Sony Vpl Cx80 Projector User Manual

11

12
 ï´­”»”°a
*/165
 z

13	s

2About the Supplied Manuals
About the Supplied 
Manuals
The following manuals and softwares are 
supplied with this unit.
For the VPL-CX80, read the Safety 
Regulations, Quick Reference Manual, and 
Operating Instructions (for the VPL-CX86/
VPL-CX80). Other manuals on the CD-
ROM and other software applications were 
not prepared for the VPL-CX80.
Also, the Operating Instructions for the 
VPL-CX76/VPL-CX70 are included on the 
CD-ROM, but are not used for this unit.
On Macintosh system, you can read only...

3About the Quick Reference Manual / Using the CD-ROM Manuals
About the Quick 
Reference Manual
This Quick Reference Manual explains the 
connections and basic operations of this unit, 
and gives notes on operations and 
information required for maintenance.
For details on the operations, refer to the 
Operating Instructions contained in the 
supplied CD-ROM.
For safety precautions, refer to the separate 
“Safety Regulations.”
Using the CD-ROM 
Manuals
The supplied CD-ROM contains Operating 
Instructions...

4Notes on Use
Notes on Use
Use the supplied power cord when you use the projector in your country/region. Otherwise, use 
a proper power cord meeting the following specifications.
1) Use the correct plug for your country/region.
Do not block ventilation holes (exhaust/intake).  If they are blocked, internal heat may build up 
and cause fire or damage to the unit.
Check the positions of the ventilation holes shown in the following illustrations.
For other precautions, read the separate “Safety...

5Projecting
Projecting
When you connect the projector, make sure to: 
• Turn off all equipment before making any connections.
 Use the proper cables for each connection.
 Insert the cable plugs firmly.  When pulling out a cable, be sure to pull it out from the plug, not the cable itself.
Refer also to the instruction manual of the computer to be connected.
Connecting with a computer
Wired connection
1 Connect the AC power cord to a wall outlet and connect the computer and the projector.
2 Press the...

6Projecting
Wired connection - when using Air Shot (wireless connection) function (VPL-
CX86 only)
1Insert the supplied wireless LAN card.
2Connect the AC power cord to a wall outlet.
3Press the ?/1 (on/standby) key.
4Press the AIR SHOT button on the remote commander.
5Turn on the power the computer.
6Confirm that the switch on the wireless LAN module is set to the WIRELESS LAN side, 
and then insert the USB wireless LAN module into the computer.
When the Air Shot is used for the first time, install the...

7Projecting
1Adjust the position of the picture.
2Adjust the size of the picture.
3Adjust the focus.
The projector is equipped with the PICTURE SETTING menu to select the picture mode, 
and the INPUT SETTING menu to select the appropriate aspect ratio of the picture.  For 
details, see the Operating Instructions contained in the CD-ROM.
1Press the ?/1 (on/standby) key.
2When a message appears, press the ?/1 (on/standby) key again.
3Unplug the AC power cord from the wall outlet after the fan has stopped...

8Replacing the Lamp
Replacing the Lamp
The lamp used as a light source is a 
consumable product. Thus replace this lamp 
with a new one in the following cases.
 When the lamp has burnt out or dims
  “Please replace the Lamp.” appears on the 
screen
 The LAMP/COVER indicator lights up
The lamp life varies depending on 
conditions of use.  
Use an LMP-C190 Projector Lamp as the 
replacement lamp.
Use of any other lamps than the LMP-C190 
may cause damage to the projector.
The lamp remains not after the...