Starplus Triad Xts Installation Manual

							2
System Specifications
This chapter describes the hardware used by theXTSsystem and lists the specifications
for each component. 
						

							» » » » » » »  NOTES   » » » » » » » 
						

							System Capacities2-3
Chapter 2 - System Specifications
System Capacities
The following tables and charts describe system capacities and display the configuration
flexibility of the system.
The KSU contains a PSU slot, nine universal slots, one MPB slot, one LMU slot, one RAU slot, and
PFTU and RGU connectors.
Table 2-1: System Capacity
DescriptionUniversal
SlotsUsable Capacity
MPB2 MPB1
Time Slots*Cabinet 0 9 136 Time Slots 136 Time Slots
Cabinet 1 9 96-144 Time Slots** N/A
Cabinet 2 9 96-144 Time Slots** N/A
KSU Cabinets 3 Cabinets 1 Cabinet
Serial Ports (RS-232C) 4 Ports
(MPB: 2, MISB: 2)3Ports
(MPB:1, MISB:2)
Alarm 3 Inputs
(RAU: 2, MISB: 1)3 Inputs
(RAU: 2, MISB: 1)
External Control Contacts 7 Contacts
(RAU: 3, MISB: 4)7Contacts
(RAU: 3, MISB: 4)
Music Source Inputs 3 Inputs
(MPB: 1, MISB: 2)2Inputs
(MPB: 0, MISB: 2)
DTMF Receivers 24 Receivers
(MPB:4,SLT/COcards:20)24 Receivers
(MPB:0,SLT/COcards:24)
Power Fail Circuits 30 Circuits 30 Circuits
Paging ZonesExternal 3 Zones
(MPB: 1, MISB: 2)2 Zones
(MPB: 0, MISB: 2)
Internal 8 Zones 8 Zones
DSS/BLF Consoles 3 Consoles (per station) 3 Consoles (per station)
Ethernet Connection 1 N/A
* Time slots are used to support each CO Line and each station. A Cabinet cannot support more than 96 stations.
** Maximum time slots on Cabinet 1 and Cabinet 2 can range from 96 to 144 each, but the total time slots between the
two Cabinets cannot exceed 240.
*** MPB1 - Maximum COs are 48 and maximum stations are 96
MPB2 - Maximum COs are 144 and maximum stations are 252 
						

							2-4System Components
Chapter 2 - System Specifications
System Components
This table shows the slot positions for each card that can be installed in theXTSSystem.
Table 2-2: System Card Description
Part
NumberBoardNumber of
Time SlotsSlot
PositionDescription
8031-41 BRIB 8 1-7 or 0-7 Basic Rate Interface Board
8031-10 DIDB 4 1-8 or 0-8 Direct Inward Dial Board
8032-30 DTIB12 12 0-8 Digital Telephone Interface Board
8032-40 DTIB24 24 0-8 Digital Terlephone Interface Board
8031-50 DTRU --- LCOB, SLIB, DIDB DTMF Receiver Unit (2 port)
3031-60 DTRU4 --- LCOBE, LCOBC,
SLIBE, SLIBC,
T1IB, PRIB, BRIBDTMF Receiver Unit (4 port)
8032-20 ETIB 12 1-8 or 0-8 Electronic Telephone Interface Board
3000-00 KSU --- --- Key Service Unit
8031-00 LCOB 6 1-8 or 0-8 Loop Start CO Interface Board
3031-02 LCOBE 8 1-8 or 0-8 Loop Start CO Interface Board (01, 3Q)
3031-03 LCOBC 8 1-7 or 0-7 Loop Start CO Interface (01, 3Q) with Caller ID
3035-01 LMU1 --- LMU Link Module Unit (Cabinet 0 only)
3035-02 LMU2 --- LMU Link Module Unit (Cabinets 1 & 2 only)
8035-00 MISB --- 8 only Miscellaneous Board (Cabinet 0 only)
3030-30 MODU --- MPB 19.2 Kbps Internal Modem
3030-01 MPB1 --- MPB Main Processing Board = 136 Time Slots Usable
3030-03 MPB2 --- MPB Main Processing Board = 376 Time Slots Usable
8033-10 MSGU --- SLIB Message Waiting Unit
3033-10 MSGU48 --- SLIBE, SLIBC Message Waiting Unit
8036-00 PFTU --- --- Power Failure Transfer Unit
The first range, for entries that show two ranges of slot positions, applies to Cabinet 0. For example, the LCOBC card can be
used in slot 1-7 of Cabinet 0 and in slots 0-7 in either Cabinet 1 or Cabinet 2. 
						

							System Components2-5
Chapter 2 - System Specifications
Part Num-
berBoardNumber of
Time SlotsSlot
PositionDescription
3030-10 PMU --- MPB1 Program Module Unit, 4 MB ROM
3030-20 PMU --- MPB2 Program Module Unit, 8 MB ROM
8031-40 PRIB 24 1-7 or 0-7 Primary Rate Interface Board
3071-10 PSU --- PSU Power Supply Unit, 350W
3035-03 RAU --- RAU Relay Alarm Unit (used only in Cabinet 0)
3073-00 RGU3 --- --- Ring Generator Unit (25Hz) : Sine Wave, Internal
8035-10 SIU --- MISB Serial Interface Unit
8033-00 SLIB 6 1-8 or 0-8 Single Line Interface Board
3033-03 SLIBC 12 1-7 or 0-7 Single Line Interface Board with Caller ID
3033-02 SLIBE 12 1-8 or 0-8 Single Line Interface Board
8031-31 T1IB 24 1-7 or 0-7 T1 Interface Board
TR8037-02 VOIP 8 1-7 or 0-7
DiscoveryVoIP Card w/one VoIP Module
TR8037-04 VOIP 8 1-7 or 0-7
DiscoveryVoIP Card w/two VoIP Modules
TR8037-06 VOIP 8 1-7 or 0-7
DiscoveryVoIP Card w/three VoIP Modules
TR8037-08 VOIP 8 1-7 or 0-7
DiscoveryVoIP Card w/four VoIP Modules
TR8037-10 Module 2 VOIP
DiscoveryVoIP module only (for upgrade)
The first range, for entries that show two ranges of slot positions, applies to Cabinet 0. For example, the T1IB card can be
used in slot 1-7 of Cabinet 0 and in slots 0-7 in either Cabinet 1 or Cabinet 2.
Table 2-2: System Card Description 
						

							2-6System Configuration Tables
Chapter 2 - System Specifications
System Configuration Tables
Table 2-3: System Capacity
ItemCapacity
Account Codes
Number of digits per account code
Number of Account Codes- Unverified
Number of Account Codes - VerifiedUp to 12 unverified digits
Unlimited
250 Account Codes
ACD Groups
Groups
Members
RAN Announcements
Calls in QueueSoftwaresupportsupto16Groups
Software supports up to 252 stations in each Group
Eight RAN Announcements per system, 3 per ACD Group
All CO Lines may be queued for an ACD Group
Attendants Up to 3 stations can be designated as Attendants.
CO Lines
CO/PBX/Centrex Lines
DID Lines
T-1 Trunks
ISDN TrunksMPB1
48 maximumMPB2
144 maximum
Conference
Circuits
Par ties10 Conferences per system
8 parties per conference, of which 5 can be external
Dialing Memory
Station Speed Dialing
System Speed Dialing
Total Speed Dial20 Bins per station (24-digits)
980 Bins per system (24-digits)
3000 Bins per system (24-digits)
Digital DSS/BLF Units 180 maximum
Each DSS/BLF unit requires 1 station port and reduces station capacity by 1.
DSS/BLF maps may not be duplicated at one station.
1 station may have up to 3 DSS/BLF units associated with it.
DISA Circuits Unlimited number of CO lines may be programmed simultaneously.
Hunt Groups
Groups
Members
TypesSoftwaresupportsupto8Groups
Softwaresupportsupto8stationsineachGroup
Station, Pilot Hunting, or Pilot Ring All
Loop Supervision Disconnect 700 msec. duration (CO or Internal call to SLT )
Music Channels
Music-On-Hold/Background Music 8 Channels per system (4-8 on CO, ports 1 & 2 on MISB, port 3 on MPB2) (port 3 is
unavailable for MPB1)
Page Zones
Internal Paging
External PagingMPB1
8 maximum (software controlled)
2 maximumMPB2
8 maximum (software controlled)
3 maximum 
						

							System Configuration Tables2-7
Chapter 2 - System Specifications
Stations
Analog Stations
Digital Telephones
Single Line TelephonesMPB1
96 maximumMPB2
252 maximum
No more than 96 stations are
supported per Cabinet.
UCD Groups
Groups
Members
RAN Announcements
Calls In QueueSoftwaresupportsupto8Groups
Softwaresupportsupto8stationsineachGroup
Eight RAN Announcements per system, 2 per UCD Group
All CO Lines may be queued for a UCD Group
Voice Mail Groups
Groups
Members (ports)
Integration Method
Positive Disconnect
VM Message Wait
VM Disconnect SignalSoftwaresupportsupto8Groups
Software supports up to 24 stations per group
In-Band signaling (DTMF)
Loop supervision is provided to ensure disconnect
Programmable 12-digit (DTMF) string
If 0 digits are programmed, 15 sec of silence are followed by a busy tone.
Table 2-4: Environment Specification
Item Degrees (ºF) Degrees (ºC)
Operation Temperature 32-104 0-40
Optimum Operation Temperature 68-78 20-26
Storage Temperature 32-158 10-70
Relative Humidity 0-80% non-condensing
Table 2-5: Loop Limits
Item
Capacity
Analog Electronic Telephone* Maximum length of station loop:
1000 feet of 24 AWG
(4 wire, inside wiring, twisted cable)
Digital Telephones* Maximum length of station loop:
1000 feet of 24 AWG
(2-wire, inside wiring, twisted cable)
Single Line Telephones* 2000 feet of 24 AWG
*All stations must be installed in the same building. Station circuitry does not contain protection to support off-
premise operation.
Table 2-6: FCC Registration Numbers
System
FCC Number
For aKey Systemconfiguration (button appearance) KF: 5JYKOR-45505-MF-E
For aHybrid Systemconfiguration (dial access codes) MF: 5JYKOR-45505-MF-E
Table 2-3: System Capacity 
						

							2-8System Configuration Tables
Chapter 2 - System Specifications
Table 2-7: Electrical Specifications
Item
Specification
Power Supply
AC Voltage Input
AC Power
AC Input Fuse
DC Output Voltage120 or 220 +/- 10% Volt AC @48-63Hz
350W
5.0 amp @ 220Volt AC
+ 5V @ 10A, - 5V @ 1.5A, + 30V @ 8.4A
Battery Backup
Input Voltage
Battery Fuse
Charging Current24Volt DC
12.5amp @250Volt AC
Maximum 1A
External Relay Contact 1 amp @24Volt DC
Longitudinal Balance 60 db from 200 Hz to 1,000 Hz
40 db from 1000 Hz to 4000 Hz
Idle Channel Noise Less than 15 dbrnco for all connections
Cross Talk Attenuation Greater than 75 dbm Station to CO and Station to Station
Single Frequency Distortion
(300 - 3400 Hz)Station to CO Line and station to station:
Better than 2.0% or 34 db for an
Output level -30 dbm to 0 dbm
Ringing Detect Sensitivity 40Vrms @16-30Hz
30Vrms @30-37Hz
Ringer Equivalence Number (REN) LCOB: 0.8B; DIDB: 0.0B; T1IB: 6.0P
Co Line Signaling - DTMF Frequency pair at ±5dbm
Frequency tolerance ±1.5%
CO Line Signaling - Dial Pulse 10 pps and 20 pps programmable
Input Level Range +10 db maximum
Music Source
Music-On-Hold input
Background Music input600Ω input atØdbm maximum from music source
600Ω input atØdbm maximum from music source
External Page Port
Output Impedance
Output Power w/o Compression600Ω @ 0dbm
5 milliwatt max
CSA File Number (NRTL/C) LR57228
Telephone Transmitter Electret mic compatible 
						

							System Configuration Tables2-9
Chapter 2 - System Specifications
Table 2-8: Dialing Specifications
Item
Specification
DTMF Dialing
Frequency Deviation
Rise Time
Duration of DTMF Signal
Interdigit TimeLess than +/-1%
Maximum 3ms
Minimum 75ms
Minimum 75ms
Pulse Dialing
Pulse Dialing Rate
Pulse Break/Make Duration10 or 20 pps
60/40% or 67/33%
CO Type Loop Start, 600 ohm, current sensing
Table 2-9: Trunk Ordering Info: Public Network/Private Lease Lines
System Port Identification, Facility Interface and Service Order Codes
Interface Card Ringer Equivalent Number (REN) Facility Line Interface Jack Type
CO Port (LCOB) 0.8B 02LS2 RJ11
CO Port (LCOBE/LCOBC) 0.8B 02LS2 RJ21X
Direct Inward Dial (DIDB) 0.0B 02RV2-T RJ11
T-1 Port ( T1IB) or
ISDN Port (PRIB)6.0P 04DU9-B RJ45
Table 2-10: Dimension and Weight
ItemHeight Width Depth Weight
in mm in mm in mm lbs kg
KSU 16.2 411 24.8 630 9.4 238 25.3 11.5
Digital Keyset 9.3 236 7.6 192 3.3 84 3.3 1.5
Digital DSS/BLF Console 9.3 236 4.9 125 2.4 62 2.0 0.9 
						

							2-10System Configuration Tables
Chapter 2 - System Specifications
Table 2-11: Electronic Telephone Audible Signals
Type of Signal FrequencySignal Duration
(in seconds unless otherwise indicated)
Electronic Telephone Signals
Incoming CO Line 440+480 0.4 on/0.4 off/0.4 on/2.0 off; Repeated
Intercom Tone Ringing 440+480 0.8 on/2.4 off; Repeated
Intercom Call Announce (H-P modes) 440 0.2 on/0.2 off; (3 bursts)
Transferred CO Line 440+480 0.8 on/2.4 off; Repeated
CO Line Recall 440+480 0.24 on/0.6 off; Repeated
Message Wait Call Back 440+480 0.8 on/2.4 off; Repeated
CO Queue Call Back 440+480 0.8 on/2.4 off; Repeated
Camp-On 440 0.8on(1burst)
Paging Alert Tone 440 1.0 on
Type of Signal FrequencySignal Duration
(in seconds unless otherwise indicated)
Electronic Telephone Confidence Tones
Intercom Ringback 440+480 0.8 on/2.4 off
Transferred CO Line 440+480 0.8 on/2.4 off
Call Announce 440 0.2 on/0.2 off; (3 bursts)
Busy Tone 480+620 1.0 on/0.2 off/1.0 on/0.2 off/0.2 on/ 0.2 off/
0.2on/0.2 off/0.2 on; Repeated
Error Tone 480+620 0.2 on/0.1 off; Repeated
Intercom Dial Tone 350+440 Steady
DND Tone 350+440 0.4 on/0.4 off/0.2 on/0.2 off/0.2 on; Repeated
Paging Confirmation Tone 350+440 1.0 on
Conference Time-out/Re-Enter Tone 440 Programmable Steady Tone
Confirmation Tone 350+440 0.2 on/0.2 off; (3 bursts) CO/PBX