Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

ProgrammingD-11
Appendix D - Voice Over the Internet Protocol
Setting Up the CO Line Groups (FLASH 40)
The CO Line Group must be programmed for the Discovery VoIP CO lines. In addition, a TIE 
circuit must be established to provide system-to-system connectivity.
1. While in programming mode, dial [FLASH 40].
2. Dial the appropriate range that equals the CO time slots used (e.g., 001-008 or 006-013), 
then press HOLD.
3. Press Button 8, enter an available Line Group (01-23) based on your existing system...

D-12Programming
Appendix D - Voice Over the Internet Protocol
3. Press the appropriate button listed below to modify the table.
Conditions
»  Feature access codes must not conflict with station numbering.
»  CO line numbers are fixed and cannot be changed other than the current FLASH 42 
reassignment.
»  The VMID digits need to be programmed separately.
»  The SMDR will output up to 4-digit numbers in the station field. If less than 4 digits are 
selected in the numbering plan, leading spaces will be...

OperationD-13
Appendix D - Voice Over the Internet Protocol
Operation
The Discovery VoIP card operates like all other Central Office cards. There are up to 8 lines per 
card, and each line functions as any other CO line functions. It allows bi-directional 
communication and monitors for disconnect while using minimal bandwidth. It also allows 
four-digit dialing and other features.
When using Discovery VoIP lines:

If a button is programmed, a busy lamp field (BLF) will illuminate (on initiating station...

D-14 IP Telephony Standards and Protocols
Appendix D - Voice Over the Internet Protocol
IP Telephony Standards and Protocols
The Discovery VoIP card uses the H.323 Revision standard for call processing. This is an 
updated version of the H.323 standard. It provides a set of standards defining real-time 
multimedia communications and conferencing over packet-based networks. These 
standards define how components that are built in compliance with H.323 set up calls, 
exchange compressed audio and video,...

Vo I P  Gl o s s a r yD-15
Appendix D - Voice Over the Internet Protocol
Vo I P  G l o s s a r y
This table describes the Internet Telephony terms used in this section:
Term Definition
Asynchronous
TransmissionA method of data transmission which allows characters to be sent at irregular intervals by preceding each 
character with a start bit and following it with a stop bit
bps Data bits per second, also known as Baud Rate
DTMF Dual Tone Multi-Frequency
Gateway Bridges H.323 conferences to other network...

D-16VoIP Glossary
Appendix D - Voice Over the Internet Protocol 

E
Customer Database
Programming
This appendix provides information about database programming. Use the detailed
procedures contained in other chapters and appendices for actual programming via
executive display telephone. Use the Customer Database Worksheets in this appendix
to help keep track of the system programming changes made for each individual
system. 












 
 
 
 
 
 

IntroductionE-3
Appendix E - Customer Database Programming
Introduction
The XTS system is programmed to meet each customer’s individual needs. All programming 
is done at any 24-Button Executive Telephone as the programming station or through an 
ASCII terminal or PC. The digital display model is required for programming.
When the programming mode is entered, the digital telephone being used no longer 
operates as a telephone but as a programming station with all of the buttons redefined. The 
keys on...

E-4Introduction
Appendix E - Customer Database Programming
When using a PC to program the system, the following chart presents the data terminal 
characters that are equivalent to the key set buttons.
Figure E-1: Data Terminal Program Codes Cross Reference
Figure E-2: Programming Button Mapping
Some features must have more than one data field programmed for that feature 
to work. This information is stated in the instructions.


	





	




	





	


...