status of the Num button (in the Software Navigation section) de-
termines the assignment of the "1" to "0" and Enter buttons:
With Num-LED on, use the buttons to set the project cursor position:
• Immediately...

CUBASE SX/SL8 – 32 Radikal Technologies SAC-2K
Pan button in the Mixer-Mode section: Fader Set mode Panning:
• Page 1 - Pan left/right
• Page 2 - Pan front/rear
• Pressing a V-Pot will toggle Monitor for that channel.
High button: Fader Set mode EQ High:
• Page 1 - Gain
• Page 2 - Frequency 
• Page 3 - Q
• Page 4 - Enable
• Pressing a V-Pot will bypass EQs for that channel.
HiMid, LowMid, Low button: Fader Set mode EQ Mid-High, Mid-Low, 
Low (same functionality as above).
Snd/Ins 1 button: Fader Set mode...

CUBASE SX/SLRadikal Technologies SAC-2K 8 – 33
Dynamics button: Selected Channel mode Routing:
• Page 1 - Output Bus, Monitor, Input Bus, Input Gain, Input Phase
• Pressing a V-Pot will toggle Monitor.
For a description of the functionalities for the MIDI button: Selected 
Channel mode Inserts, Shift+Inserts/Sends button: Global mode 
Send Effects, Shift+Dynamics button: Global mode Master Effects, 
Shift+MIDI button: Global mode Instruments, see the separate pdf 
document “Mackie Control and Cubase...

CUBASE SX/SL8 – 34 Radikal Technologies SAC-2K 

9
Roland MCR-8 

CUBASE SX/SL9 – 36 Roland MCR-8
Specifications
Before you can initiate remote control operation, the MCR-8 “Mode” 
switch must be set to “4”.
The Roland MCR-8 can control 16 mixer channels, plus transport 
control. The “A/B switch” is used to switch between controlling chan-
nels 1 - 8 and 9 - 16. The following MCR-8 parameters control the 
equivalent parameters for each channel strip:
•Fader level, mute, solo and pan.
The following MCR-8 transport controls control the equivalent Cubase 
SX/SL...

10
Tascam US-428 

CUBASE SX/SL10 – 38 Tascam US-428
Specifications
The US-428 can remote control up to 64 mixer channels and 1 or 2 
DSP Factory cards, if installed (Windows version only). 
•When the Tascam US-428 device is added in the Device Setup dia-
log, you can open the Remote Status window by selecting “Tascam 
US-428” from the Devices menu.
This indicates which bank (group of eight channels in Cubase SX/SL) is currently be-
ing controlled by the remote device. To select another bank, use the pop-up menu in 
the...

CUBASE SX/SLTascam US-428 10 – 39
Cubase SX/SL mixer
The following US-428 controls will remote control the following mixer 
parameter for each channel strip:
•Fader: volume
•Mute/Solo: mute and solo (selected via the Solo switch)
•Select: selects channel for editing
•Pan-Dial: pan
•EQ-Gain
Controls the EQ gain for each band selected with the Low, LoMid, HiMid and High 
buttons. These correspond to the four EQ bands in Cubase SX/SL, starting from the 
leftmost band.
•EQ-Freq
Controls the EQ frequency for...

CUBASE SX/SL10 – 40 Tascam US-428
DSP Factory (Cubase SX/SL for Windows only)
The following US-428 controls will remote control the following DSP 
Factory parameter for each channel strip:
•Fader: volume
•Mute/Solo: mute and solo (selected via the Solo switch)
•Select: selects channel for editing
•Pan-Dial: pan
•EQ-Gain
Controls the corresponding EQ gain for each band selected with the Low, LoMid, 
HiMid and High buttons.
•EQ-Freq
Controls the corresponding EQ frequency for each band selected with the...